Search Documents

By M. M. Hassan

This report describes the analysis tools developed at West Virginia University which can be implemented to optimally design coal mine electrical systems. The basic analytical tools for all power systems are the load-flow and short-circuit analysis. Well known programs have been developed for analysis of ac transmission and distribution systems, but they are not applicable to a system which has combined ac/dc distribution, such as a coal mine power system. Furthermore, the topology of a coal mine electrcal system changes continuously due to the movement of the locomotives on the track. In the first section of this report, algorithms for carrying out load flow and short-circuit analysis of a coal mine electrical system are described. Results from the study of a typical coal mine system are presented. In the second section a method is described to optimally size power cables for cyclic loads. The method is based on the development of a thermal-electric model for a low-voltage power cable. Results from experimental verification of the model are also presented. These techniques are useful in the safe, efficient, reliable and economical design of the coal mine electrical power systems.

Jan 1, 1979

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, C. J. Malanga

There is evidence to suggest that cell injury induced in alveolar macrophages (AM) following phagocytic activation by silica particles may be mediated through changes in intracellular free calcium [Ca 2+}. However, the mechanism of silicainduced cytotoxicity relative to [Ca2+], overloading is not yet clear. To provide a better insight into this mechanism, isolated rat AMs were exposed to varying concentrations of crystalline silica (particle size< 5 µm in diameter) and the fluctuation in their [Ca2+]; and cell integrity were quantitatively monitored with the fluorescent calcium probe, Fura-2 AM, and the membrane integrity indicator, propidium iodide (Pl). Results from this study indicate that silica can rapidly increase [Ca2+]; in a dose-dependent manner with a characteristic transient calcium rise at low doses (<0.1 mg/ml) and an elevated and sustained rise at high doses (>0.1 mg/ml). Depletion of extracellular calcium [Ca 2+]0 markedly inhibited the [Ca2+]; rise (˜90%), suggesting that Ca2+ influx from extracellular source is a major mechanism for silica-induced [Ca2+]; rise. When used at low doses but sufficient to cause a transient [Ca2+]; rise, silica did not cause significant increase in cellular Pl uptake during the time of study, suggesting the presevation of membrane integrity of AMs under these conditions. At high doses of silica, however, a marked increase in Pl nuclear fluorescence was observed. Depletion of [Ca 2+] 0 greatly inhibited cellular Pl uptake, induced by 0. 1 mg/ml or higher doses of silica. This suggests that Ca 2 + influx, as a result of silica activation, is associated with cell injury. Indeed, our results further demonstrated that the low dose effect of silica on Ca 2+ influx is inhibited by the Ca2+ channel blocker nifedipine. At high doses of silica (>0.1 mg/ml), cell injury was not prevented by nifedipine or extracellular Ca2+ depletion, suggesting that other cytotoxic mechanisms, i.e., nonspecific membrane damage due to lipid peroxidation, are also responsible for the silica-induced cell injury. Silica had no significant effect on cellular ATP content during the time course of the study, indicating that the observed silicainduced (Ca2 ... ); rise was not due to the impairment of Ca2 + -ATPase pumps, which restricts Ca2+ efflux. Pretreatment of the cells with cytochalasin B to block phagocytosis failed to prevent the effect of silica on [Ca2+]; rise. Taken together, these results suggest that the elevation of [Ca2+]; caused by silica is due mainly to Ca2+ influx through plasma membrane Ca2+,channels and nonspecific membrane damage (at high doses). Neither ATP depletion nor Ca2+ leakage during phagocytosis was attributed to the silica-induced [Ca2+]; rise.

Nov 1, 1995

By K. Mayhew, K. Murray

The CESL Copper Process was developed as a hydrometallurgical alternative to smelting and refining for copper sulphide concentrates. As the majority of such concentrates contain appreciable gold and silver values, effective recovery of these metals is essential to the economics of this technology. Unfortunately, conventional cyanide processing cannot be used on the residue from the copper process, clue to its unusual characteristics when compared with naturally occurring gold and silver ores. An abundance of elemental sulphur, as well as the presence of cyanide soluble copper, leads to the formation of both thiocyanate and copper cyanide which is detrimental to process economics clue to excessive cyanide consumption. This, however, can be reduced to acceptable levels by process innovations such as pressure cyanidation and cyanide recovery. This paper outlines the successful application of the CESL Gold Process to various gold-bearing copper concentrates from bench to demonstration scale.

Jan 1, 2011

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By Jimmie C. Rosenbruch

The Federal Bureau of Mines evaluated the prospects for using geothermal energy to generate electricity for mines in remote areas. Given the development of a geothermal resource for this purpose, the subsidiary uses of space heating and agriculture were then examined to see if other industries might be viable given a cheap source of heat energy. Sites investigated were located in three areas of Alaska: Kobuk in the northwest, Unalaska in the southwest, and Stikine River in the southeast. Each site was relatively close to mineral deposits whose prospects for development would be enhanced with cheap power.

Jan 1, 1975

By Jason Baird, Joshua Hoffman, Phillip Mulligan

The purpose of this report is to address the method of reducing the overall explosive weight of Explosively Formed Projectiles (EFPs) while still achieving satisfactory performance. This reduction is crucial in order to comply with outdoor explosives testing standards for Missouri University of Science and Technology’s (Missouri S&T’s) Experimental Mine. Initial EFP design testing exceeded given limitations, making reliable data difficult to ascertain. EFPs must be tested outdoors to allow for specific information recordings which aid in defending against them.

Jan 1, 2010

By M. E. D. Raymont

"During the history of the sulphur industry there have been three distinct phases of production. Factors controlling supplies during these periods have shifted from demand for sulphur to demand for energy and a cleaner environment. The pattern of brimstone production is t raced through these phases and includes estimates of future supply; these indicate an involuntary excess production of some 20 million plus tons per year by 1980 unless some large-scale new uses are found. Traditional uses for sulphur, including fertilizer, chemicals, fibers, etc., are generally expanding slowly; how• ever, supply in ""by-product"" form alone will soon outstrip demand. The predicted oversupply situation can be corrected by the development of novel potential markets. Promising areas include construction materials, insulation and plastics, among others."

Jan 1, 1972

By Z. A. Zhou

In Canadian oil sands processing, flotation is used to recover liberated bitumen droplets from oil sands slurries. Similar to conventional mineral flotation practice, a fundamental limitation of recovering bitumen from low grade oil sand ores is its slow and ineffective aeration of the liberated small bitumen droplets. Gas nucleation and cavitation could provide better mechanisms for accelerating bitumen-bubble attachment. A research program was undertaken to examine factors affecting spontaneous bubble nucleation on bitumen surfaces. The results demonstrate that surface hydrophobicity and existence of gas nuclei in process water play a critical role for bubble nucleation. While there are more bubbles nucleated on highly hydrophobic silanated glass surfaces than on moderately hydrophobic bitumen, bubble nucleation on clean hydrophilic glass surfaces is negligible. Heating process water up to 85 ~ 95oC (as used in commercial operation) or boiling tap water prior to gas nucleation tests is shown to remove sufficient amount of gas nuclei existing in the water, thereby drastically reducing the number of bubbles nucleated on bitumen. Enhancing gas nuclei formation in hot process water is identified as a promising strategy to improve bitumen-bubble attachment during oil sands conditioning, and hence to increase bitumen recovery from low grade ores.

Jan 1, 2014

By L. Shasko

Deliberative mapping is a method of public engagement designed to bring citizens and specialists together to inform policy decisions in conflict-laden areas of science and technology (Stirling and Davies 2004a). Citizens and specialists participate in the process both separately and together. A deliberative mapping study was held in Regina, Saskatchewan in October and November of 2019. Participants in the study assessed options for reducing greenhouse gas emissions in small, remote or off-grid communities, including assessing the role of small modular nuclear reactors (SMRs) in climate change mitigation. Deliberative mapping is designed to facilitate direct, two-way conversations between citizens and specialists through both formal and informal discussions. The relationship building component of this process may increase trust. Public consultation processes that lack two-way dialogue or are seen as obligatory rather than meaningful can worsen public opposition or lead to negative public perceptions. Public education alone is not enough to change public opinion. Providing people with more information on topics they already hold opinions on can work to reaffirm previously held biases, but building relationships can provide new pathways to overcome divisions and turn close-mindedness into open-mindedness.

Jan 1, 2020

William Kent, New York City: I regret that I have not had the time since the Cincinnati meeting to make as complete a study of Mr. Salom&apos;s paper as I wished. I regard it as one of the most important papers that have been presented on this subject, and worthy of complete study. I started out, on the limited time I had, on a system of study which I would recommend to any one else who has leisure to complete the investigation. I took the original report presented at the Cincinnati meeting, and selected from it&apos; such tests as had the analyses reported along with the physical tests, giving the amounts of carbon, phosphorus, manganese, etc., taking only those in which all these elements are given.

Jan 1, 1885

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By Evgueni Jak

Recent advances in analytical, experimental techniques, and computer-based theoretical modelling of fundamental properties and elemental processes, provide new opportunities to develop the next level of whole-of-reactor pyrometallurgical furnace models. These models have the potential to significantly improve the prediction of, and adding value to, industrial operations. In non-ferrous smelting, the starting point of these models is the development of multicomponent thermodynamic databases for gas-slag-matte-speiss-metal-solids phases supported by systematic experimental research. The whole-of-reactor-models additionally should take into account kinetic processes taking place at micro- and macro- scales, and other key factors. Examples of applications of the latest research tools and modelling approaches to analysis of industrial flash and top submerged lance (TSL) sulphide smelting processes are presented. Different levels of industrial modelling are discussed from elemental local reactions, through general and more detailed whole-of-reactor-models, to plant sections and further to whole plant operation models. Some principles for development of pyrometallurgical reactor models are discussed.

By P. M. Hawley

In April 1975 Kaiser Steel Corporation and the United States&apos; Department of Energy entered into a cost-sharing agreement for the demonstration of shield-type longwall supports on three consecutive longwall panels at Kaiser&apos;s York Canyon&apos; Mine in New Mexico. Under this agreement the Department of Energy supplied 117 Hemscheidt 320 HSL caliper-type shield supports and hydraulic pumps for the duration of the demonstration. The purpose of the demonstration was to educate the U.S. coal mining industry as to the benefits in production, productivity, health and safety, and increased coal extraction afforded by shield-type longwall mining systems and to provide the industry with a working model. A detailed description of this demonstration is given in U.S. Department of Energy Publication No. DOE/ET/12530-T1, entitled "Demonstration of Shield-Type Longwall Supports at York Canyon Mine of Kaiser Steel Corporation," hereafter referred to as the York Canyon Report.

Jan 1, 1984

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of nee&apos; water and reused 3.8 billion gallons for a total usage of 12.4 billion gal¬lons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain this high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ore near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand for new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements ill the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By Lawrence Tsang, Conrad Ng, Tim Leung, Peter Poon

"The Mined Tunnel is part of the Central-Wan Chai Bypass and Island Eastern Corridor Link (CWB), which is a strategic road along the northshore of Hong Kong Island targeted to alleviate the heavy traffic congestion. The objective of this paper is to review the performance of construction of a 160m long Mined Tunnel with a trinocular cross-section area of 460m3 and a combined span of about 50m underneath the southern approach ramp of the existing Cross Harbour Tunnel (CHT) by sequential excavation method (SEM) in hard rock. Mechanical excavation of tunnel by adopting the New Austrian Tunnelling Method (NATM), together with the application of NGI Q-system allows observational approach and optimization of temporary rock support design. Furthermore, the good performance of optimized rock support and the stability of CHT are confirmed through instrumentation monitoring review. This paper also discusses the selection of different tunnel plant and equipment to achieve the planned rates of tunnelling by mechanical excavation in competent granitic rock. INTRODUCTION The works of the CWB mainly comprise construction of 4.5km dual three-lane trunk road, of which a 3.7km section is a tunnel connecting Rumsey Street Flyover in Central to Island Eastern Corridor at North Point (see Figure 1). The Mined Tunnel runs from the ex-Public Cargo Working Area (ex-PCWA), underneath the existing CHT, and through the Causeway Bay Typhoon Shelter. The Mined Tunnel passes at an oblique angle beneath the southern portal of CHT over a length of some 50m. CHT is the primary sensitive receiver of this project and is utilized with a daily throughput of about 120,000 vehicles that far exceeds the design capacity of 78,000 vehicles per day. Hence it is necessary to choose the most appropriate tunnelling method to preserve the structural integrity of the CHT. Other sensitive receivers in the vicinity include structures to the north of the Mined Tunnel, the Royal Hong Kong Yacht Club (RHKYC); and to the south of the Mined Tunnel, the Police Officers’ Club (POC)."

Jan 1, 2016

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019

By E. W. Sawyer

Attapulgite is a magnesium aluminosilicate clay mineral which exhibits unique, processing-enhanceable physical and chemical properties that are related to its current commercial uses. Properties of commercial interest are gelling, absorption, adsorption, binding, acid neutralization and many others. Major industrial applications are: (1) absorption by heat treated grades utilized in industrial oil and grease absorbents and in agricultural pesticide carriers; (2) gelling of aqueous liquid products by colloidal grades for stabilization and viscosity control in salt water drilling fluids, suspension fertilizers, liquid animal feed supplements, paints and tape joint compounds; (3) adsorption by heat treated varieties for the removal of catalysts, color bodies and other polar compounds from hydrocarbon streams; (4) gelling of organic liquids by colloidal attapulgite/surfactant blends in oil-type paints, fibrated and nonfibrated asphaltic coatings and mastic compositions, and (5) the binding of feeds and molecular sieve sorpents with colloidal type attapulgite products. These applications and other less common uses and potential uses will be discussed along with, the necessary selective mining and plant processing features related to each property and application.

Jan 1, 1986