Search Documents

By Charles A. Mitke

Discussion of the paper by CHARLES A. MITKE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1941 to 1958. GERALD SHERMAN, Bisbee, Ariz.-Mr. Mitke justly might have made much stronger his claim for increase in efficiency of labor due to the introduction of forced ventilation. The product per man shift in stoping in the Gardner division has practically doubled. While it is true that improved methods have been responsible for a great part of this gain, and what is due to better ventilation cannot be definitely known, yet it is also true that the results could not have been obtained in that division as it was in 1912. . The paper discusses the two systems of ventilation in use, exhaust and pressure. In both the object is the same, to take foul air or gas out of the mine by the most direct course and replace it by fresh. In coal mines, the exhaust system is in almost universal use, and since the most advanced work in ventilation has been in that class of mines, it was naturally the first one to be considered. It has the advantage of leaving all adits, shafts, or other openings free for use. Doors are only needed to direct the course of the air, and not to confine it. Its disadvantages appear in case of fire, or if the ground over the mine is much broken by subsidence. The fan must work in gas in the case of a -fire, and may be. damaged or destroyed either by heat or by corrosive gas. At the time of the fire in the Lowell division of the Copper Queen, a small exhaust fan was placed over a ventilating raise, but the vanes and housing were destroyed by sulphurous gases within a few weeks. If the ground above the mined area is much broken, as is frequently the case when the ore deposit is thick vertically, a good deal of air is likely to pass through it, particularly if it is near the surface. Leakage from this source is a loss to the exhaust system by short circuiting, which is exaggerated by a contraction or block in the air course. It serves as an added outlet in the pressure system. This is strikingly shown at the United Verde, where many jets of steam may be seen coming up through the ground above the stoped country on a cold day.

Jan 12, 1915

By Tianzu Yang, Weifeng Liu, Shu Bin, Lin Chen, Wanda Bin

"Vanyukov Process has been mainly applied for processing copper and nickel sulfide ore for more than 30 years. Based on the understanding of the Vanyukov Process, researchers from China introduced the technology into the areas of lead, antimony and bismuth extraction by changing the furnace structure and technical flow, which greatly extended the application area and raised the processing efficiency, thus developed the oxygen-rich side-blow bath smelting (OSBS) technology in 2000. This contribution reviews the history of OSBS technology from four respects: the quantity, the furnace structure, the process flow and the application area. Its potential research direction and industrial application are also summarized.IntroductionVanyukov bath smelting furnace and related bath smelting technology were developed by researchers from Soviet Union who devoted comprehensive research on fundamental theory as well as engineering technology [1,5]. Vanyukov process has been applied for large industrial production since the 1970s and it is still one of the major methods in modem pyrometallurgy process. The appearance ofVanyukov double district furnace and joint double furnace in the past ten years, which are applied for copper smelting, is the most valuable advances of the Vanyukov process [7,8,9]. However, the application ofVanyukov process was limited in copper and nickel sulfide ore smelting, and few countries adopted this process except Soviet Union."

Jan 1, 2013

By H. P. Greenwald

[For sarno years past the Safety in Minbr. Resaarch J30ard of Great Bri tr-dn ha:1 been making ar.. intensive Gearch for, traterials that \.'ould be 1!\ore ef-ficient than rock dust and th t 'could l1eplace it Jholly or in El:}rt as a muans of prevEll'ltine the propa 'tion' of 'c63.1~dust exnlosions in. mines21 In the course of this \o.'ork several rock c.ur--ts md numerous inorganic compounds I,/ere tested. The result w place incombus.ti ble substFlnces in two main groups~ (1) r.:ho se who sa effect' in suppre aeina Jlihe cor.lbustion of coal dUDt i 0 pro-]

Jan 1, 1940

By F. E. Armstrong

A program with the objective of developing a fast, accurate instrumental method of analyzing mine dust for incombustible content has been underway in the Bureau of Mines for several years. Several prototype instruments making use of a gamma-ray backscatter technique have resulted. Although extensive laboratory testing has shown that these instruments are accurate under laboratory conditions, only extensive field testing will prove their ultimate practicality and usefulness. This report shows that under most conditions these devices are at least as accurate as the volumetric method and much faster in use. Other data obtained during the same study concerning mine dust are presented; these concern moisture content, sample bulk density distribution, and some particle size distribution information.

Jan 1, 1973

By V. R. Bovino

You have afforded me the challenge of saying something profound in 20 minutes that will stay with you for 20 years. My hope is that from this presentation you will extract ideas that will move you? out of your offices, into the mine to seize upon the concepts that we will discuss. Your challenge is to transform those concepts into action and give life to the ideas discussed here. The notion of achieving limitless productivity produces peak levels of enthusiasm in today's mining leaders. Highly-productive mines do not happen by chance --they are created by progressive leaders. The quest for productivity improvement, exclusively through capital investment and technological advances, is an incomplete process. Improvement, through capital and technology, is often not achieved because we fail to energize the true potential and commitment in our employees.

Jan 1, 1991

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By Tianming Sun, Gabriella Tranell, Ragnhild E. Aune, Mark William Kennedy

Rare Earth Elements (REEs) are critical for the production of many advanced materials and products. Mining and primary production of REEs are generally associated with significant environmental impacts. By recovery of REEs from secondary sources, through recycling or as a byproduct, the adverse environmental impacts may be partly avoided. In the present study apatite concentrate originating from iron ore beneficiation done by LKAB in Kiruna, Sweden, is explored as a possible source for REEs. The composition and distribution of the REEs within the concentrates are studied using ICP-MS, XRD and SEM-EDS/EPMA, as well as the melting point and heat of fusion using DTA-TGA-MS. The behavior of the material during melting has also been studied through wetting and slag saturation experiments. The overall aim of the study is to evaluate the implications for future smelting experiments aimed at concentration and recovery of the REEs.

Jan 1, 2015

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses' and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By N. Ahern, L. Manoukian

"Cyanide is a leaching agent for precious metals commonly used in gold ore processing. Cyanide exists in various forms (including free, complexed as weak or strong complexes, and as ions such as cyanate and thiocyanate), so its detection, speciation and analysis in processing or environmental samples can be complex. This paper will review best practices for cyanide sampling and preservation in the field, interferences and pretreatment methods required prior to sample analysis and analytical methods that are used for cyanide species. Titrimetric, flow injection ligand exchange, spectrophotometric, colorimetric, potentiometric, amperometric, and chromatography techniques will be discussed and their chemistries, detection limits, advantages and limitations will be described.INTRODUCTION Cyanide is well known to be an extremely toxic species. Accurate cyanide measurement in effluent from mines is critical from an environmental perspective. Its measurement is also an important control parameter in the recovery of gold using cyanidation. Cyanide chemistry is diverse and complex, and cyanide analysis can be challenging as a result of and because of limitations in understanding of analytical methods. Various chemical mechanisms can form or destroy cyanide, and the sample matrix or preservation chemicals can also affect analytical results. These interferences make the collection of reliable cyanide measurements challenging and can start as soon as the sample is collected, during laboratory pre-treatment and during analysis. This paper reviews different methods of cyanide measurement. The basic chemistry of cyanide, best practices for sampling and preservation, as well as various methods of analysis will be discussed.CHEMISTRY The complexity of cyanide chemistry is well known (Beck, 1987; Delgado, Botz, Bucknam, Milasovljevic, & Staley, 2008; Botz, Milosavljevic, & Ward, 2013) and is attributed to the ability of cyanide to undergo: •,Volatilization •,Precipitation •,Adsorption •,Complexation with metals •,Oxidation to cyanate, ammonia, or cyanogen chloride •,Reaction with sulfur or sulfide minerals to form thiocyanate •,Redox reactions leading to the formation of cyanogen and cyanate •,Redox reactions (of some cyano complexes) •,Photochemical reactions (of some cyano complexes)"

Jan 1, 2017

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By José Luiz Rodrigues Bravo

The production of electrolytic copper with assured quality corresponding to international standards, in a conventional electrorefkery of a custom smelter, is a hard and cautious task, if no advanced technologies for selective control of electrolyte impurities are available. The improper control of the amount of As , Sb and Bi in the anode that enter the tankhouse , attributable either to a bad schedule of concentrate input or to the unavailability of clean concentrates in the international market , as well as the lack of means to maintain the suitable level of these elements in the electrolyte together with other operational circumstances, can result in off-grade copper, as well as affect the starting sheet chemically and physically. This paper presents in a practical way the relationship between the operational conditions and the cathode and starting sheet quality produced at CMSA, covering the period of the last five years of operation, discusses the technologies available in the market for antimony and bismuth removal and compare the results of testwork, achieved in the laboratories of CMSA, using two resins not associated with patented technologies.

Jan 1, 1997

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By William M. (Bill) Shaver

"The author will review the early history of shaft sinking as well as focus on the improvements made in shaft design and construction over the last fifty years (1970 to 2019) to predict how shaft sinking will change over the next fifty years and describe what the shaft sinking world might look like in 2070. INTRODUCTION It is a great honour to be one of your keynote speakers for the Fourth International Conference on Shaft Design and Construction being held in Toronto in November 2019. This is one of the opportunities we have to thank the Mining Companies of the world as well as the industries and companies we serve for their support of the mining contracting and shaft sinking business of Canada and the world at large. Many of these companies are represented here today. Without your support many of the innovations we will talk about today would not be possible. We would also like to thank all the companies that work with us in our business including all the contractors and suppliers who provide the various services we require. These include equipment manufacturers, engineering companies, project management companies and suppliers large and small who cater to our every need as quickly as possible. Without all these partners we would not be as good as we are. Many of these companies are our sponsors this week. Thank you from all of us! This is also an appropriate time to pause and think about those Shaft Sinkers we have lost and those who have been injured on our projects around the world. Please bow your head and remember the Shaft Sinkers you have worked with, who did not return home or those who returned home injured. Think about how we can continue the work of making shafts safer every day as we go forward with our projects so everyone goes home to their families safe and sound. Pause for a minute and thank you. The subject matter we have chosen to discuss today is “Shaft Sinking in the Next Five Decades”. How will the work be done, how fast will it be done, what will it cost, and why we think this may occur? It is appropriate to consider this over the next few days with this auspicious group we have assembled. Today, we will look back at all the advances that have been made over the last many years and look ahead to the future to attempt to predict what shaft sinking will look like in 2070. When I look around the room I recognize that many of us will not be around then so we need not worry about being wrong. Suffice it to say that the next 50 years will be very interesting and exciting for the shaft sinking business."

Jan 1, 2019

By E. H. Burroughs, M. J. Gavin

The references in the following compilation are selected chiefly from the literature of the years 1915-1920 , though a few of the more valuable standard works published before that period have necessarily been included . References to many articles have been omitted purposely , because the material covered by them is duplicated in publications included in the bibliography . It is manifestly impossible for the Bureau of Mines either to recommend or adversely criticize the statements of the various writers , particularly as to cost and profit estimates in articles referring to American shales , but it is hoped that the investigator will use caution in considering such statements , as it is well known that much of the literature on this subject has been published for promotion purposes and is therefore over- enthusiastic . Bearing this fact in mind , the reader should be able to judge for himself the reliability or usefulness of these articles .

Sep 1, 1921

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

By D Kentwell

IGO Ltd’s (IGO) Nova Operation (Nova) is 160 km east-north-east of the town of Norseman in Western Australia (WA). Discovered by Sirius Resources NL (Sirius) in 2012 and acquired by IGO in 2015, the Nova-Bollinger Deposit (Nova-Bollinger) occurs within the Fraser Zone of the AlbanyFraser Orogen. Nova-Bollinger is a complex nickel-copper-cobalt (Ni-Cu-Co) magmatic intrusive sulfide deposit, which is characterised by high-grade folded and undulating breccia lodes that host the bulk of the payable metals. Significant sulfide mineralisation is also found in several magmatic intrusive styles including net-textured, disseminated and blebby styles. A smaller but material volume of sulfides has also been remobilised into the deposit’s footwall rocks as ‘stringer’ bands in metasediments, or as discrete massive sulfide lenses. When interpolating Mineral Resource estimate (MRE) block grades in the presence of locally varying grade connectivity trends, such as folds or undulations, the sample search neighbourhood, which is used to identify the composites subset that is used for each block estimate, should be oriented to match the local trends. In theory, the most robust method of estimation where locally varying angles (LVAs) are applied to search neighbourhoods, are techniques where the composites and the blocks to be estimated are transformed to an unfolded coordinate system (UCS). However, UCS methods can be tedious to implement and require subjective decisions to be made that cannot always be fully defended. An alternative LVA method commonly used in the industry is dynamic anisotropy (DA), which is much simpler to implement and is often assumed (but not that often demonstrated) to result in similar results to UCS-style estimation. In 2018, Nova’s Mine Geology team (MGT) estimated the grades and density of the Nova-Bollinger MRE using the UCS approach. For the 2020 MRE update, Nova’s MGT tested and compared the USC grade interpolation method with the DA approach. As applied to the Nova-Bollinger’s 2020 MRE, the comparison, advantages and disadvantages of the two estimation methods are the subject of this paper

Mar 22, 2022

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-cu-yd) transit mixer and a shotcrete spray boon carrier, is used by a two-man crew to transport and place up to 25 m3 (32 cu-yd) of steel fiber reinforced, dry, silica fume shotcrete per 11-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control are performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1992

By D Chalmers

After the sustained use of the GAG (Górniczy Agregat Gaśniczy) engine at a Queensland coalmine, it has raised questions as to its effectiveness as a remote firefighting tool. All firefighting apparatus have advantages and limitations, however the deployment of any apparatus must be based on its likelihood to succeed and effectively extinguish the fire or bring it under control. A recent study conducted for ACARP by researchers at UNSW has highlighted that there is more to be learned about the GAG. As coalmines are mining at greater depths and fan pressures are much greater than they were when the GAG was introduced, deploying the GAG may be a total waste ofresources and may place operators at greater risk. When the GAG unit is positioned on the surface of the mine, the pressure it generates has to overcome buoyancy of the exhaust gases and the frictional resistance of the borehole and part of the mine circuit. Buoyancy in deeper holes can lead to the GAG pressure relief system opening, venting out the products to the atmosphere without delivering any product to the mine workings. Additionally, frictional resistance is a function of distance. Deeper holes will have a greater frictional resistance than shallow holes. Delivering sufficient products from the unit will be limited by the available pressure that has to overcome the buoyancy, and increased mine resistance thatconsumes any residual pressure. By documenting the limitations of this unit it will enable better decisions to combat a fire or spontaneous combustion event.

Oct 12, 2022