Search Documents

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

By Albert F. J. Bordeaux

(Cleveland Meeting, October, 1912.) THE immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia, would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development, of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or ire even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a snap of Eastern Siberia, showing the mineral deposits.

Oct 1, 1912

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U. S. Department of the Interior, to stimulate greater interest in safety in the mineral-extractive industries and to encourage the development of more effective accident-prevention programs. Since its beginning in 1925, thirty-four safety contests have been conducted. This publication reports results of the 11 annual contests for the period 1948-1958, inclusive. Mineral operations awarded the "Sentinels of Safety" trophy for the best safety record in their competitive group as well as those ranking second, third, fourth, and fifth are listed along with a summary of their achievements in preventing disabling injuries. In addition, this publication contains statistical information reflecting the disabling work-injury experience of all other mines and quarries enrolled in the annual contests. The injury statistics of these operations are arranged in the six groups of the competition and through 1955 are the only data on injury-severity at noncoal mineral operations published by the Bureau of Hines. Recognition of the National Safety Competition in promoting safety has increased steadily during its 34 years. The number of plants participating in these annual competitions increased from 210 in 1925, its first year, to a record of 675 in 1958. The expanding scope of the National Safety Competition indicates that more mines and quarries in the United States are enrolling 90 all available means to promote safety on the job will be used. Safety contests like this are generally recognized, in the field of safety promotion, as an effective way to arouse and hold the interest of employees and officials in accident-prevention programs. They tend to forge individual precautionary acts into group action centered on a common objective, such as winning the ?Sentinels of Safety? trophy.

Jan 1, 1960

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at NIOSH’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six different water sprays at pressures ranging from 689 kPa (100 psi) to 6,895 kPa (1,000 psi) in a 14.5-m3 (512-ft3) confined dust chamber. Testing was conducted to determine the effect of various pressures on each spray’s respirable coal dust knockdown ability. It is known that higher water pressures are typically preferred for lowering airborne dust concentrations, but it was important to determine at what pressure range the dust knockdown ability of each spray plateaus or reaches its minimum dust concentration. Results from this testing showed that several sprays saw up to 100% decrease in dust concentrations during the five-minute water spray testing period, with some occurring well below the maximum 6,895 kPa (1,000 psi) spray pressure.

Feb 1, 2023

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015

By Suresh P. Babu, Joseph W. Leonard, Richard Muter, D. P. Sen

OUTLOOK FOR COAL UTILIZATION In 1975, about 650 million tons of bituminous coal and lignite mined in the United States was used to meet 55% of the primary energy input for electric power generation and 26% of the total industrial consumption.1 Even though this amounts to only 21% of the total energy requirements, it is believed that with the declining natural gas resources and uncertainty of liquid fuel imports, coal will assume a more dominant role in suppplying our future energy needs. A regional breakdown of the coal reserves of the United States along with their characteristics is shown in Table I. At present the United Stares Energy Research and Development Administration (ERDA) and the US Bureau of Mines (USBM) are financing extensive research programs in advanced mining methods and energy conversion processes. The increased demand for wal which may result from these research programs may also create large-scale environmental protection problems. As more and more coal is mined the production of undesirable coal fines and dust also increases proportionally. The USBM and the Environmental Protection Agency (EPA) research in this field includes development in the areas of instrumentation for qualitative and quantitative analysis of wal dust, protective devices, and dust collectors. Dust control by water sprays, steam, and foam are also being investigated. Other aspects of safety in mining include developing methane drainage techniques prior to coal mining, fire and explosion prevention, and neutralization and disposal of acid mine waters. It is the belief of coal technologists that when the emphasis shifts to coal as the primary source of energy. the existing methods of mining and preparation of coal must be improved considerably to supply large quantities of quality coal for energy conversion. It is the objective of the present large-scale research financed by ERDA to produce substitute fuels from coal. Large-scale gasification pilot plants are being constructed by Bituminous Coal Research, Consolidation Coal Co., Institute of Gas Technology, and the Pittsburgh Energy Research Center to produce coal gas of natural gas standards at 1,000 psig. The processes being adopted by these pilot plants are oriented towards recovering most of the sulfur from coal by absorbing H2S and its subsequent conversion to elemental sulfur. The environmental protection standards will be strictly followed in using the results of these pilot plants to construct large-scale coal gasification plants in the latter part of the 1970's. With the increasing awareness of the need for air pollution control, considerable research is being done to minimize sulfur dioxide emission from thermal power plants. Utilization of limestone and dolomite scrubbing systems and caustic treatment of stack gases have proved to reduce sulfur and nitric oxide emissions by about 90 to 96%.3 Currently, about 22 scrubbers are in use in the United States to reduce sulfur in stack gas emission. In the long-term, it appears that optimal combinations will be developed involving both advanced coal preparation technology and wet scrubbing. The sulfur compounds are converted either to elemental sulfur of sulfuric acid. Besides the sulfur compounds, the major byproduct of the coal utilization industry is the large amount of coal ash. The Coal Research Bureau at West Virginia University has developed a practical use for coal ash as a structural material. The coal industry will undergo revolutionary changes when coal becomes the primary source of energy. New coal mining and preparation processes will be introduced to meet the ever-increasing per capita energy requirements. 2. BENEFICATION Introduction Coal preparation, like the beneficiation of ores, is also aimed at the separation of values from associated waste. Even though the unit operations involved when enriching ores and coal are similar, there are certain characteristics unique to coal preparation. Unlike the scattered and concentrated veins of underground minera1 ores, coal is distributed uniformly and very much in abundance in the coal mines. Coal occurs as the metamorphosed sedimentary deposits of vegetable matter, while metal and mineral deposits occur in great varieties of forms, structures, and origin-from igneous to sedimentary and metamorphic. The mined coal, being much more friable than mineral ores, is subjected to less intensive size reduction operations. Ores are usually ground to a very fine size for subsequent concentration, while coal is crushed to a coarser size, since considerably less liberation is needed to achieve the desired degree of separation. Since mineral matter is to a great extent discretely distributed in coal, concentration is mainly achieved by taking advantage of differences in specific gravity between clean coal and associated waste. In general, about 90% of coal is concentrated using specific gravity separation and about 10% by froth flotation. In contrast, these operations are frequently reversed in the beneficiation of ores. In coal preparation almost all fractions separated during various stages are made use of. while large amounts of gangue material are rejected in the concentration of ores. Hence, coal generally has a much lower ratio of concentration than ores. Since ore deposits are frequently more variable and mineralogically complex than coal, beneficiation of ore may require more plant flexibility and point-to-point quality control. This characteristic difference between the mineral ores and coal is attributed to the generally used one-step processing in coal as compared to the multiple-step processing of ores. Dewatering to enhance the energy content of coal is usually considered a major unit operation. Even though thickening and filtration are common for dewatering ore concentrates and cleaned coal, vibrating centrifuges and disk filters find unique application in the coal industry for achieving these types of solid-fluid separation. In coal preparation, thermal drying is carried out in separate units at the mine. While ore concentrates are usually dried at the smelter. Although the drying of ores is seldom considered dangerous, volatile matter and combustible dust are reasons why the thermal drying of coal can be hazardous. Open air storage of ores and mined coal results in partial oxidation. Unlike the oxidation of ores, the oxidation of the pyritic and carbonaceous constituents of coal together with the heat of condensation of moisture contribute to spontaneous heating and the subsequent combustion of coal in storage. Among the other significant difference between concentration of ores and coal are the weight and capacity of processing equipment. Coal processing employs less cumbersome, higher capacity units while the beneficiation of ores usually requires much more massive and frequently lower capacity equipment. Properties of Coal Which Influence Design The widely varying and heterogeneous composition of coal, due to metamorphism, determines the preparation design and uses of the resulting products. Petrography serves as a useful system of classification to identify the coal types present and their distribution. Early

Jan 1, 1985

By Douglas W. Fuerstenau

This report presents the results of an investigation of comminution in tumbling mills. Five different topics involved with ball mill and rod mill grinding kinetics were studied and the results analyzed in terms of phenomenological size reduction and transport models. Continuous rod mill grinding was found to be characterized by high Peclet numbers which permit simulation to be carried out by several methods. The dry batch ball mill grinding of mineral mixtures showed that the breakage rates of the components were composition-dependent but time-independent and were normalizable with specific energy. Locked-cycle tests on mineral mixtures showed that a grinding circuit may take a long time to attain steady-state, during which time the composition of the mill holdings, and hence the breakage rates of the components, continuously changed. This study revealed that under plant conditions, grinding circuits can be in transience perpetually. The transport of mineral mixtures through drums was found to exhibit complex size and/or density-dependent segregation. However, the grinding media in a ball mill can eliminate such segregation, thereby simplifying the modeling of the continuous grinding of complex feeds. Wet batch rod mill grinding on single minerals divulged that the normalizability of breakage kinetics is valid for slurries of constant pulp density at different hold-ups but cannot be extended to slurries varying in pulp density.

Jan 1, 1983

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By Lztok Peruš, Goran Kugler, Matevz Fazarinc, Milan Tercel

"Hot deformability of M42 tool steel additionally alloyed with cobalt and molybdenum was investigated. Hot-compression tests were carried out in the temperature range 850 °C -1200 °C, at strain rates range 0.001--6s-l up to strain of0.9. Field-emission scanning electron microscope and optical microscopy were used for characterization of microstructure of deformed samples, which revealed a very complex precipitation of carbides that strongly depends on the soaking temperature, the soaking time, the stress state, the deformation temperature as well as on the strain rate. Gathered data was used to calculate the processing parameters such as process maps, apparent activation energies and strain hardening exponents. For better understanding of thermodynamical properties of the studied steel a simultaneous thermal analysis was conducted. Furthermore the analysis of phase equilibrium was calculated using Thermo-Cale software. On the basis of these studies the optimal soaking temperature and process windows were determined.IntroductionHot workability ofledeburitic tool steels is important economic factor. This means that for each tool steel individuallysafe range of hot working parameters should be revealed. Publications in the literature with regard to the hot workability of tool steels are rare and therefore more information from this research area is desired.The relatively low hot workability of ledeburitic tool steels, i.e. steels in which the solidification is completed by a eutectic transformation of the residual interdendritic liquid to austenite and various alloy carbides (ledeburitic carbides), is usually characterized by the production of surface and internal cracks during the hot deformation."

Jan 1, 2013

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By Derrick Chambers, George Kevin Chapin, M. Shawn Boltz

Seismic monitoring is one of the few noninvasive technologies with the potential to provide sub-surface geomechanical information to operators of large open-pit mines. Although passive seismic data has been used to refine emerging failure geometries and provide advance indication of surface deformations in the literature, doing so reliably in an operational context is much more difficult. This is due in part to difficulties in estimating and interpreting source locations and parameters in complex, low-stress open-pit environments. Additionally, the high costs associated with implementing, operating, and maintaining deep borehole seismic networks, which are most commonly used to monitor large open pits, can be difficult to justify, especially if monitoring benefits are not readily apparent. In this study, we explore the use of a near-surface nodal seismic deployment, which is commonly used in oil and gas exploration, for monitoring open-pit mining-related seismicity on a short-term basis. A deployment of 18 geophones was conducted on the surface in and around the Bingham Canyon Mine, a large open-pit mine near Salt Lake City, Utah, USA, where we find the small seismic array can detect and locate a variety of mining-related seismic sources, even with an extremely simplified velocity model. We outline the process of creating an idealized velocity model, developing a local magnitude scale, and interpreting the observed seismicity. Of note, we analyze a sequence of mining-induced events associated with a known structure on the south pit wall. We conclude with discussion on how surface-based deployments may be used to augment, or in some cases supplant, borehole seismic networks at large open-pit mines depending on monitoring requirements and objectives.

Apr 26, 2022

By H. C. Horwood

INTRODUCTION THE Argosy Gold Mines, Limited, which joined the ranks of active Ontario gold producers during the summer of 1936, holds a group of 21 claims on Casummit lake, in the Patricia portion, district of Kenora, northwestern Ontario. The Company is developing and mining goldbearing quartz veins that occur in a series of greywackes and slates of probable Keewatin age. The writer made a geological examination of the property and the surrounding area for the Ontario Department of Mines during the early part of the field season of 1936. This paper is a report on the general geology, structure, and ore deposits at the mine and is based almost entirely on data compiled during the examination. HISTORY Mineralization was first discovered on the property in May, 1929, by A. F. Hewitt, who, with J. A. Borthwick, decided that the country had prospecting possibilities and commenced work in April. Mr. Hewitt staked, and with his partner, J. Ziyone, still holds the group of claims lying immediately east of the present Argosy holdings. Mr. Borthwick staked six claims, K.R.L. 9,681 to 9,686, inclusive, adjoining Hewitt's on the west and later added claims K.R.L. 9,733 to 9,740, inclusive, to his holdings. F. Fiskness, who was also prospecting in the region, discoveted No. 1 vein on Borthwick's claims, and with his two partners, L. Parth and H. Jones, staked claims K.R.L. 9,758 to 9,763, inclusive, to the northwest of Borthwick's and Hewitt's ground. In July, 1929, the Casey Mountain Operating Syndicate, which held ground to the northwest, secured an option on Borthwick's claims. The Fiskness-Parth-Jones property was added in January, 1930, to protect the west dip of the veins. During the winter of 1930-31, the veins were explored by diamond drilling, No. 2 for a length ?of 900 feet and a vertical depth of from 51 to. 375 feet? and No. 3 .t~ a slope depth of 175 feet. I~ August, 1.931, after the msrallat10n of a miming plant, the Casey Summit Gold Mmes, limited, was incorporated to take over the property from the Syndicate. The Maple leaf Mines optioned a controlling interest in the stock in August, 1933, and on September 17th, 1934, brought a 50-ton amalgamation mill into production. From early in October to December 27th, 1934, when the mill was closed down, 4,094 tons of ore were treated to yield 887.89 ounces of gold and 87 .26 ounces of silver( ! ).

Jan 1, 1937

By Jasinder S. Jaspal

Most of the underground coal in the United States is mined via room-and-pillar mining methods with continuous miners. These machines operate intermittently because they have to wait for shuttle cars to interchange positions. To overcome this discontinuity in shuttle car haulage and to realize the full production potential of continuous miners, the U.S. Bureau of Mines developed a multiple-unit continuous haulage (MUCH) system through a research contract with Jeffrey Mining Machinery Div. (JMMD). The MUCH system consists of 12 rubber-tired vehicles and a bridge conveyor. The rubber-tired vehicles are connected by a unique mechanical linkage system to form a 250-ft train. The mechanical linkage permits the vehicles to track-retrack the preceding vehicle in both inby and outby directions. The cut coal cascades from one vehicle to another until it is discharged on the section conveyor belt. The MUCH system provides continuous haulage to the continuous miner. The MUCH system was initially surface tested by JMMD. Subsequent extensive testing was conducted by the Bureau at its test facilities at Bruceton, P A. Deficiencies found during testing were corrected. This report summarizes initial tests by JMMD and subsequent extensive tests and evaluation by the Bureau.

Jan 1, 1989

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013