Search Documents

By Kym Runge, Wei Huang, Fengnian Shi, Christian Antonio

"This paper presents an emerging High Voltage Pulse (HVP) technology for ore pre-treatment. Unlike previous studies where HVP was utilized as a crusher to pulverize ore particles to micron size ranges for downstream processing, the researchers at the Julius Kruttschnitt Mineral Research Centre (JKMRC) use HVP to enhance ore processability. Application of relatively low levels of HVP energy to selectively break mineralized particles from barren rocks, followed by size-based screening separation enables the feed ore to be split into high grade and low grade products. During HVP treatment, cracks/micro-cracks are generated which results in pre-weakening of the treated ore particles, which ultimately results in energy savings in the downstream comminution processes. HVP treatment followed by conventional grinding also results in improved liberation of the valuable minerals in comparison to that achieved with traditional conventional comminution, subsequently improving downstream separation efficiencies. The three major improvements in ore processability through HVP pre-treatment have the potential to facilitate rejection of low grade ore prior to processing, increase production rates, reduce the energy required for comminution and improve flotation separation recoveries. This paper summarizes the major research outcomes of HVP pre-treatment demonstrated using ores from various mining operations conducted by the JKMRC. It also discusses the barriers that must be overcome before it can be adopted by industry with confidence in a continuous high tonnage rate application.INTRODUCTIONThe challenges of declining ore grades and increased plant throughput rates, resulting in higher energy consumption and operational costs, require the mining industry to adopt new technologies to make future ore treatment economically viable. Over the past 50 years, many researchers have engaged in investigating novel comminution techniques. Since Yutkin (1955) first demonstrated the potential to generate shock waves with pressures exceeding 103 MPa via electrical breakdown of water, several applications of electrohydraulic crushing by shock waves have been reported (Curley-Macauly, 1968). Interest in this technique was bolstered when Andres (1977) demonstrated that electrodynamic fragmentation results in superior liberation of mineral grains as compared with conventional grinding techniques. Despite mounting laboratory-scale evidence of the efficacy of electrodynamic fragmentation for mineral liberation, development of the technology for full-scale operation has stalled, primarily because the energy required to achieve desirable mineral liberation is approximately two to three times that of mechanical comminution, amounting to approximately 100 kWh/t for typical mineral ores (Andres et al., 2002)."

Jan 1, 2018

By Anthony Konya, Calvin J. Konya

This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

Feb 1, 2020

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By J. Rafael Otaíza, Francisco Mardones

This work has addressed the problem of creating a predictive model of the maximum particle velocities in the rock mass (PPV). The model designed specifically can model the subsequent vibrations of blasting based on geometric parameters, explosive loading, and the blasting process itself. Models based on artificial intelligence (AI) algorithms can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. These models have been successfully used in similar contexts (Prashanth, (2018)) and have achieved state-of-the-art results in the field (Lawal, (2021)). The main challenge is to adapt them to the context of Chilean mines, in addition to including the geometric information of the blasting and the heuristic to obtain the set of optimal parameters, it is proposed to follow the work of (Simonyan, (2013)) and obtain "saliency maps" adapting it to tabular variables. We implemented an Artificial Neural Network (ANN) with a large number of neurons in the hidden layers. Models based on neural networks can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. The literature shows that, for the problem of rock type identification, basic neural networks perform well (Simonyan, (2013)), but lack uncertainty estimates. This is a data-driven model, and in this sense, the model training was carried out using data from multiple operations in the large copper mining industry in Chile. In these databases, data consistency and the balance of the various independent variables that have the greatest impact on the model were ensured. With the above, the optimal hyperparameters of the model were determined, obtaining a predictive R-squared of 0.94.

Jan 21, 2025

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By E. Lee Cameron

The old mine workings on four barite-fluorite veins of the Lake Ainslie district, Nova Scotia, were opened recently and channel sampled. The samples were then forwarded to the Ore Dressing Laboratories, Bureau of Mines, Ottawa, for chemical analyses. Following the analyses, the sample rejects were combined to form bulk samples, representing ore from each vein, for small-scale batch test work. Tonnage samples from the veins, for pilot mill testing, were submitted when requested by the Bureau. The results of the analyses on the channel samples showed that there are two grades of ore in the di strict, represented, for test purposes, by the Trout River vein and Johnson vein ores. Small-scale and pilot-plant test work was undertaken on both these ores. The Trout River ore is amenable co concentration but, because of the high-barite-co-fluorite-co-calcite ratio, a fluorite concentrate was not obtainable from the Johnson vein ore as received. However, Johnson ore blended in a 1 :1 ratio with Trout River ore gave a mill feed that was readily concentrated. The test work on these ores showed that the following concentrates are obtainable : (a) A barite concentrate, with a recovery of 85 to 95 per cent of the available barite, analysing 93 co 96 per cent BaS04, 4 co 6 per cent CaF,, and 0.5 co 2 per cent CaCO3. (b) A fluorite concentrate, with a recovery of 80 co 85 per cent of the available fluorite, analysing 94 to 97 per cent CaF, , 1 to 3 per cent BaSO., and 1 to 3 per cent CaCO3

Jan 1, 1945

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By Alexander May

The U.S. Bureau of Mines investigated the application of oxidation-reduction potential (ORP) and pH measurements to environmental studies of mining and mineral processing wastes, and developed a computer program to estimate the concentrations of species of lead present in samples from a lead processing waste site. The methods and techniques for the ORP-pH measurements were investigated using known standard solutions made in the laboratory, samples from a ferric oxide waste disposal pond at a rutile production plant, and samples of well water and stream water from the lead processing waste site. ORP values were measured from 5 to 80 °C, from pH 1 to pH 12, and at various ratios of oxidant to reductant. The ORP-pH values can help identify valence values and species of ions present, including those of major, minor, and trace concentrations, and also indicate possible reactions at various pH values. The ORP measurements versus temperature yield data from which thermodynamic values can be calculated. The application and limitations of these measurements are discussed, and a brief discussion of the computational program to identify species of lead is presented.

Jan 1, 2010

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By H. M. . van der Donk

In this work an overview is given about the techniques available for the removal of metallic impurities from molten aluminium. The overview is focused on the removal of iron. Also, some experimental results are given about the creation of iron-rich intermetallic compounds in an aluminium system, which are subsequently removed by gravity segregation and filtration techniques. This work is part of an ongoing research project of three major European aluminium companies who are co-operating on the subject of recycling of aluminium packaging materials recovered from household waste by means of Eddy-Current techniques. Using this technique the pick-up of some contaminating metals, particularly iron, is almost unavoidable.

Jan 1, 1995

By Xinzhong Deng, Naixiang Feng, Kejia Liu, Jianping Peng, Yaowu Wang, Yi Zhang, Yuezhong Di

Low-carbon Ti2O3 was prepared by carbonthermal reduction of the mixture of titanium dioxide and activated carbon at vacuum condition. The kinetics and phase evolution of Ti2O3 formation process were investigated through X-ray diffraction and gravimetric analysis. The only intermediate phase detected is Ti3O5. The reduction time was reduced sharply to 4 h when temperature was raised to 1300 °C. The best molar ratio of activated carbon and TiO2 is 0.6–1. At this condition, the content of Ti2O3 in slag is up to 95.63% and the content of the carbon element is below 0.004%, which meets the requirements for the further preparation of metal Ti by FFC Cambridge process. At the same time, the microstructure of Ti2O3 generated presented porosity, which would promote the electro-deoxidation process extremely.

Mar 1, 2017

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes. Water is routed to the roof bolter from the main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/m3, and during the cleaning of the dry box the average respirable dust concentration was 1.188 mg/m3. The silica content of the roof material was high, ranging from 28.9% to 52.7% during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60%when cleaning the collector boxes. INTRODUCTION Currently, the dry vacuum dust collection system is the standard dust collector on roof bolters in underground coal mining. It has been proven to be an effective dust control to prevent roof bolter operators’ overexposure to coal mine respirable silica dust during roof bolting operations [Potts eta l, 2011 and Colinet, 2013]. The dry collection system works as follows: drill cuttings are vacuumed into the precleaner. The precleaner dumps oversized material onto the mine floor while undersized material enters the dust box via vacuum airflow produced by a blower. The cuttings entering the dust box are either deposited on the floor of the dust box or into a dust collector bag. The vacuum airflow leaves the dust box through a final filter which removes any small particles from the airflow. Figure 1 shows the internal view of two dry collection system boxes; one that does not use the dust collector bags and another that uses the dust collector bags. Dust collectors that use dust collector bags to contain material inside the dust collector box have been shown to provide better protection to roof bolter operators than dust collectors that do not use the bags [Listak and Beck 2008]. The dry collectors are very efficient at reducing respirable coal mine dust exposure from roof bolting activities. Recently, Blue Mountain Energy’s Deserado underground coal mining operation, outside Rangely, CO, made a modification to the dry collector system to convert it to a wet collector system with a unique exception from the Mine Safety and Health Administration (MSHA) for testing purposes. The wet collector system still uses a vacuum system to pull material from the vertical roof bolt hole, but incorporates a water spray nozzle located inside the dust box to wet the incoming material. The flow through the nozzle ranges from 1.9–7.6 lpm (0.5–2.0 gpm) at 0.69 MPa (100 psi). The conversion to the wet collector system removes the precleaner and the cyclones inside the dust box. The wet material (sludge) then empties through a specialized valve in the bottom of the box. The final filter is still used to prevent respirable dust from leaving the dust box through the exhaust. During operation, the wet collector dust box is opened and hosed clean after roof bolting every place. After every two entries the final filter is changed out. Figure 2 shows the inside of the wet collector box.

Jan 1, 2019

By W. R. K. Wu

This bulletin traces the development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of the pertinent literature. The bulletin was written as a part of the Bureau of Mines research program on synthetic liquid fuels. It covers the history and economics of the process; the chemical aspect of hydrogenation of coal, tar, and middle oil; the engineering aspect of converting coal and tar to liquid fuels, principally gasoline; and the equipment for the process. The literature covered includes documents of the United States and British Governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.

Jan 1, 1968

By Carlos Zevallos, Julia Zea, Francisco Alejo

Este estudio evaluó la recuperación de cianuro utilizando polipropileno (PP) y politetrafluoroetileno (PTFE) y el impacto de las condiciones de operación con aguas residuales mineras sintéticas y reales. Los resultados muestran un mejor rendimiento de la membrana con la membrana de PTFE frente a la membrana de PP, así como una impacto del pH del destilado, la temperatura y la concentración de cianuro de alimentación en la eficiencia del proceso. En cambio, concentraciones de cianuro destilado mostraron un impacto muy limitado en el rendimiento del proceso, lo que sugiere un impacto limitado. Se requieren recursos de agua dulce para la recuperación de cianuro.

Sep 29, 2023

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By Brent C. Jellicoe, Phil Robertshaw, J. Murphy, Peter Williamson

Kimberlites and associated diamonds have been the focus of extensive exploration in central Saskatchewan since 1988. During 1989, Uranerz Exploration and Mining Limited identified 71 shallow magnetic anomalies in the Fort a la Corne area from detailed aeromagnetic surveys. By the end of 1991, 18 of these targets had been proven, by drilling, to be kimberlite bodies encased within Cretaceous sedimentary strata. From 1991 to 1997, the number of drill-confirmed kimberlite bodies increased to 69. Our current view, drawing on an integration of geophysical and geological information, is that the kimberlites are composed of individual bodies and multi-vent clusters of coalesced bodies, all apparently constructed of stacked, temporally distinct layers of pyroclastic crater-facies kimberlite. Diamond recoveries and geochemical results from associated heavy minerals at Fort a la Corne remain highly variable, although continued minibulk sampling is expected to improve the estimation of diamond grades for the most prospective bodies.

Jan 1, 2001