Search Documents

By J. F. T. Agapito

OCI Wyoming mines two flat-lying trona seams that are 3- to 3.5-m- (10- to 11.5-ft-) thick, about10 m (33 ft) apart and 250-m- (820-ft-) deep at its Big Island Mine in Wyoming. Continuous miners and a yielding-pillar system have contributed to improvements in resource recovery and productivity. The use of yield pillars minimizes the stresses transmitted from the upper to the lower seam. However, yielding must not impact the good, long-term stability needed to prevent subsidence for a large portion of the mine beneath the Green River channel.

Jan 1, 2000

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

By W. P. Lass

The purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Qold Mining Co., at Douglas Island, Alaska, under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows : Smelting-charges,......... $4.00 Loading, freight, insurance, etc., . 2.89 Interest due to time loat in transit and in settlement,... 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 6.01 Total,...$11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows : Per Day. Per Ton. Labor,. $86.16 $@.827 Chemicals,.76.60 0.960 Power and steam-heat,... 67.60 0.845 Marketing-, refining- and other charges, . 49.36 0.617 Totals,.. $2.59.72 $3.250 Adding to this total the 4 per cent. treatment-loss, which on 3-02. concentrates amounts to $2.48, gives a total cost of $5.13 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Jan 1, 1912

By Brooke T. Mossman

Asbestos fibers are highly fibrous silicate fibers that are distinguished by having a large aspect (length to diameter) ratio and are crystallized in an asbestiform habit that causes them to separate into very thin fibers or fibrils. These fibers are distinct from nonasbestiform cleavage fragments and may appear as thick, short fibers which break along cleavage planes without the high strength and flexibility of asbestiform fibers. Since cleavage fragments of respirable dimensions have generally proven nonpathogenic in animal studies, little data exists on assessing well-characterized preparations of cleavage fragments in in vitro models. The available studies show that cleavage fragments are less bioreactive and cytotoxic than asbestiform fibers. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestiform; Cleavage; Fibers; Fibrous

Jan 1, 2007

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

By J. Hartikainen

Kemi cardboard mill is founded on the alluvial bed of Kemi river at the north-eastern cost of Botnic Culf in Northern Finland. The alluvium consists of sandy and silty layers underlain by thick medium dense silty moraine layer. The first cardboard machine, having a belt width of 7,4 m, was constructed in 1972 on 7,5 to 9,5 m long wedge-shaped precast driven piles. Because of the excessive differential settlements and sometimes unexpected dynamic malfunctioning of the machine it was decided to strengthen the foundation before installing the partly new machine and increasing the running speed from 500 to 750 m/min. Piling was done under extremly strick limitations concerning space, vibrations, settlements, dust etc. Extra vertical support was made by using 23...25 long x-form steel piles driven by compressed air pile hammer down to rock. The piles were held together with old piles by a conctrete frame with diagonals, which made the total system - machine - foundation frame, piles and ground - ridgid enough to avoid resonance during dynamic loading.

Jan 1, 2010

By Richard Wilson

In the early 1970s, it became a concern that exposure to the mineral fibers associated taconite ore processed in Silver Bay, Minnesota would cause asbestos-related disease including gastrointestinal cancer. At that time data gaps existed which have now been significantly reduced by further research. To further our understanding of the types of airborne fibers in Silver Bay we undertook a geological survey of their source the Peter Mitchell Pit, and found that there are no primary asbestos minerals at a detectable level. However we identified two non-asbestos types of fibrous minerals in very limited geological locales. Air sampling useful for risk assessment was done to determine the type, concentrations and size distribution of the population of airborne fibers around Silver Bay. Approximately 80% of the airborne fibers have elemental compositions consistent with cummingtonite-grunerite and the remaining 20% have elemental compositions in the tremolite-actinolite series. The mean airborne concentration of both fiber types is less than 0.00014 fibers per milliliter that is within the background level reported by the World Health Organization. We calculate the risk of asbestos-related mesothelioma and lung cancer using a variety of different pessimistic assumptions. (i) that all the non-asbestos fibers are as potent as asbestos fibers used in the EPA-IRIS listing for asbestos; with a calculated risk of asbestos-related cancer for environmental exposure at Silver Bay of 1 excess cancer in 28,500 lifetimes (or 35 excess cancers per 1,000,000 lifetimes) and secondly that taconite associated fibers are as potent as chrysotile the least potent form of asbestos. The calculated risk is less than 0.77 excess cancer case in 1,000,000 lifetimes. Finally, we briefly review the epidemiology studies of grunerite asbestos (amosite) focusing on the exposure conditions associated with increased risk of human mesothelioma. © 2008 Elsevier Inc. All rights reserved. Keywords: Risk; Fibers; Particles; Taconite; Asbestos; Exposures

Jan 1, 2007

"One of the functions of the United States Bureau of Mines is to investigate the ability of electrical mining equipment to operate in a gassy mine without danger of igniting explosive atmospheres. To accomplish this purpose, tests are made in which mixtures of gas and air are ignited in the equipment while it is surrounded by explosive atmospheres of the same composition. In such tests, records of pressures developed by the internal ex-plosions are obtained and observations are made of any flames, sparks, or smoke which may issue from bearings and joints. Occasionally the explosion pressures in a mining machine rheostat or a compartment of some other machine reach a value which is judged to be excessive or abnormal.A number of factors are known to influence the explosion pressures, and both German and. British investigators have irate extensive research on their effects. Much of this work had been done with artificial compartment which certain conditions could c held, constant while others were being varied. The U. S. Bureau of Mines has not made any research on a scale to compare with that of the British or German investigators; however, special studies have been necessary from time to time to determine the cause and remedy for high pressures obtained in the routine test of some piece of mining machinery. Thus it has been possible to verify some of tee theories established on a purely experimental oasis by practical tests of machines as actually built for mine use.Some of the factors determined the pressure that will result when an explosive mixture in a compartment or connected compartment is ignited are: (1) The volume of explosive mixture ignited, (2) the percentage of as in the mixture, (3) the amount of coal-dust in the compartment or compartments, (4) the degree of movement or turbulence of the mixture at the time of ignition, (6) tightness of the joints and bearings, (6) the size of opening between, compartments, (7) the distance between the point of ignition and openings, and (8) the cooling, effect of surfaces and of material inclosed in the compartments."

Dec 1, 1929

By T. E. Bernard

"Refuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet the U.S. Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and management of heat from the occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements and carbon dioxide generation that are representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current U.S. coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in.) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in a refuge alternative. The highest likely metabolic heat generation ranged from 113 to 134 W, depending on occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 L (0.81 cu ft) of oxygen per hour per person and 20 L (0.71 cu ft) of carbon dioxide per hour per person, which means the margin of safety is 50 percent or more compared with the MSHA requirements. The information on metabolic heat generation can be used to assess refuge alternative thermal environments by testing or simulation. The required oxygen supply and carbon dioxide removal can be used to assess refuge alternative requirements. IntroductionRefuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet U.S. Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen (O2), removal of carbon dioxide (CO2) and management of heat resulting from the refuge alternatives’ occupants and mechanical/ chemical systems (MSHA, 2008)."

Jan 8, 2018

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960

By R W. Drybrough

The program to increase production at Sherritt Gordon's Lynn Lake property, which began in 1956, included increasing the rope speed and the horsepower of the ore hoist at the "A" shaft. Because of the limited power sup-ply from the two 7,000-hp. hydroelectric plants, and the ? 3,600 hp. predicted for the combined hoisting requirements of the three production shafts, it was considered desirable to lessen the impact of this type of load on the relatively small power system by equipping all future hoisting arrangements with Ward Leonard direct-current drives. The manually operated 8-by 4-ft. hoist at the "A" shaft had a rope speed of 1000 f.p.m., and was driven by a 385-hp., 380-r.p.m. wound rotor motor with liquid rheostat control. This A.C. drive was replaced by a semi-automatic Ward Leonard direct-current drive with a 515-hp., 566-r.p.m., shunt wound motor, providing a rope speed of 1,500 f.p.m. During several months preceding the con-version, all possible preparations were carried out to keep the changeover period to a minimum, and this resulted in a total shutdown time of twelve days. The capability of the "A" Shaft hoist was increased from 109 tons per hour to 134 tons per hour, and both mechanical and electrical maintenance were reduced considerably. The total cost of the conversion amounted to $130,000. The hoistmen who had been required for the manual A.C. drive were transferred to the new Farley shaft, and the reduction in operating labour costs of the "A" Shaft hoist

Jan 1, 1965

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By K. G. Wheeland, J. E. Dutrizac, M. Wasserlauf, A. A. Condy

Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of

Jan 1, 1988

An exploration and preliminary mine design contract was undertaken in Thailand to establish whether adequate lignite resources existed for the addition of future power generation plant through to the year 2000. The lignite ranges in heat value from 14 to 24 MJ/Kg (air dry basis) and occurs in 2 major seams consistituting measured reserves of 536 Mt (with an ash cut-off level of 45 % on an air dry basis) and a strip ratio of 4.1 bank cm/t. The paper describes the pre-planning, programming, equipment used, project management, logistics and exploration methods adopted to undertake the contract in a monsoonal area using Australian drilling and geophysical contractors.

Jan 1, 1983

By Alejandro Lagos

El modelamiento estructural de una zona es esencial para la búsqueda de zonas favorables para la mineralización. En ese sentido, el presente texto describe la geología estructural de las áreas de Cajamarca, San Marcos y Bolivar y su posible relación con la génesis de los yacimientos de minerales ubicados en ese sector y así diseñar un modelo estructural de las aéreas mencionadas apoyado por el método de mapas paleogeológicos.

Sep 14, 2009

By Holly J

The period following World War II has seen many changes in stoping techniques at The Great Boulder Gold Mine. The new methods resulted in improved unit production figures, and have given some relief from the rising worldwide cost spiral in the post war years.Significant production figures are shown graphically in...

Jan 1, 1956

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By A Asadov, D Nair

This paper discusses the determination of the percentage of crystalline material in a natural silica deposit which would be considered harmful to health (<10 ¦m). A sample of the natural silica material was recovered and split into a number of subsamples. Samples were sieved using a conventional dry sieve to remove material >300 ¦m before testing. Particle size analyses of the fine fraction showed 75 per cent of the material was below 10 ¦m. Initially XRD and XPS were run on the samples to determine the minerals and composition of the sample. The XRD revealed strong quartz peaks and smaller tridymite peaks with a high amorphous background. The XPS indicated traces of iron, titanium and carbon with dominant silicon and oxygen peaks. The structure of the sample was investigated using the SEM. It was apparent that there were a number of larger quartz crystals (>30 ¦m) with a mix of amorphous and crystalline in the finer fraction. It was also observed that amorphous material was attached to the surface of the crystals. In order to determine the percentage of crystalline quartz a known amount of quartz was added to the sample incrementally. On each addition an XRD scan was performed and the area under the peaks recorded. Back analysis of these peaks with an assumed percentage of crystalline material in the original sample gave a crystalline content of 30 per cent. The quantity at the respirable fraction was estimated to be 18.7 per cent.

Jan 1, 2003