Search Documents

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By D. D. Rodier

Most zinc concentrates contain some silver and varying amounts of such valuable trace elements as gold, indium, germanium and gallium. With increasing similarities in plant installations, the predominance of electrolyte process and the increasing environmental constraints on iron disposal, it is essential that zinc smelters optimize the recovery of any valuable elements in their feed stocks. The process options, to date, of smelting, flotation or leaching of silver-rich leach residues cannot be applied economically to all installations. It is therefore necessary that new innovative processes, to recover silver and other valuable metals from relatively low grade feeds, be developed. This paper attempts to place this strategy in the context of today's constraints and will also provide a simple evaluation tool for any process alternatives.

Jan 1, 1990

By Philip D. Wilson

FEAST and famine-or, chronologically, famine and feast-have characterized the aluminum supply program during 1943. Fortunately for the war effort the famine phase is over and aluminum production is now in the happy position of being abundantly able to supply all the requirements of the armed services plus a monthly surplus which is building up a substantial stock pile as a reserve against any contingencies. But the present condition of oversupply cannot be attributed to the super-efficiency of the aluminum production program which was designed to take care of the over-all requirements of the war with little or no margin of safety. The present more than comfortable situation is due primarily to the fact that the armed services generally have not consumed anything approaching the amount of aluminum which their requirement estimates indicated.

Jan 1, 1944

By M. Mpofu, G. Stenzel, F. Magweregwede, B. Maphalala, T. Kgarume

Surface coal operations in which mining activities are conducted above old underground workings experience hot holes after drilling. In a coal mine, hot holes are defined as shot holes, which after being drilled have an in-hole ambient temperature of 40°C or above or show a temperature increase of 3°C or more during monitoring. Hot holes and other cavities, such as cracks, pose health and safety risks to workers, such as exposure to hot air and high concentrations of noxious gases released from these holes. In addition, workers may be exposed to premature detonation of explosives caused by in-hole temperature increases and chemical reactions. To this end, Coaltech Research Association commissioned a project to develop a Best Practice Guideline for the management of hot holes. This paper is a compilation of the activities conducted in the development of the Best Practice Guideline between 2021 and 2022. The activities included a review of standard operating procedures and hot-hole temperature-measuring and -monitoring devices, and the assessment of current hot-hole procedures at selected mines. The results indicated that management of hot holes requires a focus on pre-emptive risk assessment of mining blocks, identification of hot holes using the correct temperature-measuring devices, and continuous monitoring of hot holes from the time of drilling until just before blasting. Hot-hole management accessories, such as polyvinyl chloride sleeves, were found to be effective in insulating the hot-hole emulsion from the rock mass temperature, thus preventing the potential for premature detonation.

Sep 9, 2024

By K Grohs, A Satriawan, S R. Pearce

Martabe gold and silver mine is operated by PT Agincourt Resources (PTAR) and is situated in northern Sumatra and comprises several deposits in steep terrain, and in a tropical climate, that are required to be developed in the optimal sequence for the best possible Net Present Value (NPV) return on the project. In addition, the waste rock from excavations and tailings from processing is a by-product to be scheduled and used for a number of purposes identified as part of life-of-mine planning. These uses include construction of the current integrated tailings storage facility (TSF) as well as future engineering construction and waste disposal projects which includes plans for a program of in-pit backfilling. These plans need to be aligned to ensure the waste rock and tailings can be contained relative to the production rate. Given that the site will have multiple open pit voids upon cessation of mining activities opportunities for integration of in-pit disposal of mine waste have now been assessed with technical studies to review the practicality of the approach with respect to operational challenges and conformance with closure planning requirements. This includes assessment of disposal of waste rock, tailings (including consideration of filtered tailings) and co-disposal of waste rock and filtered tailings.

Aug 2, 2023

By N. Skopak, W. Birch, A. Douglas, C. Johnson

Determining the origins of air overpressure has been a long-debated topic within the explosives engineering community. Historically, it has been accepted that the initial face movement gave rise to air displacement, resulting in an air overpressure pulse. Later research proposed that the air overpressure pulse resulted from the shockwave rapidly propagating through and impacting the quarry face. Most recently, researchers have derived that air overpressure is associated with the gas phase from which a gaseous product from explosives rapidly pours out the quarry face under high pressure. Significant research has strongly indicated that the time at which the air overpressure pulse exits the face fails to coincide with either the arrival of the shockwave at the free face or the initial face movement. Research has consistently shown that the shockwave arrival at the face occurs before the air overpressure pulse leaves the face. Therefore, to best determine which blast mechanism contributed to the initial air overpressure pulse, testing was aimed at verifying the precise time at which the air overpressure exited the faces compared to when the face first moved. This research describes tests using scaled concrete blocks, which provided the ability to control the key parameters necessary for the research to be successfully concluded. Black powder was selected as the energetic material to eliminate the production of the detonation wave while still inducing other gas-producing effects. The components evaluated were air blast arrival times in front of the face, the initial movement of the blast face, the precise initiation time of the blast hole, timing of pressurization within the rock mass (between borehole and face, or adjacent borehole), and the speed of sound in the air. A detailed timeline was created which portrays the actions within the blast to promote an understanding of the sequencing of events. The results showed that the initial face movement occurred at 17.57 milliseconds (ms) while the calculated time at which the air overpressure exited the face occurred at 7.07 ms. The large disparity continues to reaffirm the premise that the origin fails to coincide with the air pressure pulse. Average pressurization through the block occurred at a rate of 341.23 feet per second (104.15 meters per second) which resulted in the gas release pulse being calculated to exit the face between 4.41 and 6.21 ms. This pulse correlates more accurately with the air overpressure origin timing which will be the focus of continued research. Knowing the precise origin of blast-induced air overpressure will assist in being able to better control it through appropriate blast design.

Jan 1, 2024

By Moylan T, Stewart D

A case study examining the procedures and financial benefits of introducing dump leaching to augment the Mt Gibson Gold Project CIP operations is discussed. Metallurgical testwork, followed by pilot dump leach operations, confirmed that gold recoveries of greater than 60 per cent could be achieved by dump leaching Mt Gibson laterite ore. Capital and operating costs were determined. Pit optimisation using the Whittle FOUR-D optimisation program calculated an optimum cutover grade between CIP and dump leaching for one orebody. The resultant recalculation of reserves based on CIP and dump leach operating costs showed that reserves for that orebody could be increased from 329 000 tonnes at 1.9 g/t An, to 1 488 000 tonnes at 1.2 gh An. NPV for the CIP only option of $1.4 m, was increased to $4.0 m for the combined CIP/dump leach option. This technique can be applied to existing gold projects and to new Developments.

Jan 1, 1992

By Margaret R. Lickes

Mercury was produced originally at the Idaho Almaden mine from 1939 to 1942. When the ;.nine was shut down, more than 100,000 tons of ore, containing from 2.5 to 3 pounds of mercury per ton, was known to be adjacent to old workings but had been considered too low grade for commercial operation. Later, detailed, systematic exploration by Rare Metals Corporation of America increased and delimited enough minable reserves for further operation to be foreseen for several years. The average grade of the ore is estimated at slightly more than 3.5 pounds of mercury per ton. Open-pit mining and installation of the largest rotary kiln in the United States furnacing mercury ore have made possible profitable exploitation of these reserves (fig. 1). The bulk of the exploration was by percussion drilling, although some diamond drilling was done to check the results. When enough reserves were indicated to assure a successful operation, stripping and plant construction were started simultaneously. Figure 2 is a general view of the plant. The ore bodies, although irregular in size, shape, and grade and covered by essentially barren cap rock, are amenable to low-cost, trackless, open-pit mining. Development consists of stripping the overburden and removing, barren cap rock. Ore is being mined at approximately [5],000 tons per month and treated in a 175-ton-per-day furnacing plant.

Jan 1, 1957

By Z. S. Abisheva

Results of the study targeted to development of universal acidic-extraction-precipitation technology for gallium recovery from the sublimates are presented in the paper. This will let to utilize a new non-traditional source for gallium production. Phase composition of gallium containing dust was studied. Forms of gallium in the sublimates were determined. The main form is Ga2O3, however, GaP form is also present in the cottrel dust and Na5Ga3F14 form is present in the dust of aluminum electrolysis. The possibility of gallium concentration was established via secondary pyro-selection of the dust. Kinetics of interaction of dust components with sulfuric acid was studied. The products of the interaction subsequently were leached with water. Optimum conditions for direct leaching with HCl and H2SO4 were determined providing gallium recovery from the cottrel dust and the ash carry outs up to 95 %. Gallium recovery from the primary dust and the secondary dust of aluminum electrolysis was at 52; 64 % and 63; 83 % respectively. Effect of Fe, P, K, Na and Al admixtures for gallium extraction from hydrochloric acid solutions was studied. It was shown that gallium chloride complex (GaCl4-) is extracted into the organic phase from the following acid mixtures: HCl + H2SO4, HCl + H3PO4, HCl + H2SO4 + H3PO4, HCl + HF. Kinetic regularities of gallium extraction in the system (tri butyl phosphate) TBP ? HCl - Ga were studied using diffusion cell method with agitation. Optimum conditions for gallium extraction from complex hydrochloric acid solutions with TBP were found providing 99.9 % recovery and separation coefficient for gallium and iron (III) of more than 25 in one stage. Sodium hydroxide and water were selected as reagents for re-extraction of gallium from the organic phase. Different options for disposal of by-products that are formed in the processing of cottrel dust, ash sublimates and dust of aluminum electrolysis were proposed and tested. Keywords: gallium, kinetic, sulfatization, leaching, extraction, technology

Sep 1, 2012

By Hugh S. Spence

This paper deals with an occurrence of radium ore near Wilberforce, Haliburton county, Ontario, upon which development work has recently been undertaken and which seems more likely to prove of commercial grade than any other deposit' of radioactive minerals hitherto found in Canada. This occurrence is sometimes called the Richardson property, after Mr. W. M. Richardson, the discoverer, and will be so referred to in the present paper. Occurrences of radioactive minerals are not uncommon in eastern Canada, and a number are recorded in the literature. The earliest of such references is probably that in Geology of Canada, 1863, where is mentioned an occurrence of uraninite at Mamainse, on the east shore of lake Superior. The mineral was first described by J. L. Leconte, in 1847, under the name of coracite, and was said to occur in a two-inch vein at the contact of trap and syenite. Search for this locality in recent years has proved unsuccessful. Obalski, in 1894, mentions (1) the occurrence of uraninite at a mica mine near Murray Bay, Que. In 1903, Obalski records (2) tests made on this uraninite by Rutherford and the Curies and the determination in it of the then newly-discovered element radium. In 1901, he mentions (3) the occurrence of uraninite at the Villeneuve mica mine, on the Lievre river, and of samarskite at the Maisonneuve mica mine, in Berthier county.

Jan 1, 1930

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By P. D. Kovscek

The performance of a novel prototype kerf-cutting impact mining machine was evaluated under a cooperative agreement between the U.S. Bureau of Mines and RAMEX Systems, Bellevue, WA, while operating under conditions typical of normal tunnel entry development. Selected operating parameters were monitored concurrently to determine baseline operating conditions and to study relationships between operating parameters. Using the data obtained, the specific energy requirements of the impact mining machine were calculated and compared to specific energy requirements of tunnel boring machines cutting in rock having similar hardness. Tests results indicate that the kerf-cutting impact mining machine can provide a mechanical means for mining very hard rock that cannot be effectively mined using commercially available mechanical excavators.

Jan 1, 2010

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By A Teen

An open cast mine on the West Coast of the South Island of New Zealand proposes to remove up to 30 m of overburden to access an ore body neighbouring National Reserve land. Part of the conditions of the mining permit is that no material above natural discharge levels may be released over the Mining Lease boundary onto the adjacent land. In order to meet this requirement, the client has contracted the design and installation of over 2.6 km of high energy dynamic rockfall control barriers. This paper describes how the rockfall hazards were assessed and the rockfall barriers dimensioned. The design involved 2D modelling of over 3000 simulations.   Modelling parameters were calibrated during field trials at a purpose built section of barrier. The resultant energies ranged from 500 to 3000 kJ. The construction phase of the project involved the drilling, anchoring, and installation of certified barriers up to 7 m high in a remote and inhospitable climate with limited machinery access. By exploring best practice in this specialized field of engineering, a novel rockfall hazard mitigation solution was identified.

Jan 1, 2007

By Frank Schrama

Steelmakers worldwide agree that the most efficient and cost-effective solution in BOF steelmaking is to desulfurize the hot metal between the blast furnace and converter. Various methods are currently in use, among which the Kanbara Reactor (KR, using only lime as a reagent), Magnesium mono-injection (MMI, using only magnesium; also known as the Ukraina-Desmag process) and co-injection (using magnesium and lime/CaC2) are leading. These three hot metal desulfurization methods are compared based on metallurgy, efficiency, costs and overall performance. Both available data from literature and experience from Danieli Corus engineers is used for this study. The KR process is able to reach low sulfur concentrations (> 10 ppm) in hot metal and has lower reagent costs. However, due to higher Fe-loss and heavy wear the KR process has the highest operational costs. The Magnesium mono-injection process is very fast due to the use of the reactive magnesium as reagent. Major problems with resulfurization (sulfur levels below 50 ppm cannot be reached) and the violence of the process made that this process could never get a firm foothold in the western steel industry. The co-injection process with magnesium and lime proves to be able to combine the best of both worlds. It can reach low sulfur concentrations and desulfurize fast. Co-injection is also the most flexible and cost effective.

Aug 16, 2017

By Alan M. Bateman

POSSIBLE postwar trends of the more important world minerals will be determined in part by their present world position and by the acts and forces that have operated during the war period, so it is desirable first to review briefly what has been happening in the foreign field of metals and minerals. When we first entered this war we of the mineral profession were all acutely conscious of our lack of strategic minerals and other materials, which had to be imported in great quantities-minerals such as manganese, chrome, tin, mercury, nickel, and antimony. But we realized also that we had to acquire vast quantities of those minerals of which we had thought we were bountifully supplied. Our assumed domestic abundances turned out to be woefully deficient, and demands also arose for new minerals never before produced in large quantities. Some threescore minerals entered the strategic list of our imports. Ores from new sources had to be sought, developed, and transported. Tonnages in the millions of such bulk materials as zinc, lead, copper, chrome, and manganese flowed to feed our war efforts. Sparsely distributed minerals such as tin, mercury, antimony, tungsten, cobalt, mica, and corundum had to be lured from their rock lairs in greatly increased quantities to feed the hungry maw of war industry, and the rare minerals such as tantalite, columbite, beryl, and quartz crystals had to be developed and procured in quantities never before dreamed of. New uses such as radio and radar created demands for many minerals formerly thought of only as adornments of museum collections and not as pressing industrial minerals. Such minerals were never before mined in quantity.

Jan 1, 1945

By Robert A. Jankowski

"Following passage of the Coal Mine Health and Safety Act of 1969 (Public Law 911173), the Bureau of Mines initiated a research program aimed at controlling respirable dust exposures of coal mine workers. Respirable dust is the dust that gets into, and interacts with, the lungs of those who inhale it. It has long been recognized as a severe health hazard to mine workers. This program has been implemented by a team effort consisting of the Bureau's in-house capabilities, the Generic Center for Respirable Dust, and contractors, as necessary. Over the years, Bureau research has addressed principally three areas:o Compliance with the Federal 2.0 mg/m3 dust standard (1970-76).o Dust control for longwall mining (1976-1983).o More stringent respirable dust standards due to quartz dust (1983-1987).In addition, fundamental studies have been conducted by the Generic Center for Respirable Dust, with emphasis on penetration of dust into the lung. Accomplishments have been significant, but problems remain, as noted later.The Coal Mine Health and Safety Act of 1969, established a 2.0 mg/m3 dust standard for all coal mining operations, underground as well as surface. At the time of enactment of this legislation, the industry was averaging approximately 4.0 mg/m3. The Bureau of Mines respirable dust research program played a significant role in identifying and developing effective technology to allow better compliance with this new standard, thanks to industry implementation and Federal enforcement."

Nov 1, 1988

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By A. Khoshnevisan

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals? concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2 g/L Mo, 1.5 g/L Fe, 0.5 g/L Cu and 60 ppm Re. A good extraction efficiency, up to 94%, was achieved for Re from the leached liquor, where the extraction of other metals, such as Fe and Cu, was negligible. In particular, at very low pH, rhenium is extracted selectively from solution, while the extraction of molybdenum is less than 10%. After removing rhenium, molybdenum was extracted with LIX984N. The selectivity of molybdenum extraction over other metals in solution was significant. Nearly 94% of molybdenum can be extracted from the solution at a pH value of -0.12, without any interference from other metal ions such as copper and iron.