Search Documents

By Lawrence P. Goldfarb

This paper presents the results of the geotechnical investigation for the repair of the Fashion Island Boulevard Bridge, Bridge No. 350160, in San Mateo, California. The concrete, precast girder bridge suffered considerable damage during the Loma Prieta earthquake. The existing 36-inch, precast, prestressed concrete piles cracked and spalled at their tops. Based on analyses performed by Biggs Cardosa Associates, structural engineers, the piles did not have sufficient strength and ductility to resist the dead plus seismic loads specified in the Caltrans "Bridge Design Specifications". Additional support for the bridge was needed and the repair strategy consisted of installing large diameter pipe piles at the existing bent and abutment locations. This paper describes the geotechnical engineering analysis and design decisions for the large diameter pile design.

Jan 1, 1993

By R. W. Raymond

THIS meeting was held in the new home of the Institute, the United Engineering Society Building, 29 West 39th Street, New York City, directly following the Dedication ceremonies. The first session was held in the large Auditorium, Thursday, April 18. The meeting was called to order by Mr. John Hays Hammond, President of the Council, who said Before taking up the reading and discussion of papers, I will call upon Dr. Rossiter W. Raymond, the oldest living past-President of the Institute, who has been in harness almost continuously for thirty-six years, and who has contributed more than any one else to bring this society to its present great success and to establish the reputation of the American mining engineer the world over, for a few words supplementary to those which were uttered to engineers generally, during the sessions of yesterday and the day before. ADDRESS BY R. W. RAYMOND. The generally accepted Darwinian doctrine of the survival of the fittest is sometimes illustrated by persons who are supposed to be the fittest because they have simply survived. I fear that I come under that category. Almost all of my contemporaries in the early history of this Institute have passed away. Only one or two of the original founders remain, and I may fairly say that scarcely any remain who were active at that : time in shaping the organization and the future career of the Institute. In May, 1871, I was thirty-one years old. Next week I shall be sixty-seven years old. All the intervening years have been devoted to the service of this Institute almost continuously, either as President or Vice-President or Secretary. You may easily imagine, therefore, with what pleasure I greet you on this occasion. I am not here to extend to you the welcome of the City - of

May 1, 1907

By Charles H. Foreman

This paper describing the mining practice of the Hecla and Star mines, both located at Burke, Idaho, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. It is partly a revision of articles by the author appearing in volume 72 of the Transactions of the American Institute of Mining Engineers, published in 1925, and in the June 1928, issue of the American Mining Congress Journal. About 26,000 tons per month of lead ore is produced at the Hecla mine. Costs at the mine are given for the year 1928. Stoping operations in the Star mine have covered such a short period, during which time the abnormal expenses of starting were incurred, that they are not given in this paper.

Jan 1, 1930

By Ralph H. Whaite

In undermined urban areas, new solutions to subsidence problems are being sought. The Bureau of Mines is investigating a hydraulic backfilling technique whereby fill material is pumped as a slurry through a closed system and widely distributed in inaccessible mine workings from a single borehole. A full-scale demonstration was completed in 1973 in Scranton, Pa., which is underlain by abandoned anthracite mines in several coalbeds superposed one above another. A 30-acre residential area was stabilized by injecting about 450,000 cubic yards of crushed mine refuse into two coalbeds through five injection boreholes. Nearly 200,000 cubic yards was injected through one borehole from which the material moved into the mine workings on all sides; the injected material reached a maximum lateral distance of 640 feet and filled mine openings from floor to roof. In the gravity-feed method formerly used to backfill inaccessible mine workings, quantities of fill injected per borehole averaged about 300 cubic yards. The gravity-feed method required many closely spaced injection holes and provided incomplete filling. The new method, designed for inundated mines, proved successful also in mine workings about mine-water pool level. Distribution of slurry through a buried pipeline minimized disturbance to the community.

Jan 1, 1975

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By W. L. Dare

This paper is one of a series being prepared by the Bureau of Mines on the methods and costs of mining uranium on the Colorado Plateau. The Continental No. l mine is at the south end of the Big Indian mining district, San Juan County, Utah. The mine is on a school section owned by the State of Utah and leased by Continental Uranium, Inc. A 70,000-ton uranium-vanadium ore deposit was discovered as a result of an exploratory drilling program completed in 1954.

Jan 1, 1957

By V. A. Nieberlein

Problems of design involving the high-temperature characteristics of materials of construction have focused attention on tungsten, the metal with the highest melting point. To study the properties of this metal a method was needed to produce tungsten of high purity easily and consistently. The Bureau of Mines has made tungsten metal in massive form on a laboratory scale by hydrogen reduction of tungsten hexafluoride (WF6). Metal made in this manner had a purity of 99.99 percent or better, with reference to all detectable impurities, including gases. The process tolerated a wide variation in operating conditions, and the results with respect to total impurities as low as 0.01 percent were reproducible.

Jan 1, 1959

As has been the case since the early Phoenician traders, the minerals used by modern man come from deposits scattered around the globe. The price received is more and more being set by worldwide supply and demand. Thus the price component in the profit equation:Profits = Material sold (units)x(Price/unit û Cost/unit) is largely determined by others. The recent price history for two of the major metals, copper and iron, are given in Figures 1 and 2, respectively. As can be seen there has been a steady decline in the prices (when expressed in constant dollars) over the 20 years which have lapsed since the first of the International Conferences on Mass Mining, æDesign and Operation of Caving and Sublevel Stoping MinesÆ was held. If one would look back over the entire 20th century this would also be the trend. Cost containment/reduction through efficient, safe and environmentally responsive mining practices is serious business today and will be even more important in the future with increasing mining depths and more stringent regulations. A failure to keep up is expressed very simply as: Profit This, needless to say, is unfavourable for all concerned (the employees, the company, and the country or nation). The mining companies have had to look at ways of reducing the expense part of the profit equation while maintaining safe, environmentally conscious operations. Table 1 summarises the rules for working in todayÆs economy.

Jan 1, 2000

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By Malcolm Black

Introduction The circumstances under which the gold mining industry was forced to curtail operations a few years ago are well known to all. The effect of those circumstances is particularly noticeable when one enters some of the larger mills that were designed, in better times, to treat relatively large tonnages. On their grinding floors one will observe that a number of grinding units are lying idle, and the ravages of rust are everywhere in evidence. The same applies to other equipment throughout these mills. In 1941, we found it necessary to reduce tonnage considerably in the Wright-Hargreaves mill. With the assumption that a lower tonnage would be of long duration, we began to focus our attention on some of the idle equipment with a view to re-arrangement of the flow-sheet for greater economy of operation. In an article by the writer published in the Engineering and Mining Journal (March, April, and May issues, 1939) , it was pointed out that in designing this mill there was a very limited floor space available. The choice of thickening equipment was imposed solely by the necessity for space: conservation. Thickening by gravity would have required 5,000 square feet of floor space, whereas Genter thickeners required only 1,200 square feet. As a consequence, the Genters were chosen. The decision to add flotation to the circuit was made primarily to save space. On a cost-plus-tail basis, 80 to 100 hours agitation on all pulp would produce similar overall results, but would require much more space.

Jan 1, 1948

By R. Bonifaz, R. Subiabre

The Chagres Smelter, part of the Anglo American plc group, situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant review of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studied various options for investment that will yield a suitably profitable business to benefit both Anglo American and Chile. The most relevant technical indicators are: energy consumption=6,3 GJ/ton fine copper (1st in the world), intensity of smelting rate in Flash Smelting unit of 6,900 ton of copper concentrate/m2 of furnace area (1st in the world) and to be one of the top five smelters in achieving the lowest direct cash cost .

Jan 1, 2007

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

By James D. Hall

THE Dome ore-bodies are more or less isolated and are mined. by shrinkage stoping. An interwoven system of veins is mined at Hollinger '.1.nd requires close filling. Deep mining is the problem at McIntyre. Dome ore contains a large amount of free gold, which is recovered on blankets. An all-cyanide flow-sheet is \lSed in the Hollinger mill. Flotation concentration is an important feature of McIntyre mill operation. Therefore, these three mines afford an unusual opportunity to compare gold mining and milling methods. The purpose of this paper is to describe the conditions existing at the Dome, Hollinger, and McIntyre mines and to outline the mining and milling practice at each property. Figures 3, 4, 5, and 7 are reproduced from the Canadian Mining ]011rna/, September, 1935 (Young, A. W., Mining at Hollinger), and Figures 8 to 11 from the Engineering and Mining Journal, November, 1933 (Keeley, D. E., Development and Mining at McIntyre). The photographs (Figures 6, 12, and 13) are by The Canadian Government Motion Picture Bureau. Diagrams of the several mill flow-sheets, which formed a part of the original paper, are not reproduced here. They will be found in Dorr's Cyanidation and Concentration of Gold and Silver Ores.

Jan 1, 1938

By Don Belsher

Work on contract H0272007 is summarized for the period of 1 February 977 to 1 February 1978. The initial evaluation of two potential systems for the location of well casings, voids, and tunnels in coal are described. The pulse measurement equipment used for the evaluation of the antennas selected possible use with a pulse time domain system and an FM-CW system is described. A TEM horn antenna design potentially suitable for use with these systems is given. An operational comparative analysis between various antenna types is presented.

Jan 1, 1978

By Jr. Raleigh

As part vi the development of the Coal Quality Expert (CQRN) --a computer program capable of predicting the impacts of coal quality on power plant performance, costs, and emissions control--several nationally important coals are being characterized to augment the coal quality database associated with the software. The project is sponsored by the U.S. Department of Energy and the Electric Power Research Institute (EPRI) under the Clean coal Technology Program. Since 1989, CQ Inc. (a subsidiary of EPRI) has characterized seven bituminous coals from Alabama, Illinois, Kentucky and Oklahoma and six sub-bituminous coals from the Powder River Basin (PRB) in Montana and Wyoming. Coals from the PRB region--being burned more frequently in Midwestern and southern power plants to reduce emissions of sulfur oxide compounds--can sometimes contain significant concentrations of potentially toxic elements. Although no limits were imposed on air toxics emissions from fossil-fuel fired utilities by the Clean Air Act Amendments of 1990, future regulations may be implemented at the conclusion of Federally-mandated emissions studies. One possible result is that any increased utilization of coals, including those from the PRB, may depend on the potential for removing toxic trace elements prior to combustion.

Jan 1, 1993

By N. B. Strydom

I have read with interest all the papers dealing with heat transfer and the setting of heat stress limits that have appeared during the past two decades. Scientifically speaking, most of them can be rated as being of a high standard, and some of them have been acclaimed internationally as masterpieces of logical and calculated reasoning. Weathering of ore minerals A short course on 'The Weathering of Ore Minerals and the Textural Evaluation of Base Metal Gossans' is to be given by Dr I.M. Reynolds in Grahamstown from 4th to 6th October, 1982.

Jan 1, 1982

By Janos de Warga

"After a short introduction to the history of the semi-conductor theory, the paper describes the principles of electron and hole flow in the semiconducting materials, the operation of the PN junction, and the rectification process in multi-layer devices (diodes and SCR's). The various methods of purification and zone-refining of the silicon are illustrated prior to the discussion on the most commonly used junction-forming processes (alloying, diffusing, etc.). Modern device fabrication and packaging operations are illustrated. Factory testing, evaluation, electrical parameters and guaranteed rating characteristics are listed. It is explained in this paper how the various device parameters affect the electrical performance of the finished unit and how the finished unit characteristics (turn-on, turn-off time, etc.) will influence the equipment rating. In concluding, some typical items of equipment are highlighted, and the applications of these semiconductor rectifiers in the chemical, mining, pulp and paper, and steel industries, etc., are dealt with."

Jan 1, 1967

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963