Search Documents

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By James C. Barker

In 1981 and 1985-1986, the Bureau of Mines conducted orientation studies of marine placer platinum-group metals (PGM). PGM are derived from the Goodnews Bay ultramafic complex and magnetic surveys show that the complex extends offshore at least four mi. The present seafloor was an emergent foreland as recently as 8000 years ago. High-energy ocean processes are transporting and depositing sediment such that PGM-bearing materials are reworked and later masked by barren littoral drift. Exploration targets include 1) placers formed since present transgression began, and 2) ancient marine and drowned fluvial deposits. Additionally, there is evidence of PGM solution transport and accretion. At least minor values of PGM in Recent lag-type placers and possible submarine strands are concentrated along an offshore scarp incised through glacial deposits into the preglacial surface between Flat Cape and Red Mountain. Other Recent PGM-bearing features include Flat Cape shoal, Chagvan Bay, Salmon River delta, and modern beaches. Ancient placers include possible N-S fluvial systems 2 to 3 mi offshore, a nearshore scarp 50 ft below sea level, and strands adjacent to projected ultramafic bedrock slopes. The existance of ancient placers is dependent on depth of glacial erosion. SEM studies show PGM are principally isoferroplatinum and osmiridium, with minor sperrylite, moncheite, and platiniridium. Gold is a co-product, and concentrates comprise chromite, ilmenite, and magnetite. Beneficiation tests successfully concentrated precious metals from natural blacksand accumulations, but failed to concentrate low-grade lag gravels.

Jan 1, 2011

By Yongsheng Song, Yong Chen, Wenjuan Li

"Detailed characterization and improved recovery of a micro-fine, low-grade refractory gold ore from a beneficiation plant in Yunnan Province, China, was investigated. Different analytical techniques, such as videlicet size analysis, scanning electron microscopy, and mineral analysis by a Mineral Liberation Analyser, were used for mineralogical characterization of the ore. This paper describes an experimental study on the effect of the grinding fineness and the use of various flotation reagent regimes involving collectors, depressors, and activators on the flotation behaviour of micro-fine auriferous pyrite. Two-stage flotation resulted in high gold grade (32.71 g/t) and gold recovery (80.02%) of the bulk gold concentrate. This process opens the possibilities of maximizing Au recoveries in a micro-fine low-grade refractory gold ore where low recoveries are common.INTRODUCTIONWith the rapid development of the gold industry, refractory gold ores are becoming increasingly important resources for gold production (O’Connor & Dunne, 1994; Agorhom, Skinner, & Zanin, 2012). Among these refractory gold ores, sulfur and micro-grained native gold ores represent a significant challenge, since they are not amenable to gold recovery by direct cyanidation. The gold contained in this type of ore is very finely disseminated and encapsulated in sulfides, which makes it inaccessible to the cyanide solution during direct cyanidation (Bulatovic, 1997; Allan & Woodcock, 2001). Autoclave pressure oxidation (AC POX) of the sulfide ore and subsequent cyanidation is a common technology used to recover the gold in such types of ore. Flotation is often used as a pre-treatment method to refractory gold ore (Monte Lins, & Oliveira, 1997).As the gold-carrier minerals are usually finely disseminated (sometimes under 10 µm) and intimately associated with gangue minerals, a fine grind is necessary to get a high degree of liberation. At the same time, the fine grind usually causes the production of significant quantities of slimes, which comprise easy-to-float gangue minerals such as mica, dolomite, and calcite. These mineral phases are naturally hydrophobic and float readily, competing with the value minerals in the froth phase and resulting in lower concentrate grades."

Jan 1, 2016

By Alfred C. Lane

Reference to the original use of the terms Laurentian and Huronian (and its extension), shows that the former was applied to granitized sedimentary and metamorphic pre-Cambrian rocks, and the gneissoid igneous rocks associated therewith, and the latter to non-fossiliferous rocks supposed to be later. But it appears from the work of Collins, Quirke and others that there is more or less of an overlap, and that of the original Laurentian the Grenville limestone, and some of the granites, may be later than the lowest part of the original Huronian. Before we can decide whether to abandon one or the other of the two terms, or how to delimit them, it is important to know the extent of this overlap. The Pb :U ratio, though not to be depended upon too minutely, does give a real idea of the age of a mineral as it increases with the decay of uranium, and so is greater the longer the time since the uranium was separated: and there are reasonable prospects of help there from in getting a knowledge of the relative age of different granites to assist in solving the problem, as facts already collected show. 1. Historical review of the use of the words Laurentian and Huronian: 2. Difficulty encountered: 3. Popular account of atomic disintegration: 4. Methods of estimating age by it: 5. Applications.

Jan 1, 1925

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made an the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By S. K. Kawatra, T. C. Eisele

"Recent advances in microbiology have made the application of biotechnology to metallurgical processes possible. Hydrometallurgy stands to gain the cost from the use of microorganisms, as they are useful for both dissolution aids and for removing metals from solution. The development of genetic engineering techniques promises to greatly increase the importance of bioprocessing of metals and minerals by the year 2000.In this paper, the basic effects of microorganisms on metallurgical processes are reviewed, and the applications which are currently either in use or near being used are presented. Representative data collected at Michigan Technological University is also given.IntroductionMany hydrometallurgical operations exist which are thermodynamically possible, but which are industrially impractical due to slow kinetics, high reagent costs, or the need for a highly corrosive environment. However, recent discoveries in microbiology indicate that in many cases these difficulties can be reduced greatly by the action of bacteria and other microorganisms (1-8).A major advantage of using living organisms in hydrometallurgy is that once the culture is established the microorganisms produce their own reagents either from the material being processed or from low-cost nutrient supplements. They thus allow extremely complex chemical reactions to be carried out at reasonable cost. The major drawback of using microorganisms is their inability to tolerate extremely high temperatures, excessive concentrations of toxic metals, or very highly acidic, alkaline, or corrosive conditions. However, the complex reactions which bacteria make possible frequently eliminate the need for such extreme conditions. Also, in recent years a number of organisms have been isolated from such exotic environments as hot springs and deep-ocean vents which can tolerate temperatures higher than was previously thought possible for any organism, and can catalyze a number of metallurgically important reactions (8)."

Jan 1, 1988

By Raphael Victor

The construction and modification of tunnels brings a requirement for precise measurement of convergence and divergence to safeguard the structure, maintain safety and provide the assurance needed to maintain efficient progress. Established methods include manual measurement using tape extensometers and automated methods using photogrammetry and automated total stations. Drawbacks include the need for frequent access, power supply, cabling, and cost. The paper describes how the development of reliable optical displacement sensors (ODS) has changed the landscape. ODS sensors are connected to a long-range wireless mesh communications network via a solar-powered gateway outside the tunnel, with data instantly transmitted to the internet. A sensor and its reflector target can be installed in 20 minutes and is maintenance free for a decade. Tunnel movement is measured to sub-millimeter precision with repeatability of ±0.15 mm. Integration of a triaxial tilt sensor allows slope distance to be converted to horizontal and vertical changes and allows rotational movement to be determined. Applications include new-build and long-term structural health monitoring. Case studies will be given, including the refurbishment of rail tunnels in Spain where the ODS measured movement during track lowering in a situation where no other automated system was considered viable.

Jun 13, 2023

By Louis Cabot

A pilot plant of the Modular Gold Processing Unit (MGPU) was designed, installed and operated, over a 8 months period, by RSW-Béroma, at the Granada Mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up as well as exploitation results, including productivity and profitability curves, are given for a small scale mining operation in comparison with larger ones. Copyright ã 2001 CIM

May 1, 2001

By S. K. Sharma

The Bureau of Mines has investigated the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters such as shear rate, polymer dosage, and polymer concentration on floc growth and to determine the applicability of a model in predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. Results show that the model, using GA as a tool to determine the unknown parameters, reproduces the experimental data with only reasonable accuracy and was relatively insensitive to the parameters. Results of the flocculation study showed that increases in polymer dosage had greater effect on the time required to reach the maximum floc size than on the floc size itself. It was also determined that, given all the aforementioned parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on the floc growth.

Jan 1, 1993

By H. Vuthaluru, O. Kavianipour, C. -Z. Li, N. Suresh, D. Sahu

The paper describes a CFD model developed for 76mm Dense Medium Cyclone (DMC) using Ansys Fluent Software to gain insights into the separation of particles according to their size and density. The simulation used in this paper includes the Reynolds stress model to predict the turbulence inside the cyclone body. An Eulerian-Eulerian multiphase CFD model was applied to model a number of physical aspects such as the separation of coal particles and the segregation of magnetite media solids. The experimental results generated in a laboratory scale DMC were used for the validation purpose and the predicted results of CFD have been validated for the flow splits of water, magnetite and coal. The simulation results obtained from the Eulerian-Eulerian multiphase model revealed that the prediction agreed with experimental results, and matched reasonably well in terms of the mass flow rates of water, magnetite and coal. Furthermore, the partition curve of the DMC when mapped for the separation of - 3.0+0.50 mm size also showed to be in agreement with the experimentally obtained curves. The gravity of cut (SG50), also predicted by the Eulerian-Eulerain multiphase CFD model, was found to be in the vicinity of observed experimental value of SG50. Keywords: Dense medium cyclone, Eulerian-Eulerain multi-phase modelling, computational fluid dynamics, cut gravity (SG50)

Jan 1, 2020

By C. E. Abbey

Cobalt, iron and manganese play various roles in copper electrowinning using lead–calcium–tin alloyed anodes. Cobalt catalyzes electrochemical water decomposition resulting in lower anode potential and reduced corrosion rates. Iron reduces cathodic current efficiency, but is used to reduce higher oxidation states of manganese that oxidize organics in solvent extraction. Manganese also produces anode scale and is generally considered a problematic impurity. The effect of the combined interaction of these three metal ions on the anode potential has not been quantified yet. The current work used a three factor, two level, three replicate central composite design of experiments to analyze the effects and potential interactions among cobalt, iron and manganese. The experiments consisted of chronopotentiometric analysis to assess anode potential after 24 h of operation. Higher [Co], lower [Mn] and either high or low [Fe] yielded lower anode potentials. Two regression models were developed to predict anode potential as a function of [Co], [Fe] and [Mn]. A method to estimate electrical energy consumption for copper electrowinning is also presented.

By W J. Riva

This paper reviews the circumstances that led to the development and construction of a commercial-scale vertical shaft carbonizer at Conmore, Alberta. This form coking process may be regarded as having potential application in other areas. Coal pelletizing offers a promising method of decreasing coal agglomeration costs under certain circumstances. Pellets can be rolled easily from -35-mesh coal, provided that a minimum of -200-mesh coal is present. Bentonite was found to be the best binder and was most effective when added in amounts of about 2 per cent. The water content of the coal pellets was observed to vary from 18 to 23 per cent. As a by-product of this investigation, it seems possible that fine coal could be converted into stoker feed by this process. A short investigation of the effect of heating rate on the carbonization of pellets was conducted. The low maximum heating rates in certain temperature ranges, necessary to avoid crack formation in the pellets as reported by other

Jan 1, 1964

By E. J. Gleim

A study of the records on file in the Bureau of Mines reveals that moray fire in coal mines have been started by electrical equipment or circuits. There the fires were of undetermined origin, electricity often was Strongly suspected as the probable cause. While it is unfortunate that positive evidence as to the cause is so often lost in the general destruction resulting from fires, there are many lessons to be learned from fire s in which the origin was definitely established as electrical. For modern high-speed methods of producing coal, electrically operated machinery has become virtually indispensable underground. With increases in the amount of equipment it has not always been necessary to increase the number of circuits in the mine where direct current is mainly used, but it has been necessary to increase the carrying capacity of these circuits. For example, lends such as heavy-haulage units drawing 1,000 amperes or more have brought boat the introduction of 6/0 and "No. 9 section" trolley wires. This has not made the task of fire prevention any easier, for it has meant that circuit breakers s must be set so high that partial short circuits fail to open them, therefore an arc of considerable proportions can be maintained without causing the, beaker to open. Thus, if as fall of roof brought a trolley wire down against a loaded car of coal, an arc might be struck that would ignite they cowl without opening the circuit breaker.

Jan 1, 1937

By Morgan B. D

Since the mid 1950s, limonite deposits of a new type have been found in the northwest of Western Australia. The deposits consist of extensive fossil valley fillings up to several hundred feet in depth, of medium to high grade limonite, frequently containing limonitized fossil wood, and of Mesozoic or Tertiary age. The distribution of the deposits is closely linked with hilly outcrops of Archaean and Proterozoic jaspilite in the headwaters of the old valleys, from which the iron has been derived by leaching, and presumably re-precipitated by a process not unlike that which operates in forming bog iron deposits. Due to the relative resistance of tlie limonite to erosion, the rejuvenation of streams in the area in recent times has left limonitic remnants as mesas up to· several hundred feet above the levels of the present creeks, the courses of which generally are adjacent to or within a few miles of those of the old limonite filled valleys.The Robe River limonite deposits are the largest of this type known and can be traced for approximately 130 miles along the old stream, over 30 sq. miles of limonite remnants remaining at the present time.The present quantity of limonite in this system alone is probably in excess of 5,000,000,000 tons, and the original quantity must have exceeded four times this tonnage when allowance is made for erosion.Some thousands of millions of tons of this material contain in excess of 54 per cent Fe, with approximately 10 per cent combined water. The chief impurities are SiO2 and Al2O3, and minor elements are not present in objectionable amounts. A portion of these deposits was extensively tested by The Broken Hill Proprietary Company Limited (the B.H.P. Co. Ltd.) during 1962-1964. Most of the data presented in this paper are based on the work done on these deposits which are typical of those discussed. The overall problem of the origin of the limonite is discussed. It is apparent that the limonite originates from the jaspilitesof Archaean and Proterozoic age which form the highlands at the upstream ends of the deposits. The iron oxide has been chemically and/or mechanically derived from these jaspilites and deposited by one or more of the following mechanisms.A.-Chemical-sedimentary mainly by biological agenciesB.-Replacement of fluviatile sediments by iron-charged watersC.-Clastic sedimentary processesD.-Lateritization of fluviatile sediments.These various mechanisms are discussed; the authors favour machanismA.Manuscript received' at The Institute, 14th July, 1964.

Jan 1, 1964

By T. N. Matveeva, T. A. Ivanova

"The article presents the results of the research aimed at development and testing of new effective reagents – collectors and green modifiers for more complete extraction of gold and platinum to concentrates at reduced loss with waste products. The main deposits of Au and PGM ores of Russia and abroad are presented by refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold and platinum, the low metal content, non-uniform distribution of valuable minerals. and show low indicators of recovery. The main losses of precious metals (up to 15 %) at flotation are associated with thin slam tailings because of inefficiency of standard reagent modes.In the paper, the new trends in design of collecting agents for extraction of gold and PGM sulfide minerals and their application in flotation tests are substantiated. The original technique for obtaining the modified collector reagents – dithiocarbamate, dithiophoshpinate and dithiazine, incorporated non-ionic compounds that are able to generate stable complexes with gold and platinum has been developed. A novel class of collectors – cloud point polymers showed high flotation recovery of fine particles of gold and platinum. The original technique to create the mineral samples of natural sulfides with ""invisible"" or sub-micron gold on their surface designed helped to indicate the mechanism of selective adsorption of novel agents on Au and Pt-sulfide minerals. Extractive UV spectrophotometry, potential measurements, X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy were applied to analyze the adsorbed layer of modified reagents on the mineral surface. Selective hydrophobic covering on the surface of micro- and nanoparticles of noble metals provided an increase in their extraction during flotation. New reagent modes of modified collectors and green modifiers were tested in scaled-up laboratory flotation and the results obtained demonstrated the increased quality of the concentrates in terms of gold content by 1.5 times and higher gold recovery by 1.5-5%. The studies have been supported by Grants of the President of RF “Scientific School of Academician Chanturiya” NSh-220.2012.5; NSh-748.2014.5."

Jan 1, 2018

The SART (sulfidisation, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide from each other in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation I reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulfide to copper molar ratio of around 0.56, a pH of 4, and a minimised cyanide to copper molar ratio. The experiments also showed that thickening time may have drastic impacts on SART performance.

Jan 1, 2011

Jan 1, 2005

By N Guresin, A Cooper, L Lorenzen, H Muller, S C. Dominy

Sampling and metallurgical test work during various phases of engineering?studies?is of?paramount importance for a robust processing plant design. When developing a process flow sheet, risks in achieving desirable financial outcomes are minimised by ensuring appropriate sampling and adequate metallurgical test work supports the engineering and cost estimation at each phase of project development.The quality and type of samples used for metallurgical test work are just as important as the metallurgical test work itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should take into account the spatial orientation, lithology, alteration, degree of oxidation, mineralogy and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical test work program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design.Snowden has observed that the quality of sampling and quantity of metallurgical test work carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are often the result of the plant design based on benchmarks of apparently similar orebodies or buoyant metal prices supporting cash flows until rectifications can be implemented.The paper will discuss important aspects of sampling and test work required for engineering studies in designing process plants based on industrial case studies.CITATION:Guresin, N, Lorenzen, L, Dominy, S C, Muller, H and Cooper, A, 2012. Importance of effective sampling and test work protocols for process plant design, in Proceedings Sampling 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

The drilling and evaluation of bore cores provides the best available statistical basis for characterizing a coal prospect. Important, long-term decisions by management frequently must be based on the results. The majority of coal mined presently is used for steam raising or the production of metallurgical coke. Common bore core tests and analyses appropriate to this usage can be cate- gorized as non-destructive, chemical, physical, petrographic, caking/plastometric and propert- ies of non-coal material. The major tests within each category are described. Certain specific information from the bore cores is required by the coal geologist, mining engineer, coal preparation engineer and the user, either individually or as a group. The optimal bore core evaluation test pro- gramme is the one which satisfies the needs of all the professional disciplines with the grtatest speed and at minimal cost. The principal steps in such a programme are listed. There is an urgent need for a bold new Australian standard to provide the necessary guidelines to an industry which at present lacks uniformity in its approach to the task.

Jan 1, 1977