Search Documents

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

In Broken Hill, Northern Rhodesia, two water jacket lead furnaces have been in operation for the past three years. The furnaces were erected in war time, and only absolute essentials were procurable. The water for the jackets was obtained from wells adjacent to the works, in a dolomite formation. There being no water-softening plant, except a small one capable of treating water for the power plant only, this water was found to make a heavy scale in the jacket. During 1917 several jackets were burnt through, resulting in serious trouble and loss of output. In order to avoid this, furnaces were stopped twice a month for 8 hours and scale was removed as far as possible. In addition to the scale trouble during the summer months, a green slime grew in the supply tanks and occasionally became detached from the tank and collected in the cocks near the jackets. This caused risk to the jackets and was difficult to remove without a stoppage of the furnace. In 1918, bundles of wattle bark were placed in the hot well at the rate of one ton per month. These extracted the tannin and added from 0.5 to one part of tannin per 100,000 to the circulating water. The hot water was cooled over a brushwood cooling tower and returned to the supply tanks. The well water required to, make up the wastage was estimated at 40,000 gal per day.

Jan 1, 1920

By Khaled Morsy

The tragic incidents at Sago and Darby coal mines in 2006 pointed out the need for stronger seals to resist the blast effects of violent gob explosions. Mine Safety and Health Administration (MSHA) has published the final rule on Sealing of Abandoned Areas in April 2008. According to the final rule, the mine seals for unmonitored gob areas should withstand an instantaneous pressure of 120 psi. Reinforced concrete (RC) seal is one of the feasible options that can be used to meet the final rule. Concrete is a heterogeneous, cohesive-frictional material and exhibits complex non-linear inelastic behavior under multi-axial state of stress. The increased use of concrete as primary structural material requires the development of sophisticated material models to have an accurate prediction of the material response to a variety of loading situations. The constitutive modeling of concrete has advanced considerably in the past three decades. Choosing a reasonable concrete material model is important in order to obtain an accurate mine seal design. This paper attempts to address the effect of different concrete material models on the response of RC seal subjected to dynamic loads from methane explosion. Three concrete models, from ABAQUS library, were selected to address the effect of non-linear behavior of concrete and damages due to tensile and compressive stresses. In addition, a typical and verified concrete material model was used for conducting 3D finite element models simulating the RC seal by ABAQUS, EXPLICIT ver. 6.6.

Jan 1, 2008

By D. Xie, S. Sun

An overview of recent development of CSIRO?s Multi-Phase reaction models will be presented with examples comparing the calculated physico-chemical properties of metallurgical slags with the existing experimental data. The paper will also outline the development of a kinetically based model for molten bath reactors and its application to submerged combustion of coal in a slag bath as well as the reaction between the slag and injected coal particles. The plume model combines established models for the combustion of pulverized fuel with models for the growth and rise of bubbles from a lance or tuyere. This model predicts the extent of de-volatilization and combustion of the coal in the plume, the utilization of oxygen and the exchange rate of oxygen between the gas and the bath as well as the heat transfer rate between the gas bubbles and the bath. The slag reduction model brings together the recently measured rate data and fundamental understanding of the kinetics of CO-CO2reaction with iron oxide containing slags and predicts the changes resulting from injection of coal particles into molten slags. The top-space model covers reactions between gases and molten droplets in the post-combustion zone, where heat and mass transfer between phases results in higher utilization of the fuel values in the partly oxidized gases and transfer of heat to the molten bath. Keywords: Phase equilibria, viscosity, electrical conductivity, slags, kinetics, reaction rate.

Jan 1, 2004

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By Sachihiko Tokunaga, Hirofumi Taguchi, Kenji Maruyama, Hidenori Takahashi, Yoshiyuki Morikawa

"Abstract The present study proposed a new liquefaction countermeasure to improve sandy ground and conducted a trial execution. The new method is a floating-type and lattice-shaped cement treatment method, where cement-treated soil is not fixed to a non-liquefiable stratum. A fixed structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were first conducted to confirm the mechanism of the new method. Then, a series of centrifuge model tests were performed to demonstrate the effect under a stress condition at the prototype scale. The analyses and model tests confirmed the effect of the liquefaction countermeasure. Finally, trial executions were carried out to confirm high-quality vertical execution.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. In particular, the cost of the high-pressure jet mixing method, which can be applied to the liquefiable ground under existing structures, is significantly high. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2014

By B. S. Xakalashe

Keywords: Pyrometallurgy, silicon, solar cells Silicon has been the dominant material in the photovoltaic (PV) industry since its application in the space industry in 1958. This review focuses on crystalline silicon solar cells, primarily due to their dominance in the photovoltaic industry, omitting other photovoltaic cell technologies such as second generation (e.g. thin films) and third generation (e.g. nano-structured solar cells). The value chain for the production of crystalline silicon solar cells has been reviewed. The primary processing steps for the production of silicon solar cells from quartz are as follows: bulk production of metallurgical-grade silicon via carbothermic reduction in a submerged furnace, refining of metallurgical-grade silicon via the chemical means to polycrystalline silicon, or through the metallurgical route to solar-grade silicon, wafer manufacturing, and, lastly, silicon solar cell manufacturing. During downstream processing, solar cells are interconnected and encapsulated into solar modules (panels), which can be used individually or incorporated into a photovoltaic system for electricity generation and supply. The cost for crystalline silicon based solar cells is approaching one US dollar per watt peak ($1/Wp), while the most cost-effective solar modules in industry have reported costs below $1/Wp, and are based on CdTe thin films. Solar cell energy conversion efficiencies as high as 22% have been reported in industry for crystalline silicon solar cells.

Jan 1, 2011

By John C. Tosh, Peter M. Kandaris, Sheldon John

Geologic, geotechnical and hydrologic studies were performed for the design of 115 deep, large diameter drilled shaft reinforced concrete foundations (6 to 12 feet) to support tall steel monopoles for a new 13-mile long 230/69kV transmission line in southwestern Arizona. The subsurface conditions along the alignment posed a wide range of challenges for performing investigation and design studies. These conditions include saturated, loose granular flood plain deposits with generally low lateral capacity, potential ground loss up to 23 feet due to occasional river flow (scour and embankment loss), liquefaction impacts from nearby active fault seismicity that can generate magnitude 6.5-7.0 earthquakes, and unsaturated alluvial and eolian sand-dominated soils to full depth with low lateral capacity. All conditions will require significantly deeper than normal foundation embedment (depth ranging from 22 to 77 feet) and will present construction difficulty due to ground instability from groundwater and dry soil sloughing. A phased investigation was performed to accurately characterize the conditions for design and construction, and included performing a review of existing data, detailed field geologic reconnaissance, a limited number of standard exploratory borings (limited access), seismic cone penetrometer soundings (SCPT) in saturated soils to better understand liquefaction and strength loss potential, and hydrologic analyses to estimate scour/ground loss potential. This paper describes the site conditions, presents details on the investigation team’s approach, documents findings in relation to deep foundation analysis and design, and discusses recommendations for foundation construction to help in reducing risk.

Sep 8, 2021

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By Charles S. Barrett

NUMEROUS determinations1-7 of the tex-ture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Wever1 and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the roll-ing direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist.

Jan 1, 1940

The paper deals with the results of dynamic tests carried out on a range of surface support liners consisting of combinations of mesh (various types), shotcrete, and wire rope lacing. The testing was carried out over the period 1993 to 1998. The dynamic testing method made use of drop weight impact loading of test samples which attempted to simulate realistic in situ conditions, and the range of loading imposed was equivalent to small to severe rockburst conditions. The results of the testing provide quantitative data, in the form of input energy, which is relevant for support design and for the choice of support types appropriate for situations in which significant mine-induced seismicity occurs or is expected to occur. In addition to the wire mesh and shotcrete liner systems tested, estimates of energy capacity are made for other, untested, systems.

Jan 1, 2001

By Hennessy F. L

It is generally recognised that slags are active participants in pyrometallurgical processes, and not merely inert liquids which must be produced. to effect separation of gangue material in smelting, or of impurities in refining. The importance attached to slag-metal reactions in steelmaking is shown by the numerous investigations in this field. However, there are still many important reactions of slags which require explanation. In this paper some new aspects of the reactions of slags will be discussed, as far as possible quantitatively.FREE AND COMBINED OXIDESMetallurgical experience indicates that variations in the composition of slags produce changes in the chemical behaviour of the various components. These variations have been generally ascribed to changes in the proportions of free and combined oxides, i.e., compounds have been assumed to be present in the liquid slag.Considerable support for this view has been adduced from the existence of compounds such as metallic silicates, phosphates, etc., in the solIdified slag. However, this does not imply that such compounds necessarily exist in the molten slag.The most direct evidence as to the nature of molten slag is to be obtained from a study of the liquid state. In...

Jan 1, 1950

By P Toor

Mill filling is an important operational parameter in a SAG mill circuit and by its control and optimisation it can produce significant improvements in production capacity and energy efficiency. However, it is industry practice to report mill load as the total output given by load cells, or kPa for systems based on lubrication bearing back pressure, rather than the actual percent total mill filling.Ball trajectory is another critical parameter as overthrow can result in accelerated liner wear and possibly liner failure whilst underthrow can result in reduced grinding action. The assessment of ball trajectory cannot be done in isolation as the toe of the charge needs to be determined to make any meaningful assessment. Thus both total percent mill filling and mill trajectory are critical parameters; however neither is reported or available to metallurgy or processing teams in real time or a regular basis.In this study the performance of a fixed speed SAG mill was assessed and optimised by employing mill trajectory models and using the JKMRC power model to calculate percent total mill filling. Power Curves, which correlate ball filling, mill filling and mill power, were also developed. The Power Curves, with additional knowledge from the trajectory models allowed for the identification of optimal operating regions for the mill.CITATION:Toor, P, 2015. Optimisation of a semi-autogenous grinding mill through trajectory and power modelling, in Proceedings MetPlant 2015, pp 142–149 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By P Moswate, D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of gangue mineral grade limits by the concentrator may also result in significant penalties.Online grade analysers which can provide reliable real time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and has the benefit of operating in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades.MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at the BCL nickel concentrator plant in Botswana. The project focused on stabilising the final concentrate grade while ensuring the final tailings are minimised, resulting in an improved nickel recovery. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser. The positive results show the advantages of combining reliable real time measurements with an advanced process control system.CITATION:Mantsho, S M, Moswate, P, Strobos, P and Phillpotts, D, 2013. The implementation of floatstar grade-recovery optimisation control solutions using Blue Cube Online grade analysers on industrial flotation circuits, in Proceedings MetPlant 2013 , pp 575-582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D G. Randall, R Jivanji, J Nathoo, T Reddy

Paradoxically, the increased emphasis on water treatment in mining has generated a new problem û hypersaline brines. Currently brines are either disposed of into ash systems, lined evaporation ponds or hazardous waste sites. Evaporative crystallisation (EC) is an alternative, but the energy requirements can be prohibitive and the salt product is still a waste that must be disposed of. Eutectic freeze crystallisation (EFC) is an alternative technology that is capable of separating aqueous solutions into pure water (as ice) and pure, solidified solutes. It is highly energy efficient and does not depend on the introduction of any solvents. In addition, the simultaneous production of pure ice and potentially saleable pure salt(s) is a major advantage. Although EFC has been shown to be effective in separating a single salt and water, it is still in the early stages of being applied to the multi-component hypersaline brines that are typical of reverse osmosis retentates generated by mining and extractive metallurgy.This paper presents an EFC brine treatment protocol developed by the Crystallisation and Precipitation Unit at the University of Cape Town. The protocol incorporates brine analysis, thermodynamic modelling to establish which salts will freeze out and at which temperatures, followed by experimental studies to determine the kinetic parameters, such as nucleation temperatures, salt yields and crystal purity.Case studies showing the application of EFC for the purification of typical brines containing high levels of sodium, chlorine, sulfate and ammonia (Brine 1) and a mixture of sodium and magnesium sulfate (Brine 2) are covered. Modelling tools were applied to describe the phase behaviour of the multi-component saline systems under different process conditions. Experimental validation was carried out using synthetic brines of different (and increasingly complex) compositions. The results showed that EFC could be used to selectively recover the sodium as a sodium sulfate salt from both different brines. The simulation tools were useful in the analysis and understanding of the process.A preliminary economic analysis showed that the operating costs for EC were approximately nine times those for EFC, but the capital costs were much less- equipment for EC cost about half that of EFC. However, it is important to note that the capital cost calculations for EC are based on a technology that is already well established and with only relatively marginal future equipment cost savings expected. In contrast, EFC is a new technology, with significant future technology improvements expected.

Jan 1, 2009

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.

By P. G. Roden, G. A. Maki, P. J. Fullmann

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. The paper will deal with the various aspects of the project from conception to its present state. Key Words: stacking, mobile stackers, Linatex Separators, potash mill tailings, reclaim brine ponds, settling ponds, tailings pile. IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65% solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dikes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1986

By Jeffrey Mitsopoulos

King County?s (KC) Brightwater Conveyance Project in Seattle, Washington involves the construction of approximately 21 kilometers (13 miles) of bored tunnel, in three contracts, with four TBM?s which produce large amounts of real-time digital mining data. To facilitate the management of TBM data with a single interface and assist in project Quality Assurance, KC?s Construction Manager (Jacobs Engineering) recommended the use of the software TPC (Tunneling Process Control), developed by Babendererde Engineers GmbH. The paper demonstrates how TPC was used for oversight, analysis and QA on a complex tunneling project and how contemporaneous review and management of data results in a better understanding of TBM performance than can be obtained by retrospective analysis of data.