Search Documents

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

Undoubtedly other members have given their lives in the Service of the United States and the Allies during the past four years, but the following biographical notices are all that have reached us as yet. Lewis Newton Bailey Lewis Newton Bailey died of pneumonia at Camp Merritt, N. J., Apr. 30, 1918, at the age of 34 years. He was Master Engineer, Senior Grade, in the Fourth Regiment, U. S. Engineers, and although he was offered a commission as First Lieutenant shortly after enlisting, he preferred not to accept it until he had reached France. By those who knew him well, this lack of eagerness for promotion will be recognized as consistent with his whole character. Mr. Bailey was born at San Diego, Cal., May 28,1884, and graduated from the University of California, College of Mines, in 1906. He joined the American Institute of Mining Engineers in 1916. During 1904 he was employed at the cyanide plant of the Buckeye mines, Forest Hills, Cal. In the autumn of 1909 he went to the Coeur d'Alene District, Idaho, and was first employed on construction work of the Bunker Hill & Sullivan Mining & Concentrating Co'., with a short intermission at the Hercules mill, after which. he was sampler and assayer for the Bunker Hill & Sullivan Co. until May, 1910, when he was obliged to return to California to attend to family interests. Returning to the Coeur d'Alene district in November, 1911, he was given charge of remodelling and operating the mill of the Coeur d'Alene Development Co., treating the output of the Ontario mine; this work he performed with credit and complete success. In December, 1914, he returned to the Bunker Hill & Sullivan Co., as assistant metallurgist and mill superintendent, his work consisting mainly in the testing and improvement of concentrator practice, which he continued with great credit until August, 1915, when family considerations required that he again return to the home of his parents at San Diego. Mr. Bailey was characterized by energy, both physical and mental, by devotion to his friends, associates and employer. He was particularly successful in his relations with the men under him and, in fact, was thoroughly well likcd by everybody with whom he came in contact.

Jan 1, 1920

By K. C. Kocsis

"Diesel-powered equipment has allowed the mining industry to raise production rates and significantly improve productivity, as it is rugged, mobile and reliable, but its widespread use in underground mines has generated concerns regarding the exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as diesel particulate matter (DPM), which has recently been classified as a human carcinogen by the International Agency for Research on Cancer. The agency expressed further concerns that workers’ exposure to high DPM concentrations can increase the risk of cardiovascular, cardiopulmonary and respiratory illnesses. Three emerging technologies could have the ability to replace dieselpowered equipment and remove DPM from underground mines: fuel-cell-powered mining equipment, battery-powered mining equipment and advanced material handling systems. This paper reviews them and assesses whether they have reached the point where the pollutants emitted by diesel-powered equipment can be removed from underground mines through the introduction of zero-emission mining equipment and power systems. Information is also provided from the results of a feasibility study, including a detailed cost benefit analysis, carried out at six Canadian and nine U.S. underground mines, which looked at the possibility of replacing diesel-powered production equipment with fuel-cell-powered equipment. The remarkable pace at which battery technology is progressing is also reviewed, and the feasibility of replacing diesel-powered mining equipment with battery-powered equipment is assessed. IntroductionHazardous pollutants in underground mines. Why is it important to remove diesel particulate matter (DPM) from underground mines? Over the past 40 years, diesel-powered equipment has allowed the mining industry to achieve rising production rates and major improvements in productivity, as the diesel engine is an economical source of power and diesel-powered equipment is usually rugged, mobile and reliable. On the negative side, the toxicity of some diesel exhaust gases is well known (Grenier et al., 2001), and the widespread use of diesel-powered equipment in underground mines has generated increasing concerns about the occupational exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as DPM. Diesel equipment also entails other hazards like heat and humidity. Exposure to excessive heat can cause heat illnesses, such as heat rash, heat exhaustion and heat stroke (Donoghue, 2004; Roghanchi et al., 2016), and a hot and humid underground environment negatively affects the efficiency of the workforce, which may result in a decline in production output (Roghanchi et al., 2017)."

Jan 10, 2017

By Westwater, J. S.

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W. within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleveland-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. A1len. Mather "A" shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather " B, " also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation.

Jan 1, 1949

By J. W. Reynolds

Introduction The Sullivan mine, at Kimberley, B.C., is the principal source of ore for the Consolidated Mining and Smelting Company of Canada, Limited. Current production amounts to about 2,500,000 tons of lead-zinc ore a year. With approximately 1,600,000 feet of percussion drilling and 700,000 feet of diamond drilling being carried on each year, any improvements in drilling practice are important. Testing of new equipment and drill bits is a major function of the Testing Department at the mine. Tungsten carbide bits have been the subject of many tests since 1947 and have been used in operations since 1948. This paper details with the methods of testing and gives comparative data on performance and costs for tungsten carbide bits as compared to steel bits. Operational use of tungsten carbide bits started in April, 1948, and the extent of application has increased considerably since that time. The scale of employment is illustrated in Table I, which also shows other statistics on the use of carbide bits. Up to the present time eighteen types of carbide bits or tipped steel, as made by six different manufacturers, have been tested. In general, one supplier's bits have been used in operations, but some large-scale operational tests have been carried out with other types. The types tried are shown in Table II. To date they have been, the subject of 33 tests, covering the destruction of 804 bits over an observed footage of 42,586 feet.

Jan 1, 1951

By Alfred Petrick

This report analyzes the byproducts systems of lead, zinc, uranium, rare earths, iron, aluminum, titanium, and lithium. Specific byproduct metals covered are cadmium, germanium, indium, and thallium from the zinc system; antimony and bismuth from the lead system; vanadium, radium, and scandium from the uranium system; rare-earth oxides from the rare-earth system; and cobalt, gallium hafnium, and rubidium from other systems. The report discusses various metallurgical systems, marginal and incremental production costs of byproduct subsystems, industry structure and organization, and historical data on price, consumption, and supply.

Jan 1, 1973

By Games Slayter

NO reasonably well-informed person believes that the role of minerals, both metallic and nonmetallic, will be any less important in the future than it has been in the past. The contrary is true. Industrialization is based on mineral resources and man's ability to make use of them. A nation's standard of living, its political and military power, will continue to depend largely upon the extent to which it is industrialized-and minerals are the raw materials both of the machine and the power to run the machine. Minerals are also the raw materials of human health and stamina. The world's healthiest, most vigorous, and most long-lived peoples have always been those that have lived in regions of the globe where the earth is rich, and kept rich, in the phosphates and other minerals required for the production of the so-called growth foods. Only a small proportion of the land surface of the globe is suitable under any circumstances for large-scale production of these and other essential foods. As things stand, only a part of this land is capable of such production either because the soil minerals have been exhausted by cultivation, or because they never existed in the soil in sufficient quantities.

Jan 1, 1943

By S. Vennos

As a result of Synopsis 73-16 Dynadyne responded with an unsolicited proposal offering the Bureau of Mines to develop an ultra-low volume coal mine dust personal sampler. In the ensuing technical discussions the choice of a desirable volumetric rate became a focal point. While, the initial proposal was based on a volumetric rate in the area of 50 cc/min the Government expressed interest in a variety of mass flow rates ranging from 50 cc/min to 2000 cc/min. The physical characteristics such as weight, volume and configuration of a personal sampler are to a large extent - dependent on the operating volumetric rate. It became readily apparent that the optimum size of such an instrument as a function of volumetric rate was not known and that a study of the choice of optima was essential prior to beginning the development, Hence, the Government authorized a two phase approach to this project. Phase I was to include a Technical Evaluation Study of optimum characteristics in the range between 0. 1 to 2. 0 lpm. Based on these findings and in consultation with MESA personnel, the Bureau of Mines was to authorize the second phase that is, the development. Phase II, was to include the drawing of a set of performance specifications stating among others the desired operating volumetric rate. In this report, every effort was made not only to present the actual work done over the course of this development, but to reflect also our engineering "thinking" providing answers as to the "why" we preferred certain solutions over others. We believe that this added dimension is not only useful for the Government official evaluating this report, but also that the Government is entitled to it providing the official with an educational content useful in avoiding future costly repetitions of similar situations.

Jan 1, 1975

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By R. A. L. Drew, G. Mendoza-Suarez, J. Filipi, R. Vintila, J. A. Kozinski

Economics and environmental considerations along with the increasing demand of hydrogen encourage development of novel technologies such as plasma processing of hydrocarbons and thermal cracking of natural gas. Plasma discharges, either in thermal or non-thermal regimes are expected to allow low temperature and fuel flexible on-site hydrogen generation. The main drawback of thermal plasma reformers is the high-energy consumption resulting from high-temperature operation. On the other hand, non-thermal plasma, generated by dielectric barrier discharge (DBD), is able to simulate the chemical reactions employing much lower energies than those required by thermal treatment processes. The non-thermal plasma process allows for instance, a direct conversion of methane into hydrogen and carbon black with no CO2 release. The focus of this research was on the GHG-free method of H2 generation in compact non-thermal plasma reactors using low, medium and high permittivity dielectric ceramics. A stable, non-thermal plasma was generated by placing a dielectric ceramic between two electrodes with a 25 thou gap and applying an alternating current of 1-5kHz and voltages of 4-8kV. In order to ensure energetic efficient plasmas, experiments were conducted to analyze the behaviour of different permittivity ceramics. It was found that the dielectric properties of a ceramic, when used in a DBD reactor, have a strong influence on the discharge characteristics, which in turn influence the power consumption. Higher dielectric constant resulted in higher conversion rates of methane (higher yield of hydrogen and carbon). At the same time, the mechanical properties of the dielectric material, which are closely associated with its processability, influenced its resistance to electron bombardment, as well as thermal and mechanical damage. Therefore a reliable ceramic should have good dielectric properties, in addition to good thermo-mechanical stability.

Jan 1, 2004

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963

By Peter W. Lipman

In the Rocky Mountain region, variations in Tertiary mineralization correlate with changes in tectonic setting and associated igneous activity that can largely be related to tectonics along the west boundary of the American plate. Successive settings include compressional tectonics and associated continental-arc igneous activity; transitional igneous types associated with intra- and back-arc extension; and basaltic or bimodal basalt-rhyolite assemblages associated with Basin and Range extension in- ward of a growing transform boundary between Pacific and American plates.

Jan 1, 2013

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By A. Fahr, T. Byczkowski, M. Genest, C. Mandache

"Layered aluminum structures assembled with rivets are often found in aircraft fuselage. These structures are exposed to various mechanical loads and a range of environmental conditions that contribute to their ""aging"". The rivet holes are the source of stress concentrations and the location of crack nucleation and growth. Detection and sizing of second and third layer cracks under fasteners represent a major challenge for non-destructive evaluation (NDE) technicians. Electromagnetic methods are currently the most feasible NDE techniques that are capable of successfully inspecting such structures. However, different probe lift-offs, due to protruding rivets and paint coatings, or interlayer separations, due to sealant or air gaps, pose difficulties in detecting and sizing cracks. In addition, the use of conventional eddy current technique is limited due to the inverse relationship between the probe spatial resolution and its field penetrability. In this paper, we present an alternative approach that overcomes the previously mentioned shortcomings by using pulsed eddy current excitation and magnetoresistive sensor pick-up. Various signal manipulations are employed for defect detection and quantification."

Jan 1, 2006

By Allan H. Caverson

Over the past nine years a means for measuring the distance between the mine roof and floor has been developed at the White Pine Mine which yields relevant information utilized in the mining operation. The technique known as "convergence!' is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity, and overall mine stability. From a limited introduction in 1964 related to monitoring an experimental longwall project, the activity of convergence measurements has been expanded to become a production tool now found in all sections of the mine. Presently, the program involves four main types of activity: 1. Monthly measurements in areas known to be active, and in sample blocks scattered throughout the mine for a long-term stability study. 2. Semi-monthly measurements along vital travel roads, belt drifts and compressor sites. 3. Weekly measurements in areas where men are working. 4. Daily measurements in pillar-recovery and caving operations. Today, one field engineer and six technicians are involved full time in convergence work. Rock Mechanics technicians have installed approximately five thousand stations since the start of the program and of this number, over twenty-five hundred active stations still comprise the mine-wide network spread over the more than five square mile extent of the White Pine Mine workings.

Jan 1, 1973

By Piyush K. Dutta

This report describes the design, development and manufacture of production stoper drills and results of their field tests, it is shown that underground stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using these pneumatic drills. The design concept of these drills is a radical departure from the standard valved rifle bar type drill machine design to a drill featuring a valveless independent rotation system, use of an integral muffler and a shroud tube. Six drills were manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1983