Search Documents

By Andrew St. Amant

This report reviews the first three "investigative and concept generation" phases of the referenced contract, and details task performance of Phase IV. This last phase integrated the most promising concepts from Phases I, II, and III into a prototype detailed design which was manufactured, and then tested on a mine locomotive. The concepts developed during the first three phases provided "Improved Pole Tracking," automatic "Rapid Pole Retraction" in the event of dewirement, and servo-operated "Remote Pole Repositioning" on the trolley wire. The Appendix of this report supplies detailed information for the design and construction of the prototype system which is comprised of an RCB (Remotely Controlled Base subassembly), an RCL (Remote Control Lever subassembly) and an SAU (Servo Amplifier Unit) subassembly.

Jan 1, 1980

By Greg Canivan, Bernie Hertlein, Les Chernauskas, Joram Amir, Garland Likins, E. Anna Sellountou, Tim Kovacs, Peter Kandaris

Nondestructive testing of drilled shaft foundations via Crosshole Sonic Logging (CSL) is often performed as part of the quality assurance process to assess the soundness of concrete. The intent of CSL testing is to identify irregularities such as soil intrusion, necking, soft bottom, segregation, voids and other defects that could result in poor structural performance of the foundation. Over time, CSL rating criteria based on first arrival time and relative energy have incorrectly evolved to often be the sole means of determining the acceptability of a shaft. Some of these criteria have found their way into regulatory agency specifications, with acceptance values often differing from agency to agency.The purpose of this document is to review the state of the practice (including experience gained over the past 20 years), propose improved CSL rating criteria and make recommendations for additional assessment, as well as educate the industry on the proper interpretation of CSL test. CSL test results alone should not be the sole means of rejecting or accepting a shaft. A task force of industry exerts was formed to review the existing CSL rating criteria and propose improvements where appropriate. The recommendations presented herein are the consensus of the task force, which believes that they should be incorporated into future criteria, codes and specifications. This paper was produced as a joint effort between the Codes and Standards Committee, the Drilled Shafts Committee and Testing and Evaluation Committee. A task force was authorized under Testing and Evaluation Committee. The task force contributed their expertise in web-based discussions often every two weeks over a period of three years. Interested participants were invited to participate at any time. The document had two rounds of broad industry review, two rounds of DFI Technical Advisory Committee reviews, and a Public Comments process. All comments were considered in producing the final document.

Jan 1, 2019

By D. Harrington

This paper is a revision of Information Circular 7380, by D. Harrington and J. H. East, Jr., published in 1946, entitled ?Safe Storage, Handling, and Use of Commercial Explosives in Metal Mines, Nonmetallic Mines, and Quarries.? Issued soon after the close of World War II, this earlier circular described the unprecedented increase in the production and use of commercial explosives during the war as a result of expanded industry and the tremendous demand f or metals and minerals. In the years following World War II, the production and use of commercial explosives in the United States have continued to rise. Hence, the Bureau of Mines presents these revised figures through 1952. In rewriting this Wormation circular, most of the text prepared by Harrington and East has been retained, with newer statistical information compiled by Seth T. Reese, Accident Analysis Branch, and V. E. Wrenn, of the same branch.

Jan 1, 1954

By A. H. Anderson

THE travelling grate coking process was developed by Shawinigan Chemicals, Limited, at their Shawinigan Falls plant. The first production unit went into operation a month prior to the outbreak of the war. Since then a substantial part of the coke used in the manufacture of calcium carbide has been produced by this process. In the following will be given a short account of the development work, a description of the process and the equipment, a discussion of the properties of the coke, the economics of the process and its future possibilities. EXPERIMENTAL WORK The carbide industry is a large consumer of coke, one ton of commercial carbide requiring for its production 1,200 lb. This coke must meet certain specifications in order to be acceptable. It should have a low ash content, preferably below 8 per cent, and the sulphur and phosphorus content must not be above specified limits. The size of the coke is also important. If it is too large it has to be crushed before it can be used in the furnaces, and if it is too fine it may have to be screened and briquetted. In addition, it must be dry. Although it was generally possible to purchase coke, including petroleum coke, and coke fines, in the quantities required, it became increasingly more difficult as time went on to obtain coke of a suitable quality at an attractive price. It was therefore natural for us to look to coal carbonization as a means of basing the supply of the fundamental raw material for carbide manufacture on something more solid than the shifting conditions of the coke market.

Jan 1, 1944

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By Jr. Schnakenberg

In 1986 the U. S. Bureau of Mines (USBM) embarked on a major research effort to develop technology that can substantially reduce worker exposure to face hazards simply by relocating the equipment operators to an area of relative safety. This reduced exposure mining system (REMS) research effort enhances the USBM ongoing health and safety research efforts to reduce and control dust and noise and to reduce accidents through training and better mining practices. This paper reports progress of the research that is developing and will demonstrate the technologies required for the computer-assisted tele-remote operation of continuous mining machines, haulage systems, and roof bolting machines.

Jan 1, 1996

By R. Burns, A. I. A. Salama, M. W. Mikhail

"Large amounts of oil sand tailings are produced in the Fort McMurray area, including sand, clays, and misplaced bitumen. The objective of the present study (as part of the overall engineered tailings program) is to select and evaluate the role of hydrocyclones in removing most of the solids from the tailings slurry and producing an underflow product containing about 75% solids.Multistage cyclones were evaluated in pilot plant tests. Slurry feeds with different percents solids and increasing ratios of superfines (–44 µm) were used in testing multistage cyclone circuits. A two-stage Linatex separator circuit gave high recovery to the underflow of 98.8% to 99.6% by mass with the desired high solids content in the underflow of 73% to 75% by mass. Changes in feed solids content (20% to 50%) had little or no influence on cyclone underflow recovery and solids content. The keys to achieving such results were the apex control mechanism and operation at relatively low feed pressure (<60 kPa for 23 cm F cyclone) when the feed solids content was high. Increasing superfines above 7% by mass in the feed resulted in a significant reduction in the recovery to the underflow, probably due to the heavy medium generated by excessive amounts of clays in the cyclone. Pilot plant results were better than those predicted by available cyclone simulation models in terms of recovery and solids concentration in the underflow.Increasing cyclone diameter from 23 cm for the Linatex separator to 51 cm for the Krebs cyclone appears to have little or no effect on size cutpoint."

Jan 1, 1997

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author&apos;s experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author&apos;s experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet&apos;s manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet&apos;s specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

By John C. Leighton, C. O. Brawner, Doug Stewart

"Despite the availability of established, sophisticated methods for planning and designing stable slopes in rock, comparatively little attention is usually paid to the problems of carrying out the excavation. Blasting should be carefully planned to obtain optimum fragmentation as well as steep, stable working and final pit walls. The principal difficulty facing a blast designer is the lack of prior information about the many critical blasting characteristics of the rock mass. The common practise of trial-and-error lasting will eventually lead to a suitable program, but must be repeated time after time in variable geology. This frequently results in many blast-damaged slopes. Recent research indicates that monitoring drill performance will yield a Rock Quality Index which correlates to a Powder Factor value. The drilling can provide a continual supply of data, reflecting changes in the rock mass which enables the selection of an economical powder factor.IntroductionWhen planning to excavate a large-scale rock slope, engineer s will generally spend considerable effort to produce a safe, feasible and economical design. Much time will usually be spent on the field map ping, &apos;structural geologic studies, surface and subsurface hydrology, determination of strengths and effective friction angles of discontinuities, and finally checking stability with the aid of mathematical and analytical models. If the rock cut is to be along a transportation corridor, the prime justification for this time and effort is to produce a clean, stable slope which will be safe for those travelling or working beneath it. For the walls of an open-pit mine, there is the additional economic incentive to maintain the steepest stable slope angle for the minimum stripping ratio (Stewart and Kennedy)."

Jan 1, 1982

By William H. Emmons

Jan 1, 1912

By F F. Pitard

The optimization of metallurgical processes requires knowledge of the heterogeneity carried by constituents of interest. The common scenario, almost an industry standard, is to rely on the engineering firm who in turn relies on favorite manufacturers of sampling equipment to provide the appropriate sampling systems in the plant to perform accurate metallurgical accounting. This sequence is flawed from the beginning to the end because everything should be based on a careful understanding of the Theory of Sampling (TOS) by the company project team and their expert who invariably would suggest various approaches and different sampling systems.The necessary progressive and iterative approach should be that the company’s project team (mining or other industries) would do its home work to have a good understanding of the geometallurgy, mineralogy and texture of the ore in each geological unit so consultants and engineers would have the best information to start with. Then a reputable sampling expert would recommend which sampling systems are needed, so the company would require engineering firms to follow pre-established, non-negotiable requirements, and finally select the sampling equipment existing on the market today that is most likely to lead to accurate and precise enough metallurgical accounting.It is the author’s experience that when this necessary progressive and iterative approach is bypassed, sampling systems installed in the plant are likely to transgress the most elementary rules of sampling correctness. Invariably the argument is that the company cannot afford correct sampling systems for metallurgical accounting as suggested in the Theory of Sampling. There is nothing that is farther from the truth when later problems will develop and inevitable reconciliation difficulties with miners and geologists become daily routine with impossible answers; as a last resource the sampling expert may be called to perform a post-mortem analysis.The progressive and iterative approach suggested in this paper should be a due diligence requirement for any bank providing a loan for an important new mining project; anything less is most likely to generate unpleasant financial losses; historical, well-known examples are referred to.CITATION:Pitard, F F, 2015. A progressive, iterative approach leading to reliable metallurgical accounting sampling systems, in Proceedings MetPlant 2015, pp 78–91 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Junmo Ahn

This study investigated leaching kinetics by alternative lixiviants for copper leaching from chalcopyrite (CuFeS2), the most abundant copper resource in the world. As a refractory sulfide mineral, chalcopyrite shows low copper extraction due to passivation on chalcopyrite surface. Also, decrease of copper grade with high portion chalcopyrite requires the alternative leaching procedure to increase copper recovery. Therefore, alternative lixiviants such as sulfurous acid and methanesulfonic acid (MSA) were tested for both concentrate and low grade ore to enhance copper extraction. Also, an oxidant, hydrogen peroxide, was compared to ferric to find out the improvement of leaching kinetic. In concentrate leaching tests, 30 g/L MSA showed the highest copper extraction (47%), compared to other lixiviants at 75 °C. Periodical H2O2 addition enhanced copper extraction, and above 90% of copper extraction was observed within 96 h by periodical addition of 0.6% H2O2 at 75 °C. The activation energy of chalcopyrite leaching by MSA and H2O2 achieved 40 kJ/mol, which is chemical reaction control. The results of low grade ore leaching tests indicates that no significant difference among lixiviants (H2SO4, H2SO3 and MSA) with ferric was observed, all of which achieved around 37% within 24 h at room temperature. However, significant increase of copper extraction (>80%) was observed at both 20 g/L MSA and 10 g/L H2SO4 conditions by the addition of 10% H2O2.

By Mark Liskowich

When is it the proper time to initiate engagement with various stakeholders, including Indigenous communities? This paper will demonstrate what stage of a project’s evolution is the appropriate time to initiate a stakeholder engagement plan. It will look at aspects to consider when identifying the communities to involve. It will describe the contents of a Stakeholder Engagement Management Plan as well and touch on how tried and true options analyses, such as a Multiple Accounts Analysis can be used to inform the results of the engagement, guide the development of your project and clearly document the engagement process. It will illustrate the benefits of initiating engagement at the appropriate point in your project’s schedule, and the limitations of doing so too early and at later stages of the project engineering. The benefits of this approach can be realized within any legislative Jurisdiction including the Canadian Environmental Assessment Act 2012 and Canada’s new Impact Assessment Act.

Jan 1, 2020

By A Tolley

Bauxite residue or ‘red mud’ is a by-product of the Bayer Process, the primary process of alumina refining. Due to its high alkalinity and variable composition, its storage and disposal poses high environmental risks to water sources, surrounding ecosystems and human health. The high alkalinity (pH 12–13) is a significant factor in its classification as hazardous waste; to mitigate this, Australian refineries have integrated neutralisation processes into bauxite refining. Both sea water and carbon dioxide neutralisation processes are applicable. Multiple studies have demonstrated pH reduction from 12–13 to 7–10, depending on the method. The key advantages of CO2 neutralisation are that it allows for carbon sequestration and is more effective when utilised as a pre-treatment for recovery of metals, while sea water neutralisation is more established and has been integrated into two Australian refineries. This paper proposes the application of the bacteria Exiguobacterium oxidotolerans for bioleaching of iron from hematite in bauxite residue. The genus Exiguobacterium is characterised by its high levels of adaptability, halotolerance and alkaliphilic nature. E. oxidotolerans is successful at eluting Fe2+ from hematite via reductive dissolution, which complexes with oxalic acid produced during metabolism. This aquatic bacterium presents a novel process pathway for iron elution due to direct interaction of E. oxidotolerans with hematite via the cell membrane and operates within the pH range of neutralised red mud. The proposed mechanism is extracellular electron transfer, a microbial metabolic process where electron transfer is facilitated between bacterial cells and extracellular material. Currently this is being investigated for promotion of seaweed growth in coastal environments as soluble iron aids and fortifies colonies. This has potential downstream applications for cleaner iron and steel production. While theoretical, this paper explores the neutralisation, bioleaching and application of the Fe(II)- and Fe(III)-oxalate complexes formed.

Sep 18, 2023

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

The purpose of this paper is to demonstrate how the Computational Fluid Dynamics (CFD) technique can be an attractive approach to evaluate the performance of face ventilation systems. To present the capability of the CFD for such a study and for design purposes, a series of simulations using CFD have been performed at the Department of Mining Engineering, University of Kentucky, for different face ventilation arrangements (e.g. different scrubber geometries, brattice (curtain) and continuous miners locations, airflow quantities, etc.). Results from these simulations are displayed as three dimensional graphs and discussed. Needs for the field validation of these results and refinements of design methodologies are also discussed.

Jan 1, 1998