Search Documents

By A. R. Khodabandeh, T. Nematkhah

Correct selection of forging parameters is very important to produce sound superalloy parts. In this investigation nickel-iron base superalloy IN901 successfully forged and seal spacer, which is a part of airplane with about 11 kg weight has been produced. Forging has been performed on the basis of hot compression results, which show deformation above 1100°C associated with dynamic recrystallization (DRX) which can increase the workability of material. On the other hand annealing at 1100°C decreases the flow stress during hot compression, and then increases the material formability. Then billets annealed at 1100°C in electrical furnace for 24 hours and reheated again to 1100°C before forging. Initial square cross section billet with 128mm side and 202mm length forged immediately after reheating by 80MN mechanical press. Specimens forged in five steps: upsetting, three steps molding and finishing. Preformed and molded specimens reheated in electrical furnace before later step of forming. Finally specimens trimmed by 1 OMn mechanical press and hot set by hydraulic press and then cooled in air to room temperature. Results show that reheating temperatures has been selected correctly because there isn't any surface crack and die cavities filled completely by forging material. Material flow has been carried out properly and there isn't any defect in critical points especially in extradoses and intradoses. Microstructural examinations show that grain boundaries contain Ti-rich globular particles that formed during cooling.

Jan 1, 2006

By M. G. Fowler

A GENERAL decline in copper production for most American producers occurred during the past year as a result of shortage in available labor. Few noteworthy technical developments have been reported; undoubtedly, many changes and improvements have been made but have not been reported because of lack of time. During the war years through 1944 the pressure for sustained high production has been of prime importance and during 1945, with slackening of production, many operators were faced with the problem of catching up on repairs and maintenance of plants, with inadequate labor supply. In hydrometallurgy there were some important developments that undoubtedly will be reported during 1946. Several operators in the Southwest have instituted experimental leaching programs to exploit low-grade oxidized and mixed ore bodies. The Bureau of Mines is conducting pilot-plant experimental work to determine the possibility of producing a satisfactory sponge iron at an attractive cost from deposits of iron ore and coal in Arizona. The sponge iron would be used for the production of cement cop¬per. The cell house of the Inspiration Consolidated Copper Co. at Inspiration,

Jan 1, 1946

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Whitman E. Brown

"As part of a Nation-wide program of the United States Government to develop natural resources, funds were made available to the Bureau of Mines for the investigation of the ""Reduction of Iron Ores by Solid and Gaseous Fuels."" These investigations are concerned with the direct production of iron from its ores without the use of a blast furnace. Many processes have been proposed for the low-temperature reduction of iron oxides, but few have been developed to commercial use. High-quality sponge iron is produced com-mercially only in Sweden.The cost of iron production depends in part on the grade of the ore and increases with decrease in grade. The substitution of cheap natural gas in a sponge-iron process for expensive coke in smelting in the blast fry pace would partly compensate for the use of low-grade ores. If a process can be developed in which inexpensive natural gas can be used as fuel and reducing agent, the large deposits of low-grade iron ore and the natural-gas resources of east Texas may be utilized in the commercial production of sponge iron.Sponge iron may possibly be used to supplement scrap iron, pig iron, or, in special instances, wrought iron. Sponge iron will vary but slightly in composition and will contain little or no nickel, cobalt, manganese, copper, and other allowying metals. It is becoming increasingly difficult to obtain choice scrap iron of nonalloy composition. Pig iron contains 1.5 to 3.0 percent silicon and 3.0 to 4.5 percent carbon. Sponge iron generally contains less carbon than pig iron.The Madaras Steel Corp. in Longview, Tex., built a set commercial-scale sponge-iron plant which was intended to be operated in connection with a steel foundry. The process is based upon the reduction of preheated iron ore, with hot reducing gases under pulsating pressure. Although the Madaras Corp. had previously experimented with the production of sponge iron by reducing the ore with pure hydrogen, several attempts to use a re-formed natural gas as the reducing agent in this pilot plant were unsuccessful. The Bureau of Mines leased this plant and conducted an extensive investigation of the Madaras process on a semicommercial scale.The experiments were not entirely satisfactory, partly because of mechanical difficulties and partly because the reducing gas was not of the best quality. However, much information on the production of reducing gas by re-forming natural gas and on the reduction of iron ore with re-formed natural gas was obtained.The sponge iron produced contained approximately 0.1 percent phosphorus; and, after melting in an electric furnace, the iron contained approximately 0.15 percent phosphorus. The results of attempts to improve the ore by ore-dressing methods were not encouraging."

Aug 1, 1946

By Diego Quiroz, Francisco Cuellar

Existen tareas esenciales como la exploración, inspección, y digitalización de galerías subterráneas que pueden presentar un alto riesgo para los trabajadores ya que se pueden producir accidentes. En este contexto, se hace necesario buscar soluciones más eficientes y seguras para la exploración, inspección, y digitalización de galerías subterráneas en la industria minera. Se propone como solución el uso de un robot terrestre no tripulado capaz de desplazarse en superficies irregulares para la digitalización, inspección, y diagnóstico recurrente y seguro de la infraestructura de galerías subterráneas en minería.

Sep 29, 2023

By FLOYD T. TAYLOR

IN 1833, less than one hundred years ago, Michael Faraday discovered and stated the laws of electrolysis. His discovery formed the foundation of a new use of metals which has now reached a variety of application not ordinarily appreciated. Furthermore, things can be done with electro-deposited coatings which have thus far defied other methods. Some of the uses of electro-deposited coatings are interesting. The tonnage of metals already finding an outlet through such a channel is considerable. In general electro-deposits have two characteristics: ornament plus utility; utility plus ornament. Both these factors are usually found associated in electro- deposits. Ornament plus utility was probably the first use. For example, the silver-plating of tableware, having its real birth in Birmingham, England, about 1844. However, this same ornament plus utility retarded the development of electro-plating, because in the beginning, electro-plated articles were branded with the odium of imitation and shunned accordingly. The gold brick of the swindler may be an exception to this statement.

Jan 1, 1929

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By Casters B. Foster

The U.S. Department of Energy has undertaken, in a cost sharing partnership with industry and utilities, an extensive coal-oil mixture (COM) combustion program in a number of promising applications. One of these is the injection of COM through tuyeres into a blast furnace in lieu of oil. From work done previously, it has been established that COM can be burned in existing oil, fired facilities. The issues being addressed by the current DOE program are: 1) determination of best available technology to achieve environmentally acceptable operation, and 2) determination of applications for which COM can be utilized economically.

Jan 1, 1978

By Gustav Egloff

AN unexpected and unprecedented demand for its products now challenges the petroleum industry. Between 1939 wand 1946, domestic oil demand increased nearly 45 per cent and in the first half of 1947 it was 10 per cent higher than in 1946. In 1939 the United States produced 1,264,962. 000 bbl of crude oil and indications are that about 1,860,000,000 bbl will be produced in 1947, a 47 per cent increase. Runs to stills are more than keeping pace with production. The crude capacity of 365 operating refineries is rated as 5,400.000 bbl daily and almost 100 per cent of this capacity was running crude oil in August 1947. The oil industry is cognizant of our need for a greater volume of petroleum products and is expending the huge stun of four billion dollars on exploration. production. transportation, refining. and marketing of petroleum. Of this amount about half will be spent on exploration and production. a billion on refining. and another billion on transportation and marketing facilities.

Jan 1, 1947

By Ramarao Inguva

Feasibility studies being conducted to investigate the use of electromagnetic methods for insitu volumetric heating of oil shales will be discussed. A two dimensional numerical model which describes eletromagnetic heating of oil shales is outlines. The model includes equations for temperature, pressure, saturations, chemical reactions, mass conservation, and source terms. The gases are all assumed to form one bulk species and the oil is assumed to remain in liquid form. The chemical reactions include pryolysis of kerogen and char, release of bound water, coking, and decomposition if carbonates. Porosity and permeability are dynamic functions of the organic materials. Calibration of the model is accomplished by comparison of the model results with experimental data obtained by IITRI. Nonlinear relationships for viscosity, thermal properties, and source terms and used as inputs to the model. A finite difference approximation to the differential equations is derived and solved using Newton's iteration technique. For the cases studied the solutions are quite stable. Numerical resultes are included and a preliminary study of the optimization of the heating process is presented.

Jan 1, 1984

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Archer E. Wheeler

IN the copper industry, the year 1942 was one of striving for larger tonnage and increased production. The demands of the war program placed copper high in the list of strategic metals and the Government encouraged production by offering a premium of 5c. per pound for copper output in excess of the 1941 quotas. This had the effect of increasing the tempo of existing operations and also of initiating a number of projects which will eventually result in production from sources not hitherto exploited. No radically new methods of copper reduction were reported.

Jan 1, 1943

By L W. Morley

The Division is concerned with physical methods as applied to geo-logical research and mapping. An at-tempt is made to describe long-term goals, illustrated by examples of projects in the fields of aeromagnetic interpretation, palaeomagnetic re-search, Pleistocene and groundwater geophysics, seismic surveying, electromagnetic research and instrument development. Cooperative projects in surveys and research, with universities, private companies and provincial organizations, are frequently undertaken. An outstanding example of this is the recently approved Federal-Provincial Aeromagnetic Survey Plan, the purpose of which is discussed both from an economic and a scientific point of view. HISTORY OF THE DIVISION M AGNETIC, electrical, seismic and gravity methods, as a means of extending the geologist's sphere of observation beyond the head of his hammer, came into wide-spread use for the first time after World ?war I. Interest in these methods was aroused amongst geologists of the Geological Survey and, in 1928, a group of these geologists and university

Jan 1, 1963

By JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Dionissios T. Hristopulos, Zach Agioutantis

Methane gas is emitted during both underground and surface coal mining. Underground coal mines need to monitor methane gas emissions to ensure adequate ventilation is provided to guarantee that methane concentrations remain low under different production and environmental conditions. Prediction of methane concentrations in underground mines can also contribute towards the successful management of methane gas emissions. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the USA. The AMS data were stored and pre-processed using an Atmospheric Monitoring Analysis and Database Management system. Furthermore, different statistical dependence measures such as cross-correlation, autocorrelation, cross-covariance, and variograms were implemented to investigate the potential autocorrelations of methane gas as well as its association with auxiliary variables (barometric pressure and coal production). The autoregressive integrated moving average (ARIMA) time series model which is based on auto-correlations of the methane gas is investigated. It is established that ARIMA used in the one-step-ahead forecasting mode provides accurate estimates that match the direction (increase/decrease) of the methane gas emission data.

Aug 2, 2022

By E. C. Roper

THE Britannia Mining & Smelting Company, Limited, have been operating their property at Britannia Beach, B.C., continuously for nearly forty years and have mined over 33,000,000 tons of ore from orebodies within a belt of highly sheared rocks, five miles long by 2,000 feet wide. The property is in the Coast Range mountains, about twenty miles due north of Vancouver. The mountains rise abruptly from sea level to elevations of 4, 500 feet within a horizontal distance of 7,000 feet. The topography has enabled the orebodies to be developed by adit tunnels. The active mining levels are connected to the adits by incline and vertical service shafts. The main service adits are the 2200, 2700, and 4100 levels (see Figure 1). The mine surface shops, three bunk-houses, and over one hundred dwellings form the townsite camp at the portal of the 2200 level adit. A small camp of one bunk-house and a few dwellings is situated at the 2700 level portal. The beach surface shops and camp, adjacent to the 4100 level adit, service the mill, foundry, and other beach installations as well as the mining from the 4100 level. The ore mined from the various orebodies is delivered to the 4100 main haulage level through a system of rock raises and intermediate tramming levels and is hauled on the 4100 level to the mill.

Jan 1, 1945

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

Demand for primary aluminum ingot increased during February, and several producers temporarily suspended new bookings for ingot. Alcoa announced that it would restart a potline at its Warrick, IN aluminum smelter by April 1, 1979, increasing the operations of that plant to its full capacity of 290,000 tons per year. At the end of February, it was reported that Alcoa would reactivate two of the seven units at its idle Point Comfort, TX smelter in May 1979, increasing the company's annual capacity by about 60,000 tons.

Jan 1, 1979

By G. W. Elger

This report describes pilot-plant studies and an economic evaluation of a process developed by the Federal Bureau of Mines, Albany Metallurgy Research Center, to produce synthetic rutile from a rock-type ilmenite concentrate. In this process, ilmenite blended with coke and lime is smelted in an electric arc furnace to separate most of the iron as salable pig iron and to form a titania-enriched slag of low iron content, which is treated with oxygen and titanium pyrophosphate. The titanium oxides are converted to crystalline rutile; the phosphate glass contains most of the associated impurities. The treated slag is ground and leached with sulfuric acid to liberate rutile crystals, which are concentrated by physical methods. In pilot testing conducted to obtain data for a cost estimation, a synthesized product containing about 88 wt-pct TiO2 and less than 2 pct FeO was extracted from a rock-type ilmenite concentrate containing about 45 wt-pct TiO2. The estimated fixed capital cost (on a mid-1975 basis) of a plant producing 500 tpd of synthetic rutile is $28,290,100. Based on 330 operating days per year, the estimated operating cost for this process is $351 per ton of synthetic rutile. The estimated selling price of synthetic rutile made from rock-type ilmenite is $344 per ton, based on a credit of $160 per ton of pig iron and a 20 pct interest rate of return on investment after taxes.

Jan 1, 1976