Search Documents

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By T Schrimpf, I Bryan

The life cycle of a mining project begins with initial regional exploration and ends with mine closure and rehabilitation. Between resource definition and the commencement of mine construction is the study phase. In this phase technical concepts and processes are defined, evaluated and assessed with the aim of establishing whether the deposit is economically feasible. The study phase usually involves various steps from a concept/scoping study to prefeasibility and ultimately definitive feasibility study. The complete study phase can take several years. Although the costs for studies are low in comparison to actual construction and operating costs of a mining project, they are significant especially for junior exploration and mining companies advancing projects to the point of being funded.The studies aim to determine selected parameters for the project, eg mining and processing methods, operating strategy, etc and provide a roadmap for project development ahead. Although mining studies are of the utmost importance for the mining project and the project owner, they are usually carried out using a conventional engineering approach: the consultant or design engineer works to a defined scope of work. The resulting design might be based on good engineering, but might often also fail to provide the solution for the project owner that delivers the best shareholder value. An alternative to this more traditional approach to project evaluation is what we have termed a value engineering approach. Value engineering is a creative, organised effort, which in the case of a mining study analyses the requirements of the study for the purpose of achieving the essential outcomes with the highest shareholder value. The outcome of a study is a concept that delivers the highest achievable value of the resource project and shows the way ahead to realise this value. Through a group investigation by experienced, multi-disciplinary teams the value of the resource is improved through the study of alternative options, methods and processes. The scope of the study is not limited to a narrowly defined engineering scope, but to the creation of value.The study commences with the identification of key value drivers and risks, based on the available information (drill data, geotechnical data, metallurgical test work, etc). This enables the quantification of key uncertainties, risks and value adding opportunities. Study efforts concentrate on key value drivers and are not unnecessarily spent on side issues. This approach can significantly reduce the time frame and costs for the study phase.This paper describes in more detail RMDSTEMÆs value engineering approach to mining studies and illustrates it with examples and case studies.CITATION:Schrimpf, T and Bryan, I, 2012. The application of value engineering principles to mining studies, in Proceedings Project Evaluation 2012 , pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

As has been the case since the early Phoenician traders, the minerals used by modern man come from deposits scattered around the globe. The price received is more and more being set by worldwide supply and demand. Thus the price component in the profit equation:Profits = Material sold (units)x(Price/unit û Cost/unit) is largely determined by others. The recent price history for two of the major metals, copper and iron, are given in Figures 1 and 2, respectively. As can be seen there has been a steady decline in the prices (when expressed in constant dollars) over the 20 years which have lapsed since the first of the International Conferences on Mass Mining, æDesign and Operation of Caving and Sublevel Stoping MinesÆ was held. If one would look back over the entire 20th century this would also be the trend. Cost containment/reduction through efficient, safe and environmentally responsive mining practices is serious business today and will be even more important in the future with increasing mining depths and more stringent regulations. A failure to keep up is expressed very simply as: Profit This, needless to say, is unfavourable for all concerned (the employees, the company, and the country or nation). The mining companies have had to look at ways of reducing the expense part of the profit equation while maintaining safe, environmentally conscious operations. Table 1 summarises the rules for working in todayÆs economy.

Jan 1, 2000

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By H. C. Gunning

In spite of the fact that mining has been more or less active in the northern part of Vancouver island since the late 'nineties', there seems to be a remarkable lack of information regarding the nature and development of the region. Recently the operations at the Old Sport mine of the Coast Copper Company, Limited, and spectacular copper discoveries in the vicinity of Nimpkish lake, have directed the attention of the mining fraternity to the district. The writer spent the summer of 1929 making a reconnaissance examination of the general geology and mining properties of the area between Quatsino sound and Nimpkish lake, and he feels that a short paper describing the nature and mining possibilities of the region should be of interest at this time. A more detailed account of the ?geology and of the mining properties will be published in the forth- coming Summary Report of the Geological Survey. A short paper dealing with the Nimpkish Lake district was presented at the Annual Meeting of the British Columbia Division, held recently in Vancouver.

Jan 1, 1930

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By Hongyang Cao

The iron constituents selectively separated from the modified copper slags by magnetic separation and flotation.were studied. The results of magnetic separation for modified copper smelting slags show that the grinding size, current intensity and dispersant agent had great influence on grade, and recovery ratio of TFe in preparation concentrate; The results of flotation for magnetic concentrate show that the positive flotation of sodium oleate negatively upgrade the grade of magnetic concentrate, but the reverse flotation of lauryl amine and soluble starch are effective. The grade of TFe can reach 54% and the recovery ratio can reach about 90% in magnetic concentrate, when the grinding size is 45.8µm and the current intensity is 2.5A. The optimal effect is obtained by using lauryl amine as collector and soluble starch as depressant to reverse flotate magnetic concentrate, and the grade of TFe is upgraded 2.37%.

Jan 1, 2009

By William J. Pardee, Michael A. Shaff

"Deeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will accelerate productivity growth and materials science application through the ease with which they can be modified to accept new materials knowledge and sensors. Carbonization of resin matrix carbon fiber composites, specifically, is a violent solid state chemical reaction with large stresses due to gas pressure, matrix shrinkage, and differences in thermal expansion. The matrix strength falls sharply, then rises again during the process. At least two competing reaction paths are important; the first cleaves methylene bonds, reduces toughness, density and stiffness; the second reforms those bonds, ultimately resulting in aromatic ring condensation that increases density, strength, and modulus. Since these reactions have different temperature dependencies, one can expect to shift the process towards the second path by changing the heating rate, but that change must be accomplished without producing macroscopic interlaminar crack growth. To accomplish this, we employ gas sensors to infer matrix chemical state and acoustic emission to identify microstructural changes and to recognize brittle fracture. The latter does not prevent delamination, but is important in testing models for the causes of delamination and in improving the processing cycle. This paper describes a control strategy to accelerate the process while still lowering the risk of failure.IntroductionDeeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will be more easily modified to accept new materials knowledge and sensors, thus accelerating productivity growth. Such a control strategy for carbonization control is described below.Carbon-carbon composites are time consuming and costly to manufacture. Processing methods have been developed empirically and are usually very conservative because the process often fails when any change is made. Apparently minor changes in materials or geometry can produce failures that are difficult to diagnose and correct. We will describe below several essentially unavoidable sources of variability. These are best dealt with by applying materials science to adapt (i.e., closed loop control on materials properties) the process in real time to reduce the effect of unavoidable model idealizations, material variability and environmental noise. The most critical issue in control of the carbonization process control is avoiding catastrophic delamination. The strategy developed below makes use of a priori materials knowledge and real time sensors to accelerate the now very slow process without destroying the material, and without requiring unreasonable resources to determine the statistical properties of the material."

Jan 1, 1988

By AIME AIME

THE meeting of the Petroleum Division at Houston, Oct. 10-12-headquarters, Rice Hotel-was preeminently a technological success. Two hundred and twenty-five attended the Thursday morning session and approximately 200 attended the sessions on Thursday and Friday afternoons and Saturday morning. Harry Power, Chairman of the Division, in his opening remarks, credited Paul Weaver and M. Albertson, respectively chairman and vice-chairman of the local committee, with working long and prodigiously in organizing the program. The theme of the initial session was indicated by Mr. Albertson in a statement relative to the estimation of developed petroleum reserves. He said that the problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became an acute one. Mr. Albertson gave some of the more important reasons for this situation. Since the decline-curve method became inapplicable, the volumetric method has become the chief one used. It depends on the factors of productive formation volume, porosity, saturation, and recovery. He briefly discussed the factors necessary for application of the volumetric method. P. P. Gregory discussed the estimation of petroleum reserves in prorated lime¬stone fields (see his paper in the October

Jan 1, 1935

By George D. Dub

The Bureau of Mines, in connection with the investigations of war minerals it conducted, examined the graphite deposits of this country, studied the methods of mining and preparation used, and sought to devise more efficient methods for the preparation of domestic graphite, and to standardize the quality of the product. The graphite investigations covered three general phases, as follows: 1. An examination of the deposits in Alabama and other States, and a survey of the methods of mining and preparation used. In this connection methods of sampling and analysis were noted and experiments made to determine a standard method of sampling and a, rapid but accurate method of analysis. 2. Experimental work on the concentration and refining of domestic crucible graphite to improve the quality of the product and to lessen waste. 3. Experimental work in crucible manufacture to determine the properties of domestic flake and the maximum proportions that might be used without impairing the quality of the crucibles. This work was accompanied by photomicrographic study of crucible structure.

Jan 1, 1920

By N Madani, Y Abildin, E Topal

Mine planning is a crucial part of all mining industry projects, and nowadays, geometallurgical mapping through advanced computer technologies provides an opportunity to involve metallurgical responses of a deposit into 3D block model in order to optimise mine planning activities, especially for production forecasting. Including these metallurgical parameters apart from traditional geology and grade-based attributes into resource modelling leads to an extensive approximation for the economic maximisation of mine production due to better forecasting, planning and increasing certainty and the reliability of the resource model (Macfarlane and Williams, 2014). Commonly, geostatistical techniques and algorithms are used to produce models with the high resolution (Brissette et al. 2014; Deutsch et al. 2014; Tolosana-Delgado et al. 2015). The accuracy of the modelling procedure deeply depends on a reliable block model, produced by spatial analysis of corresponding variables that define the geological, metallurgical, mineralogical and chemical behaviour of the deposit. However, there are special cases, where the application of enhanced geostatistical methods is required, to solve the occurred difficulties between variables with multivariate complexities. For example, in oxide copper deposits, the soluble copper grade is a percentage of total copper grade and recoverable by heap leaching processes (Emery, 2012; Hosseini and Asghari, 2015). Hence, the joint spatial modelling of these variables has two difficulties.CITATION:Abildin, Y, Madani, N and Topal, E, 2018. Forecast the mineral processing destinations based on spatial interpolation of geometallurgical variables, in Proceedings Complex Orebodies Conference 2018, pp 2–5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Renan Bueno Wojciechowski, Yukio Shigaki

The quality of flat rolling process depends highly on multiple factors such as applied forces, materials involved for both strip and rolls, roll geometry and its positioning. To calculate the strip shape, a mathematical/numerical model can be applied, showing the final product and how the equipment behaves when changing some parameters. This is usually a time-consuming task for both user and computer, especially when it involves thin and hard strips. By coupling a quick rolling load calculation method as Bland-Ford and Finite Element Method (FEM) for roll stack deformation, it is possible to create an accurate and user-friendly rolling simulator. This paper presents the improvements done in the 3D FEM/multi-slab method and its actual capabilities by simulating two cases of a 6-High rolling mill. Different analysis in this equipment can be easily done in about 10 minutes by using the developed an electronic spreadsheet program interface and the folder generated with relevant results and logs. An operation manual and a commercial FE program plugins were made to aid construction of a completely new model. The code was created in a modularized way to assist the application of this simulator for other operational conditions.

Oct 1, 2019

By J. K. Afidenyo

Microbial pretreatment of a double refractory gold ore was investigated using a white rot fungus, Coriolus versicolor (ATTC 20869) to improve gold extraction. A series of preliminary tests were conducted to determine the amenability of the ore to fungus degradation. Pulp density, temperature, pH and retention times were the process variables considered. Both a single. Stage and two-step processes were studied to establish process conditions. During the single stage process, the ore was contacted with the fungus culture (biotic) for 3weeks at 30°C and pH 10.0. For the two-step process, the first step involves ore contact with the culture medium (abiotic) at 45°C and pH 10.0 followed by fungal contact (biotic) at 30°C. Results indicated that carbonaceous matter is not degraded but passivated by the fungus; as preg-robbing activities dropped significantly from 18.1% to below 1.0%. The single stage process resulted in higher gold recovery than the two-step process Gold ex-traction by cyanidation of the pretreated ore was 78.9% for the single stage compared with 15.0% for the untreated ore. In the two-step process, only 73.3% gold extraction was achieved. Application of the two step process conditions to a high grade flotation concentrate, resulted in 93.3% gold ex-traction as against untreated concentrate of 30.5%. The results show that the microbial pretreatment process degraded sulfide sulfur, passivated carbonaceous matter and enhanced gold extraction from double refractory gold ore and concentrate.

Jan 1, 2014

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By T. Y. Chong, J. A. Folinsbee

Since milling began in 1909, the PJV Dome mill has been expanded several times, to the current throughput of 11,500 tonnes per day. PJV recovers free gold using crushing and grinding followed by gravity concentration. The remaining gold in the gravity tails is recovered by cyanide leaching followed by Carbon-In -Pulp processing. Prior to 1993, cyanide tailings were impounded in the tailings pond where cyanide was allowed to degrade naturally. Effluent was discharged seasonally during the summer and early autumn to maintain the water balance. In 1993, an Effluent Treatment Plant (ETP) was designed and constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO SO2/Air cyanide destruction process was added to the ETP. Even though the ETP was successful in meeting the cyanide, metals and total suspended solids (TSS) discharge limits, often the treated effluent failed to pass toxicity tests. Following successful laboratory and plant scale testing, the addition of the chelant EDTA (ethylene diamine-tetra-acetic-acid) was commenced in the 1999 operating season. To date, discharged effluent has passed all toxicity tests. This paper describes the evolution of the ETP from its early conception to the various phases of upgrade needed to meet the MISA discharge limits.

Jan 1, 2005

By J. Peterson, D. D. Tannant, J. Todd

"A review of blast designs and improved blasting practices at the EkatiTM diamond mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine’s well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. EkatiTM uses 270 mm holes for production blasting, and 165 mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion/ANFO blends. The mine plan involves using 30 m double benches. A 30 m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15 m benches. This paper summarizes the monitoring equipment and data gathered to date. IntroductionThe EkatiTM diamond mine is located about 300 km northeast of Yellowknife, Northwest Territories, Canada. The mine is a joint venture of BHP Diamonds Inc. (80%) and geologists Charles Fipke and Stewart Blusson (10% each). The EkatiTM mine is Canada’s first diamond mine and BHP is the operator. The mine is accessed by air and by a winter ice road.The first kimberlite pipe mined at EkatiTM is known as the Panda pipe. The Panda open pit mine will have a total depth of 315 m (Fig. 1), a width of about 600 m, and a 50° overall slope. Initial ore production is 9000 tonnes per day.This paper summarizes the pre-strip blasting and the evolution of the production and wall control blast designs from 1997 to 2000. The initial blast designs and the rationale behind subsequent changes that took place are presented along with the techniques currently in use.The paper also briefly presents an experiment done to measure the rock mass response to blasting. Three blasts were instrumented with geophones, gas pressure sensors and time domain reflectometry cables. A brief summary of the instrumentation and data gathered is included."

Jan 1, 2001

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014