Search Documents

By M Slight, H Lacy

In recent times, with the global mining industry’s focus on sustainable development there has been a significant focus on mine closure and rehabilitation performance and reporting through the development of the International Council on Mining Metals (ICMM), the Global Reporting Initiative and the Equator Principles. In addition, financial reporting obligations under International Financial Reporting Standards and the Sarbanes Oxley Act (2002) have also led to better understanding and improvements with industry closure performance, liability management and reporting.Under these sustainable development principles and financial reporting obligations, mining companies are required to consider mine closure planning and associated cost estimates across all life cycle phases of the mine. Internal processes have been developed within mining companies to better understand their closure liabilities and obligations and likely costs and cost estimating processes are generally developed for long-term life-of-mine (asset) planning and budgeting, financial reporting for corporate balance sheet provisioning purposes, and regulator reporting for environmental bonding and financial assurances.These days mining companies need to plan for, prepare and actually mine for closure right from the start of a project. This means that their closure and rehabilitation liabilities throughout each stage of the mine life cycle phases must be understood, planned for, managed and controlled.So how is the industry performing? Understanding of closure liabilities is improving and reflected in liability cost estimations that are recognising the likely issues to be faced at closure, but there is a way to go to ensure that the industry doesn’t add to the increasing legacy liabilities being passed onto the wider community.CITATION:Slight, M and Lacy, H, 2016. Closure liabilities – where are we at?, in Proceedings Life-of-Mine 2016 Conference , pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By C. Lupi

"The energy consumption of copper production by electrowinning, generally represents more than 1/4 of the total energy requirement in hydrometallurgical traditional process (roasting, leaching, purification and electrowinning). The considerable saving can be achieved just in this step that requires about 2.2 kWhlkg of the produced copper. To save energy the cell voltage, or more appropriately its anodic component, can be reduced: that is because the anodic voltage represents the main component of cell voltage and so it is largely responsible for the excessive energy consumption in copper sulphate electrowinning.In this work some ways are studied to lower the anodic voltage. First the cobalt ions were added to the sulphate solution in order to study the catalytic effect on oxygen discharge. Then lead alloys anodes (Pb-Ag, Pb-Sb-Ag and Pb-Ca) were used to promote a better oxygen evolution as a result of a different anodic surface. Their behaviour was compared with the PbSb traditional ones. Finally, as already pointed out by several authors for zinc electrowinning, ethylene glycol was employed as anodic depolariser in order to verify its effectiveness in the case of copper electrowinning. By combining all the above-mentioned ways, energy saving ranging from 20% to 27% is achieved.All the tests were carried out on a laboratory pilot-plant for long time to simulate the industrial conditions. The obtained copper deposits were observed by SEM to highlight their morphology."

Jan 1, 1997

By John L. Lamont, Walter Crafts

THE principle formulated by Grossmann1 for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the in¬creasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. TESTING PROCEDURE Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 20 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixtures of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of an MgO-stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2007

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz, Thiago Soares Lima, Rafael Kakitani

Materiais de interface térmica (Thermal Interface Materials - TIMs) são responsáveis pela troca térmica entre a fonte geradora de calor do processador integrado e o dissipador de calor. Devido ao seu baixo ponto de fusão, boa fluidez e cumprimento com as exigências de regulamentação (Restriction of Hazardous Substances - RoHS), ligas à base de bismuto têm sido investigadas para aplicação como TIMs de alta performance. Neste contexto, a análise das propriedades dessas ligas em função de parâmetros microestruturais torna-se, portanto, de elevado interesse científico e tecnológico para o setor eletrônico. Assim, este trabalho tem como objetivo desenvolver correlações entre propriedades de resistência à tração e a microestrutura da liga Bi-0,28%Ni solidificada sob um intervalo de taxas de resfriamento usualmente obtido em processos industriais. Por meio de microscopias óptica e eletrônica de varredura foi observada uma morfologia tipicamente eutética lamelar, composta por lamelas ricas em bismuto com o intermetálico Bi3Ni nos contornos. Os espaçamentos lamelares (λL) foram, então, correlacionados com os parâmetros térmicos de solidificação, sendo propostas leis experimentais de crescimento microestrutural. Ao fim, observou-se que, para λL < 101 μm, equações do tipo Hall-Petch caracterizam a variação do limite de resistência à tração e do limite de escoamento.

Oct 1, 2019

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By G McKay, M Erskine, S Macklin

The City of Sydney is currently investing in a number of infrastructure projects that require tunnel excavations within the Triassic Hawkesbury Sandstone. It is generally accepted that this formation has high residual stresses of ‘tectonic’ origin, so much so that these stresses have been implicated in a number of well-known failures and problems for tunnelling. These include failure of ‘roof beams’ comprising discrete beds in the crown of tunnel excavations; stress-induced spalling and ‘slabbing’ of tunnel walls; shear displacement between beds causing the failure of rock bolts; strain in adjacent infrastructure and, the necessity for re-grouting of high conductivity fractures due to stress relief dilation after excavation. Whilst there is an extensive published database of in situ stress measurements comprising ‘hydrofrac’, ‘over-coring’ and ‘slotter’ stress measurements, these data indicate a considerable spread of results. The traditional approach to interpreting this data has been to attempt to fit linear correlations to stress versus depth data, based on personal experience and ‘back-analysis’ of monitoring data during construction. However, there are a number of such correlations in the literature and there is divergence of opinion regarding the assessment of ‘background’ in situ stress and appropriate upper and lower bound values for design. This paper provides a brief review of the published data; suggestions on an alternative ‘risk-based approach’ to assigning in situ stresses for design; and, proposals on how in situ stress tests may be conducted in future to improve the quality of the database available to designers.CITATION:Macklin, S, McKay, G and Erskine, M, 2014. A review of the in situ stress database for tunnel design in the Hawkesbury Sandstone, Sydney, New South Wales, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R. Woods

"Comments on the paper ""Formation of hydrogen peroxide by chalcopyrite and its influence on flotation,""by A. Javadi Nooshabadi and K. Hanumantha Rao (Minerals & Metallurgical Processing, 2013, Vol. 30,No. 4, pp. 212-219)The formation of hydrogen peroxide from water during the grinding of chalcopyrite in a nitrogen-sparged environment, as reported by Javadi Nooshabadi and Rao (Minerals & Metallurgical Processing, 2013, Vol. 30, No. 4, pp. 212-219), is questioned on the grounds that oxidation of water by the mineral is unlikely to be thermodynamically feasible. It is argued that it is more likely that any peroxide that had been formed would have been generated from residual oxygen in the nitrogen-flushed system than from the oxidation of water.The formation of hydrogen peroxide by finely divided pyrite had been reported by a number of authors (Borda et al., 2001; Borda et al., 2003; Cohn et al., 2006; Schoonen et al., 2006; Schoonen et al., 2010; Jones et al., 2011; Javadi Nooshabadi et al., 2013). That hydrogen peroxide is formed in the presence of oxygen in solution can be comprehended from wellestablished mechanisms. Pyrite in aerated solution is known to oxidize by an anodic process that is coupled with the cathodic reduction of oxygen (Holmes and Crundwell, 2000). The latter process has been shown to occur through the formation of hydrogen peroxide (Biegler et al., 1975; Ahlberg and Broo, 1996). The pH dependence of cathodic oxygen reduction at other sulfide minerals, including chalcopyrite (Biegler et al., 1977; Rand, 1977), implies a similar mechanism at these surfaces."

Jan 1, 2015

By H. Y. Sohn, Joshua E. Ramos, Moo Eob Choi

"A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. This technology would drastically lower CO2 emission and reduce energy consumption by nearly 38% of the blast furnace requirements. Experiments were performed using iron oxide concentrate at 1150oC in a bench-scale facility, which was the highest temperature that could be reached in the facility. The reduction extent was determined at residence times of 3.5 - 5.5 seconds in which the reduction extent approached 43% with 0% excess H2 and 95% with 860% excess H2. Separate kinetics measurements showed that the rate is much faster at 1200 - 1400 oC. Experiments were also carried out using syngas (mixtures of H2 + CO). About 90% reduction in 3.5 seconds with 860% excess hydrogen contained in the syngas demonstrated sufficiently fast reduction for a suspension process and the feasibility of usingsyngas instead of pure hydrogen.IntroductionDespite the improvements in the modern blast furnace (BF) process, it suffers from many drawbacks. The process requires the feed in the form of sinters or pellets and high-grade coking coal. Thus, BF iron production is projected to decrease gradually [1]. The main factors for this are the environmental regulations [2] and the high capital investment cost.A large number of new ironmaking technologies have been developed or are under development [3]. Most of these processes, however, are not sufficiently intensive to replace the blast furnace because they cannot be operated at high temperatures due to the sticking and fusion of particles. Therefore, a new technology is under development for producing iron directly from fine concentrates by a gas-solid suspension technology, which would reduce energy consumption by about 38% of the amount required by the blast furnace and drastically lower environmental pollution, especially CO2 emission, from the steel industry."

Jan 1, 2009

This paper evaluates the effect of longwall mining on a cluster of unconventional shale gas wells located in a district barrier pillar between a current longwall panel and the future panel north of the barrier pillar. A cluster of 19 unconventional shale gas wells have been drilled and 5 additional gas wells have been proposed in the barrier pillar. The closest gas well is 25.6 m (84 ft) to the current panel tailgate and 26.2 m (86 ft) to the tailgate of the future panel north of the barrier pillar. The rib-to-rib width of the barrier pillar is 57.9 m (190 ft). The distance between the two gas wells across the barrier pillar is 6.1 m (20 ft). The pillars in the current tailgate are on 22.9-m (75-ft) and 32.0-m (105-ft) centers, and the pillars in the tailgate of the panel north of the barrier will be on 22.9-m (75- ft) and 36.6-m (120-ft) centers. The two longwall panels adjacent to the barrier pillar are 475.5-m (1,560-ft) wide. The overburden depth at the shale gas well site is 321.6 m (1,055 ft). The wells have been installed in the barrier pillar, and the current district panel and subsequently the panel north of the barrier will be developed and retreated in the near future. The average min

Jan 7, 2020

By C. Sun

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By Alfred H. Hesse, Edwin T. Myskowski

The development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly IOO per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson&apos;s X-ray data indicate that this decomposi-tion is accompanied by a change in volume of as much as ; per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter6 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to go per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparalion of Alloys.—The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 CU-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to 1/2-in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.—The tensile specimens, 0.313-in. diameter (1.25-in. gauge length),

Jan 1, 1942

By Edwin T. Myskowski, Alfred H. Hesse

The development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly IOO per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson&apos;s X-ray data indicate that this decomposi-tion is accompanied by a change in volume of as much as ; per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter6 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to go per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparalion of Alloys.—The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 CU-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to 1/2-in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.—The tensile specimens, 0.313-in. diameter (1.25-in. gauge length),

Jan 1, 1942

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau&apos;s experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By John Lamont, Walter Crafts

The principle formulated by Grossmannl for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the increasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been! determined. The results of the study offer strong confirmation of the general validity of Grossmann&apos;s multiplying principle. Testing Procedure Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 29 in Grossmann&apos;s paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann&apos;s paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By John Lamont, Walter Crafts

The principle formulated by Grossmannl for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the increasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been! determined. The results of the study offer strong confirmation of the general validity of Grossmann&apos;s multiplying principle. Testing Procedure Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 29 in Grossmann&apos;s paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann&apos;s paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The US Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance for mining equipment. This will help increase mining productivity and decrease operating costs by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1992

By Daniel H. White

Block caving, unlike most other conventional forms of mining relies principally on the natural forces within the rock mass to fragment and transport the ore. Obviously, not every orebody can be satisfactorily mined by block caving. In the early stages of mine planning an attempt should be made to assess the benefits of the block caving system relative to others, and develop a reasonable mining concept that may be used to provide preliminary information to mine planners and financial specialists. It is the intention of this paper to outline some basic geotechnical parameters that are essential to: 1) Assessing the feasibility of block caving an orebody and 2) Providing semidetailed information relative to mine design based on drill hole and other data.

Jan 1, 1979

By N. M. Langdon

ON account of its greater economy and cleanliness, and the extent to which iuferior fuels can be utilized for its generation, there has been of late a rapidly increasing tendency to substitute gaseous for solid fuel for metallurgical and other industrial purposes, which has led to various improvements both in the process and apparatus for its manufacture, notably among which may IN mentioned the Tessie Gas Producer* described by Mr. A. L. Holley. A considerable experience by the author with producers of various kinds using anthracite fuel, in connection with the Taylor ore-roast ing furnace at Chester, N. J., with more or less unsatisfactory resnlts, finally led to the erection of the experimental producer described below, which combines in its construction, simplicity, dorability, and accessibility for cleaning and removing the ash and manipulating the fuel. It is adapted to the use of various kinds of fuel, and is capa ble of generating a steady and uniform supply of gas at a minimum cost. It has been in constant use day and night for about five months, and has given very satisfactory results. The producer, as shown in the accompanying sketch, consists of a cylindrieal furnace, preferably inclosed in an iron jacket or casing, having a bosh or inverted cone-shaped base as in a blast furnace. It is provided with a bell and hopper, the bell being hung to a forked lever, and having guide flanges to prevent it from swing ing, and an opening at its apex through which to insert a bar for manipulating the fuel, which when not in use is closed with a plug or stopper. Cleaning is effected through two small doors placed opposite each other at the hearth level, which in order to facilitate the operation is elevated above the floor. The doors are removable, and when closed are by their own weight and by means of bevelled lugs held tightly against their frames, forming a practically tight joint. A blast of commingled steam and air is injected into the fuel through a series of tuyeres underneath the bosh communicating with steam jet injectors. A small flue also connects the door

Jan 1, 1884

By D. Nebbia, R. Aliberti, F. Solesin

The launch of a Tunnel Boring Machine (TBM) is one of the most challenging activity parts of the construction of a tunnel. Challenges are coming from limited space available, learning curve, concurrence of other activities and in some cases from the geological conditions. Launching a TBM is an extraordinary and complicated operation requiring a great level of planning. The Earth Pressure Balance (EPB) TBM named “Chris” was successfully launched for the Northeast Boundary Tunnel, the largest component of the Clean Rivers Project in Washington, DC. Due to space and time constraints, the 8-meter diameter TBM was launched from a single 20-meter diameter shaft, with a 30-meter-long tail tunnel by means of umbilical connections. This paper presents the steps followed during the TBM assembly and launching to complete the excavation of the initial drive of the tunnel maintaining high level of efficiency and quality despite the space constraints. Specifically, it focuses on the methods and phases used to extract the excavated material (muck) from the TBM and from the tunnel, to supply consumables, precast rings and backfill grout. The paper presents results in terms of productivity, lesson learned and possible alternatives to be considered in similar conditions.

Jun 13, 2021