Search Documents

By P. C. Benedict, J. A. Titcomb

"The following description of the geology of the Northern Empire mine is recorded by the senior author, but is based on the observations and complementary mapping of both authors.The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, Thunder Bay district, Ontario.Production started in March, 1934, and terminated in September, 1941. The total number of tons milled was 425,866, from which 153,103 oz. gold was recovered. The lowest level from which ore was mined was the 1,900- foot, but considerable drifting was performed on the 2,075-foot and 800 feet on the 2,415-foot, the deepest level,The vein strikes about N.72°E. and has an average dip of80°S. In stoped sections the quartz averaged about 2 feet wide. On the 1,725-foot level it was drifted on continuously for more than 7,000 feet. In the mine as a whole, practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section, but not much beyond these limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth .The vein is in 'Keewatin' lava flows, to which it is almost conformable. It lies only a short distance south from the 'Timiskaming-Keewatin' contact ( Fig. 2). This contact is marked by a black graphitic fault. So far as is known the fault is parallel, or nearly parallel, with the flows in strike, but dips at 72°S., which is 5° flatter than the average dip of the overturned flows. A post-vein, almost flat sheet of diabase about 550 feet thick cuts outthe vein from about the 650- to the 1,200-foot level ( Figs . 1 and 3). If it was intruded along a fault, the fault had only minor displacement. A strong alteration halo extends to 200 feet above and below the diabase. The vein was conspicuous but in large part it was below ore grade for 100 feet or more above and below the diabase.-"

Jan 1, 1954

By Steve Karl, Rock Jenkins

The mining industry appears to be slowly rebounding. But many individuals and company officials are still smarting from the beating they received during the recent recession. As a result, companies have taken the "lean and mean" approach. As pointed out at the Oct. 24-26, 1984 SME-AIME Fall Meeting in Denver, CO, companies are placing more emphasis on optimizing their operations through more efficient mining and processing technologies and equipment. Empathizing with the mining industry's woes was the meeting's welcoming luncheon speaker, John D. Withrow, Jr., executive vice president product development for Chrysler Corp. Withrow paralleled Chrysler's problems of a few years ago with the current problems facing the US mining industry. He said Chrysler's come-back centered around its engineering and technical personnel, who regained "their seat at the head table." "In short," Withrow said, "we had lost the competitive edge. By cutting costs and people and improving our products we got everybody to believe we could." The 2700 participants at the Fall Meeting attended technical sessions geared toward turning mining back into a productive and profitable industry. Sessions and symposia included papers on precious metals extraction, crushing and grinding innovations, geomechanics, environmental control, health and safety, and various commodities. This article briefly highlights some of the papers presented. To order preprints of these technical papers, see ME, December 1984, pages 1620 and 1621. Computers Gain Mining Acceptance High tech has reached mining. As evidenced by many papers, computers have become valuable tools in many applications. These include tailings ponds operation and waste management; truck dispatching; mine design, simulation, and scheduling; monitoring; and reclamation. Mine planning is generally labor intensive and requires a considerable amount of the planner's time. P. K. Chatterjee, X. Chung, and Y. Jianjy described a computer-generated interactive graphics approach to under-ground coal mine planning that lessens the manhours involved in producing plans. The computer program examined exploratory borehole information. This included coal seam thickness, tonnage, quality constraints, and the nature of their distribution. Layout designs were then initiated and a probabilistic simulation performed to determine production levels of different extraction strategies. The interactive graphics approach gives planners the ability to quickly evaluate several layout alternatives and select the best one. For surface coal mines, M. A. White, of Arch Minerals Corp., explained several computer programs that aided in his company's surface mine plans. Several drill hole database and modeling pack¬ages are available. But Arch tech¬nicians developed specific pro¬grams for model strip areas. They were used to form long-term pro¬jections for various area and semi¬area stripping operations. They also generated reports on yard¬age, tonnage, quality, and ratio in¬formation. The information is used in budgeting, to compare mine plans, and to analyze acqui¬sition candidates. While computer-based truck dispatching systems have been used in mining for some time, earlier systems were run on ex¬pensive mainframe or high per¬formance minicomputers. As such, computer-based truck dis¬patching systems have been too expensive for all but the largest mines. Recently, however, a microcomputer-based system, af¬fordable to smaller mine opera¬tors, has become technologically feasible. Y. C. Kim and W. E. Kolb re¬ported on a simulated microcom¬puter system that uses strategi¬cally placed signposts in the pit area to automatically detect truck movements. A microprocessor in the signpost sends information to the microcomputer. The computer determines the truck's assign¬ment and alerts the dispatcher. He radios the driver his assign¬ment. In addition to the technical pa¬pers, an introductory short course on microcomputers was offered at the meeting. L. M. Kass and J. P. Stone, from the US Bureau of Mines, walked participants through the uses of microcom-

Jan 1, 1985

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Komatsu is helping to bring mining performance and analytics to the next level.By evaluating underground haulage, a significant component of the room and pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Komatsu is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way.These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer nice to haves, they are must haves.Starting with the best products and the right people is a first step, but then what? How do mines take their operations from average to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way.The fundamentals of operational excellence (OpEx) are based upon the process of define, measure, analyze, improve and control (DMAIC). DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes and then improving the performance and controlling the operation.Komatsu uses OpEx or lean principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety.These same principles can be applied in most situations to streamline processes, improve operations and deliver value."

Jan 12, 2017

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By L. B. Phelps

Current mining regulations require revegetation in reclaiming surface nines. Excessive soil compaction can be an impediment to successful revegetation in poor soil conditions common to Eastern coal nine sites. A field study was performed to determine the bulk densities of soils that had been spread by either bulldozers or scrapers at a strip nine site. Moisture-density relationships for the soils were determined from the field samples. These were compared with stockpile samples compacted by the Standard Proctor compaction test. The results of the study indicate that the degree of compaction could be lessened through proper soil handling procedures.

Jan 1, 1986

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By Jerry J. Gray

Transportation charges for mineral commodity movements in western Oregon and western Washington were determined mainly by a stratified random sample canvass of producers. Total 1965 mineral production value for this area was $53.3 million; the cost or charge to move this production from the mine to the consumer or to the point of consumption was determined to be an additional $38.7 million. Thirty seven companies were contacted as a sample out of a total population of 349; the statistically expanded sample production value deviated 3.6 percent from that obtained by the Bureau's annual canvass. The agreement between the sample results and the canvass totals demonstrated the effectiveness of the sampling method for obtaining data with a predesigned level of accuracy. For comparison, the north-central Idaho and western Montana area was studied, A random sample experiment was designed, but because of the dominance of a few major companies, a random sample technique would have required more visits to producers than if only the larger firms were contacted. Eighty-four percent of the 1966 mineral value ($198.6 million) was accounted for by interviewing 27 firms out of a total population of 199. Total transportation costs or charges for the area were $26.7 million. The significant difference observed between the relationship of minerals production value and transport charges between the two areas investigated can be attributed to the difference in the minerals produced. The western Oregon and western Washington region is a nonmetals-producing area as opposed to the predominance of metals production in the Idaho-Montana region.

Jan 1, 1968

By A. C. Fieldner

It is estimated that 6,202,235,000 gallons .of- gasoline was produced during the year 1922. The crude light oil- output Burin- the same year is estimated at 111,000,000 gallons, or 1.8 per cent of the gasoline production. In fact, if all the coal mined were coked in by-product ovens, and the light oil recovered therefrom, this product would amount to only 15 to 20 per cent of the quantity of the petroleum gasoline now produced annually. It is obvious therefore, from these figures that the light oils by present coking processes can not assume great importance as a gasoline substitute in a national sense. However, the use of light oil as a motor fuel is of real importance in districts adjacent to by-product coking operations from which a reasonable proportion of the local motor fuel supply may be derived. The certainty of diminution of petroleum resources in the relatively near future demands the utmost utilization of gasoline substitutes from the distillation of coal as well as other sources. Motor benzol is a by-product from the destructive distillation of coal. From 11/2 to 3 gallons of refined motor benzol is obtained per ton of coal carbonized. The light oil vapors are extracted from the by-product coke-oven gas by passing it upward through a series of towers in which these vapors are absorbed in a descending current of "wash" oil (petroleum distillate). The light, oil is recovered from this wash oil by distillation with live steam, the resulting crude light oil consisting of a mixture of benzol, toluol, xylol, solvent naphtha, and a small amount of other substances (unsaturated hydro-carbons, carbon disulphide, and other sulphur compounds, phenols and pyridines) is then transferred to an intermittent still and fractionated into crude motor benzol, which includes the toluol and a part of the xylol or light solvent naphtha. The crude, motor benzol is yellow in color, contains sulphur compounds which corrode copper and brass, and also contains unsaturated bodies which oxidize and polymerize on standing, producing sediment and forming gummy deposits highly objectionable when the benzol is used in motors. These objectionable

Jan 1, 1923

By John R. Coulson

Each State and the Federal Government was surveyed for existing certification requirements, the industry yes surveyed for the needs for training blasters, and the training that was available. Recommendations for training and certification for blasters were made.

Jan 1, 1980

By B. M. Harra, O&apos

Zinc smelting is frequently termed a backward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, low-unit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pounds of ore. The diameter of the retort is limited by the time required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, or producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser attached to one end of the retort, where it condenses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls and of the ore charge itself, the heat efficiency even of the most modern regenerative furnaces is only about 12 per cent. The retorts have a short life, 30 to 60 days, at the high temperature required; zinc

Jan 1, 1923

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to all aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, and Treasury, and the Central Intelligence Agency, whose primary mission is the collection of data in non mineral subject areas, but in which the mineral industry is a component.

Jan 1, 1982

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By P. Danson, D. A. White, S. Bashir

Composite ion exchange materials made of SnO2, TiO2 and MnO2 can be used to remove radioactive contaminants from nuclear waste streams. In several cases their selectivity and capacity are enhanced by mixing hydrous silica into the matrix. MnO2-SiO2 materials are especially useful for a number of reasons, such as their selection of heavy elements over caesium. Distribution constants and determinations of exchange capacities show that in many instances the properties of the composites are better than those of the oxides alone, while the presence of a chelating agent has been found to reduce the uptake of nuclides considerably. Methods are being developed for the bulk manufacture of the materials. Further work on sorption mechanisms is required to explain anomalous results, particularly the variation in exchange capacity for different elements and the ability of the oxides to sorb colloidal material in alkaline solution.

Jan 8, 1992

By G. Bourque

One of the design criteria for the Mount Wright facilities was to incorporate the latest proven automation techniques and devices for the new crushing, grinding and concentrating plant. The heart of the centralized control system is a Fox 1 process computer, located in the central control room in the administration building. The entire operation, i.e. crushing, conveying, storing, grinding and concentrating, is monitored and controlled, through the process computer , by one operator via a CRT console. In case of computer failure, the control is automatically, and without process interruption, transferred to manual back-up panels. One of the newest management tools, the process computer is programmed to collect and automatically print out shift. daily and monthly reports on tonnage, metallurgy and equipment operating time, for better planning of operations and preventative maintenance.

Jan 1, 1977

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

By Q. X. Yun

This paper provides a new approach to optimize the production planning in underground mines by means of evolutionary algorithms. Firstly, genetic algorithm is used to reach the global optimization in planning. Then, evolutionary programming is employed to obtain the partial optimization for each year. The application proves that the new approach is reasonable and useful. Keywords: Evolutionary algorithm, Genetic algorithm, Evolutionary programming, Optimization, Mining engineering.

Jan 1, 2003

The revised estimate of coal production in January 1977, is 39 million tons -- down 12 mi 11 ion tons compared with production in January of last year, largely as a consequence of the snow storms and cold. The major coal-hauling railroads operating in Eastern and Midwestern States reported to the Bureau of Mines that they loaded approximately the same number of cars for the week ended February 5, as in the preceding week. The Bureau of Mines estimates that U.S. coal production for the week ending February 5, 1977, was approximately 8.5 million tons, or nearly 3.5 million tons less than production for the corresponding week in 1976. Coal production from January 1 - February 5, 1977, was approximately 47.8 mi 11 ion tons compared with production of 63.5 million tons for the corresponding period in 1976. As of the first week in February, river and truck shipments of coal in the Eastern U.S. were about one-half of the normal traffic. Despite the freezing weather and ice and snow conditions of rivers and highways and reduced rail shipments, there was reportedly little or no shortage in coal supply to consumers. Inventories at electric utility plants and steel company coke plants at the beginning of the severe weather were sufficient in most cases for at least 30 days" operations. There have been no reports of coal shortages at other industrial plants.

Jan 1, 1977

By JIACHENG XIE, XUEWEN WANG, QINGBAO BAO, ZEWEN YAN

The general application of memory cutting technology to shearers is improving the intelligence of the working face, but it has its limitations. It is only suitable for conditions where the environment of coal seam is changing slowly. It compensates for the cutting height by changing the fuselage attitude, and frequently adjusts the height to control the learning cutting trajectory, but due to the problems of shearer control and height adjustment accuracy, it cannot adapt to and compensate for the change of cutting height in a timely manner, resulting in poor cutting accuracy. This study puts forward a virtual memory cutting method based on prediction of the shape of the armored face conveyor (AFC). The integrated key technologies include generation of virtual teaching cutting curve, height adjustment strategy of front and rear drums, cutting

This paper will review some of the work conducted in the past at the Dynamic Effects Laboratory to examine the use of stress waves and fracture mechanics in understanding dynamic fracture and fragmentation in blasting applications. Along the way, we will use photoelasticity and high speed photography to better understand the mechanisms of fracture and fragmentation.

Jan 1, 2015