Search Documents

By D. J. Parker, J. B. Benson, J. H. Bird, F. E. Cash

"INTRODUCTION The organic act that became effective July 1, 1910, imposes two very definite primary obligations upon the Bureau of Mines: (1) The prevention of loss of life and limb and the protection of the health of workers in the mineral industries, and (2) the conservation and scientific utilization of the country's mineral resources.The subject of this publication falls within the scope of both of these responsibilities by reason of the fact that (1) certain safety precautions are involved in combating even surface fires and, (2) although peat is not now, so far as known, utilized commercially or otherwise in this country as a fuel, it is extremely valuable agriculturally in at least one of our States, The justification for the conservation of such low-grade fuel through fire prevention appears warranted because of its present value to agriculture and the possible advantages accruing to future generations as a source of heat and power.Although the Bureau of Mines has published information on the origin and uses of peat, this is the first attempt to give out data concerning the prevention and control of peat-bog fires. Although the information presented here is restricted to the Lake Superior District, California, and Florida, there may be similar conditions in other sections of the country that have not come to the attention of engineers of the Bureau of Nines."

Jul 1, 1947

By Joo Hyun Park, Soo Sang Park

The distribution behavior of Pb between molten copper and FetO-SiO2 (-CaO, Al2O3) slags was investigated at 1473 K (1200 oC) and p(O2)=10-10 atm in view of the reaction mechanism of Pb dissolution into the slag. The distribution ratio of Pb (LPb) decreases with increasing CaO content (~6 mass pct) irrespective of Fe/SiO2 ratio (1.4~1.7). However, the addition of alumina into a slag with Fe/SiO2=1.5 linearly decreases the LPb, whereas a minimum value is observed at about 4 mass pct Al2O3 at Fe/SiO2=1.3. The log LPb continuously decreases with increasing Fe/SiO2 ratio, and the addition of Al2O3 (5 to 15 mass pct) into the silica-saturated iron silicate slag (Fe/SiO2 < 1.0) yields the highest Pb distribution ratio. The log LPb linearly decreases by increasing the log (Fe3+/Fe2+) value. The Pb distribution ratio increases and the excess free energy of PbO decreases with increasing Cu2O content in the slag. However, from the viewpoint of copper loss into the slag, the silica-saturated system containing small amounts of alumina is strongly recommended to stabilize PbO in the slag phase at a low Cu2O content.

Jan 1, 2014

By Jerome P. Downey

Technologies developed within the field of extractive metallurgy to recover, concentrate, and purify metals and industrial minerals from ores, have served as the foundation for all of the subsequent environmental remediation, materials recycling, and waste management technologies. This paper discusses the application of classical extractive engineering principles to the development of a thermal process for the recovery of mercury from solid wastes. Process development is presented as a series of logical stages, which begin with a thorough characterization of the site-specific waste, move on to bench and pilot scale testing of the process options, and end with a functional process flowsheet. This paper also presents thermodynamic data on many mercury species of interest to the minerals, power, and chemical industries. These data can be used to model the speciation and recovery of the mercury as a function of various process parameters.

Jan 1, 2003

Many of the difficulties faced by the U.S. mineral industry in 1982 and 1983 emanated from the worldwide recession, from the high value of the U.S. exchange rate, and, in part, from actions taken by foreign governments to protect selected industries. While some problems will be minimized with continued worldwide economic recovery, others remain and may require special attention by U.S. policymakers. These problems include declining U.S. production capacity in selected mining and mineral processing industries, the impact of the high value of the U.S. exchange rate, and protectionist trade practices by competitor nations. Illustrative of the last is the International Trade Commission (ITC) determination in June 1984 that both the domestic steel and copper industries have been substantially injured by foreign imports. In its July 1984 recommendations to the President, the ITC suggested higher tariffs and quotas for 5 years on 70 percent of steel imports but conditioned the aid on cost-cutting and modernization steps by the domestic industry. In the copper decision, two commissioners recommended increased duties, two recommended that quotas be imposed, and one recommended that no relief be provided. The President decided in September to seek voluntary restraint agreements with nations that export steel to the United States and rejected both quotas and higher tariffs on copper imports. General Economic Setting This decade opened with the U.S. mineral industries struggling to deal with double-digit inflation, record high peacetime interest rates, and almost 7 years of oil-cartel-induced energy price increases that seriously affected the profitability of energy-intensive industries such as mineral production and processing.

Jan 1, 1985

By David Seymour

Newmont Gold Company (NGC) located in Northeastern Nevada has been processing carbonaceous and sulfide refractory gold ores through a chlorination circuit prior to cyanidation. A "Flash Chlorination" pilot plant was installed in 1987 in an effort to obtain higher chlorine utilization efficiency and increase gold extraction. The Flash Chlorination process oxidizes organic carbon and sulfide sulfur. It also deactivates preg-robbing carbon, making the ore amenable to cyanidation. Significant recovery improvements were observed using this new process. This scheme has also been instrumental in the processing of higher than normal grade ores at economic chlorine levels. The Flash Chlorination pilot plant has been successfully treating carbonaceous ore on a production scale since April 1988. This paper summarizes laboratory and pilot plant optimization test work, using conventional and statistical methods.

Jan 1, 1989

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By C. H. Kats, E. G. Meiter, J. J. Bloomfield

"INTRODUCTION.Street manholes for underground power and signal circuits, and for sewers vary in size from small openings that a workman can enter, to large central vaults. As the gas hazards in manholes are similar to those in mines, the mine safety committee of the Bureau of Mines was asked whether the miners' flame safety lamp is a practicable device for indicating inflammable gases in manholes.The coal miner detects firedamp (methane or CH4) with his flame safety lamp by observing the luminous can or the increased length of flame that appears when 1.5 per cent or more of the combustible gas is present. The lamp flame also warns him of lack of oxygen by going out when the oxygen becomes less than 16 to L7 per cent. A tentative rule regarding the proposed use of safety lamps at manholes has been suggested previously as follows: ""Testing for gas: Do not enter manholes until you have .assured yourself that the manholes are free from dangerous gases, by testing with an approved safety lamp, by ventilation, or by other adequate methods."" The Bureau's committee recommended that miners' flame safety lamps are not suitable,testing in manholes because hydrogen gas may be formed therein. The flame safety lamps approved by the Bureau of Mines for use in aseous mines are safe in presence of methane and while not tested against the members of the paraffin hydrocarbon series (CnH2n+2) higher than methane they been have been used therein; the lamps should not be used in hydrogen or acetylene they can initiate explosions in presence of these gases."

Oct 1, 1925

By D. Swanson

Cold Detonation Physics (CDP) is a patented new field of explosives and the name for the explosive that is produced when non-toxic dry ice (frozen carbon dioxide) is combined with powdered metals such as magnesium and aluminum, which are non-toxic and nitrogen-free. The explosive is detonator-sensitive and detonates according to the rapid reduction of carbon dioxide back to carbon, which produces solids comprised mainly of metal oxides and about 5% carbon. CDP was determined to produce a maximum of 300 liters of carbon dioxide per kilogram (4.81 ft3 /lb) and about 1.5 liters of carbon monoxide per kilogram (0.024 ft3 /lb). Both these figures shift according to metal content where higher metal produces less gases. According to theoretical modelling, the relationship between static pressure and metal content was determined to be an inverse parabolic curve with optimum pressure at 25% to 31% metal, depending on the type/s of metal/s used. Velocity of Detonation (VOD) was determined by measuring light at the wavefront with fiber-optic cable inserted into a series of holes drilled into the side of a 3-inch diameter (76 mm) schedule 40 steel pipe containing the mixture. The highest VOD was observed at 25% magnesium and measured between 2,500 to 4,500 m/s (8202 to 14,764 ft/s) when initiated by a 454-gram (1-pound) booster and an electric detonator. A 25% 50:50 alloy of magnesium and aluminum sample shot at a higher velocity than magnesium, according to how the alloy generated smaller pieces of shrapnel when compared with shrapnel from a magnesium test. CDP, using 25% alloy, was tested for blasting limestone by drilling 3.5-inch holes (89 mm) and inserting a 3-inch x 4-foot cardboard tube (76 mm x 1.22 m) with the mixture, packed to a density of 0.62 g/cm3 . The blast was initiated with an electric detonator, behaved like ANFO with more energy and fractured rock sufficiently across the entire length of the borehole. Seismic analysis determined that CDP produces lower ground vibrations than traditional explosives.

Jan 1, 2024

By Peng Lv, Shiqian Liu, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

The treatment process of a low-grade refractory gold ore containing sulfide minerals and carbonaceous matters was studied in this work. The gold extraction of this ore by all-sliming cyanidation was only 11.75%. Hence, a pretreatment was necessary. In this paper, a flotation-preoxidation-cyanide leaching process was developed. The concentrate from the flotation procedure was processed using different preoxidation methods. A concentrate containing 34.08g/t of gold with the gold recovery ratio of 81.20% was obtained by flotation. After roasting, microwave heating or alkaline pressure oxidation, the gold cyanidation ratio reached 82.37%, 81.26% and 71.09% respectively. Roasting was an effective, reliable and mature technique to oxidize sulfide minerals and carbonaceous matters. Roasting and microwave heating both produced dangerous environmental pollutants while alkaline pressure oxidation was eco-friendly.

Jan 1, 2015

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By J. O. Lewis, Carl H. Beal

The material for this paper was collected for the most part by C. H. Beal during the years 1916, 1917, and 1918. Many of the conclusions reached in regard to the life of oil wells have already been published by the Bureau of Mines 1 but those presented in this paper deal particularly with the theoretical aspects of oil production. The report discusses some of the fundamental factors governing oil production, taking up first the conditions affecting the. amount of oil in the oil sand, then those factors that control the rate of production of oil wells, and then discusses several related problems, most of which deal particularly with the effect of the production of one well on that of another.

Jan 1, 1921

By N. S. Raymon

As part of an interegency agreement with the Energy Research end Development Administration to develop unproved refractory materials for use in coal gasification processes, the Bureau of Mines reviewed the literature to determine the effect of steam, H2, CO, and CH4 as well as the alkali metal oxides K2O and Na2O on refractory materials. Emphasis was given to the performance of high-alumina castable and fired refractories to conditions expected in coal gasification processes. Approximately 85 references were reviewed with 40 cited in the text. The literature was found to contain little data directly applicable to the selection of refractory lining materials suitable for use under the conditions of temperature, pressure, and gas compositions expected in second generation coal gasification reactors.

Jan 1, 1976

By AIME AIME

QUALITY and size do not ordinarily go hand in hand, but there is good evidence that both these attributes reached a new peak at the Annual Meeting of the Institute in New York just concluded. Certainly, the total attendance of 2500 was far above any yet attained, as might be expected with the recent rapid growth of Institute member- ship. General comment indicates that the quality of the papers also was notable, though not measurable by so definite a yardstick as attendance. During the meeting 49 technical sessions were held, at which more than 250 formal papers were presented. In addition, there were some thirty special meetings of committees, Divisions, and other Institute groups. In reporting the Annual Meeting eleven years ago the statement was made that "unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger," and "the fifth floor, where a buffet lunch is served each day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size." Unfortunately the angel to succeed Andrew Carnegie, who financed the building of the present home of the Institute 35 years ago, has not yet &apos; appeared. Even if some one would merely build another elevator or two in the present building it would help. Fortunately, the modern auditorium of the American Radiator & Standard

Jan 1, 1940

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

By A. J. Forney

This report summarizes the findings of methods of treating caking coals in a fluid bed to destroy their caking properties. In batch tests it was found that several coals, including those with a free-swelling index greater than 8, could be decaed at temperatures from 400° to 425° C with a fluidizing gas composed of inert gas or steam containing 0.2 percent oxygen and a minimum residence LS,-;,&apos; of 5 minutes. When treatment decreased the free-swelling index from about 8 to 1-1/2 or lower, the resulting treated coal was noncaking. In a continuous unit with continuous feed and discharge of coal, slightly more severe conditions were required to decake the coal. For 18- to 100-mesh coal a temperature of 430° to 440° C and an oxygen-to coal ratio of 0.4 cubic foot of oxygen per pound of coal feed was necessary. Finer mesh sizes required lower oxygen-to-coal ratios. In tests using air only as the fluidizing medium and treatment temperatures well below the softening range, the caking properties of 150- to 200-mesh coal were destroyed in 30 to 40 minutes of residence time at 200° C. Coarser sizes of 18 to 48, 48 to 100, and 100 to 150 mesh required longer residence time.

Jan 1, 1966

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

The Particulate Mineralogy Unit has been established at the College Park, Maryland, Metallurgy Research Center. The Particulate Mineralogy Unit will have the responsibility within the Bureau of Mines for the characterization of particulate minerals which have potential for adverse environmental effects. The Unit will provide a focal point for identifying particulates in connection with environmental problems related to the activities of agencies such as OSHA, HEW, EPA, and MESA. The Particulate Mineralogy Unit is seeking to clarify the ambiguities surrounding the mineralogy of and terminology used for asbestiform minerals and other mineral particles. The Unit?s investigations of the morphology, composition, and structure of asbestiform minerals and their nonasbestos analogs have made its members recognized experts in this field. The information which it develops on the characterization of asbestos and other particulate mineral forms such as silica should provide a technically rational basis for decisions by regulatory agencies. Those desiring further information, contact Dr. W. J. Campbell, Program Coordinator, College Park Metallurgy Research Center, College Park, MD 20740, telephone: 301-344-4014. ALUMINUM: For over a month, domestic producers have priced 99.5 percent grade primary aluminum ingot at 48¢ per pound. In the same period, merchants raised ingot quotes by 1.5¢-2.5¢ to a range approaching 44¢-47¢ per pound.

Jan 1, 1976

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By C. F. Smart

THE heat treatment of the bronze composed of 88 per cent. copper, 10 per cent. tin, and 2 per cent. zinc, has been investigated by H. S. and J. G. S. Primrose,1 and also by the U. S. Bureau of Standards.2 The results obtained by H. S. and J. G. S. Primrose on dry-sand castings subjected to reheating followed by air cooling, or by quenching in water, are shown in Figs. 1 and 2. The values for tensile strength have been FIG. 1.-EFFECT OF QUENCHING ON DRY SAND CASTINGS (H. S. AND J. G. S. PRIMROSE.) converted from tons per square inch to pounds per square inch. Figs. 3and 4, have been plotted from values obtained by the Bureau of Standards on material of the same composition and treatment. Both investigations show that the ductility of the cast bronze is improved by heating to 700° C. and cooling in air, the strength not being impaired by this treatment. They are not in agreement, however, as to the effect of quenching, Messrs. Primrose reporting a decrease, and the Bureau of Standards an increase, in both strength and ductility when the cast bronze is heated to 600° or 700° C. and quenched.

Jan 9, 1919

By C. D. Woodward

THE subject of electric signals for the despatching off mining cages through shafts has received cousiderable attention recently from various mining companies. The Anaconda Copper Mining Co. has found it necessary to develop a system that is reliable, safe and simple in operation, and easy to repair. The movement of all mine cages or skips is under the direction of a station tender, who rides on the cages when men or supplies are being lowered or raised. When ore is hoisted, he is stationed at a skip pocket for loading and despatching the skips. For the station tender&apos;s use, two signal systems are installed in each hoisting compartment, and he is the only employee authorized to use them. One system is known as the "AC" or Station bells, as it is operated from the 110-volt, 60-cycle, power service; the other system, called the "DC" or shafts bells, takes its energy from closed-circuit primary batteries. As a supplement to the two main signals, a buzzer system is installed. The general arrangement is similar to "the main signal, except that there is a mine buzzer at each station. When a signal switch connected into the buzzer system is pulled down, all buzzers are operated, thus notifying the station tender that he is wanted at some particular level. Placed on the station posts, and within easy reach of the men on the cages, are the signal pull switches for the main signals. The station, or "AC," pull switches are furnished with a short rope as shown in Fig. 1, while the shaft, or "DC," pull switches are equipped with ropes that extend down the shaft past the next station. To avoid all confusion in the use of the three signal systems, a standard arrangement has been adopted in all mines for the location of the pull switches. Fig. 2 illustrates the position of the pull switch at the various mine stations for the main signal systems, but it does not show the buzzer pull switch; this is fixed to the roof timbers about 25 ft. back from the shaft. If the skip pockets are a considerable distance below the station, a pull switch for each main shaft compartment is connected to the "AC" system and placed at this point. However, if the distance is short, a light cord is attached to the station pull switches and dropped down to the skip pocket.

Jan 2, 1922