Search Documents

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By K. Verghese

Neutron capture prompt gamma-ray analysis provides the best method for on-line analysis of the elemental composition of large volumes of bulk material. This paper summarizes the Monte Carlo models which simulate the radiation transport within two such analyzer systems; namely, the borehole configuration and the conveyor belt configuration. The models are useful in the design optimization of the analyzer systems, in minimizing the amount of experimental calibration data for calibrating these analyzers, and in investigating the detection sensitivity for different elements. The computational scheme in these models is made extremely efficient by the use of various powerful variance reduction methods and by efficient data management. Experimental verifications of the two models carried out in the laboratory indicate very good agreement with the Monte Carlo results.

Jan 1, 1984

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By R. C. D. Phillis

Conventional stoping in hard rock mining is largely considered an operational environment. This paper suggests that stoping falls within the realm of a project management environment typified by uncertainty, variation, and large numbers of interdependencies. Stoping was then equated to a micro-project with many simultaneous activities that had to be executed accurately using finite resources within limited shift durations in order to reach specific goals. Critical chain project management (CCPM) principles were applied to the stoping activities, and the results showed that the number of blasts per panel can be significantly increased by successfully moving the distribution of work as close as possible to the start of shift. Critical chain principles also assisted in facilitating re-focusing and teamwork among stoping crews as well as between day- and night-shift crews. The main recorded success was in managing inherent protective capacities/local contingencies/fat/buffers that are found in all projects. The impact on mine health and safety (MHS) was significant as individual operators and crews became convinced that they could perform all stoping tasks (activities) without compromising accuracy or speed.

Jan 1, 2011

By Priyadharshini M. R., Premalatha K

"Abstract With the development in the construction of heavily loaded structures, the necessity of pile foundations has increased. For the transfer of heavy loads, it is mandatory that the piles need to be socketed in the underlying rock strata. The load transfer in bored rock socketed piles is by end resistance or the combination of shaft and end resistance which in turn depends on the length of the rock socket. The determination of socketing length of the pile at present is mostly based on a few factors which affect the pile load transfer mechanism. The effect of all the possible factors involved, need to be studied in proposing guidelines for the design of rock socketing length of the pile. Analyses are carried out using finite element analysis software (PLAXIS 3D Foundation) to understand the influence of the thickness of overlying strata for different socket lengths of piles in weak rock. From the load settlement curves, the influence of the overlying soil on the rock socket length isobserved and an effective rock socket length is proposed.IntroductionThe determination of socketing length of the pile at present is mostly based on a few factors affecting the pile load transfer mechanism, which sometimes give a better design and sometimes an uneconomical design. Too much socketing length results in more construction time and higher costs. Therefore, the effect of all possible factors involved need to be studied in proposing guidelinesfor the design of t h e r o c k socket length of the pile.The factors that affect the termination criteria of the rock socketed pile are the capacity requirement, thickness and properties of the overlying soil, characteristics of the founding strata, drilling tools used, roughness of the rock socket and nature of loading.A comprehensive study was performed to understand all the above mentioned factors in different types of rocks. In this paper discussion is made on the settlement results, specifically the influence of overlying sand of different densities above a weak rock. The influence of stress developed is not discussed, keeping in mind the size of the paper under study."

Jan 1, 2014

By Yong Xian, Zhaohui Sun, Honggang Zhong, Qijie Zhai, Jie Sun

Vacuum refining is admitted as an effective means to remove impurities in the process of alloy smelting. In this paper, Orthogonal and single factor experiments were carried out to investigate effects of multiple factors, such as superheat degree of the melt, degassing time and vacuum degree, on the vacuum refining process. The results showed that the best removal rate of oxygen and nitrogen is up to 82.71% and 61.3%, respectively, due to high vacuum degassing efficiency. It is found that the superheat degree is minimal impact on the deoxidization rate, in addition, nitrogen removal is controlled by the degassing time. The inclusions exist in the AlV55 alloy are mainly composed of oxides and vanadium-nitrogen compounds.

Jan 1, 2015

This paper describes the economic study of longwall versus bord and pillar mining using all continuous miners for a colliery located at the South Coast district of New South Wales, Australia. In this district longwall mining appears to be a better economic proposition than bord and pillar. The internal rate of return on investment is found to remain approximately constant for each method irrespective of life. The economic importance of percentage extraction of coal is shown to be small for high values of minimum rates of return, becoming more significant as the minimum rate of return decreases.

Jan 1, 1980

By G. S. Bartlett

The theme of this Colloquium, survival strategies, not only conveys a sense of urgency but also takes cognizance of the fact that, as in the political arena, tough decisions have to be made and acted upon in the years to come. It is therefore appropriate that the SAIMM, as spokesman for the metallurgical industry, should be dealing with these issues at this time, and I wish to commend the organizers of this Colloquium for focusing on a mater as important as the future of this great industry. In view of this, I regard it as an honour and privilege to officiate on this occasion, where the best of South Africa's brain power in the metallurgical field will be harnessed with a view to moulding strategies for survival.

Jan 1, 1993

In accordance with the usual custom, manuscripts to be presented at the next meeting of the Institute must be in the hands of the, Secretary before July 1, 1917. Manuscripts to be properly distributed in advance of the meeting must be in the hands of the Secretary before June 1, 1917. At the last meeting of the Institute 45 papers were presented, and 42 of them were actively discussed. This experience makes us believe that advance distribution is the best possible means of getting a good discussion of papers and of securing for them the interest of the members of the profession. It will be impossible, however, to give the papers proper distribution if they bare not received before June 1, 1917.

Jan 4, 1917

Future metal prices play a direct role in both the economic evaluation and short to medium planning of a mine scheduling sequence. It is difficult to predict with accuracy the future price of volatile metal commodities, however, it is possible to fix some future metal price, outside of long term contracts by the selling of futures contracts through a commodities exchange. The futures contract represents a fixed amount of a specified quality of a commodity for future delivery at a predetermined price. Several different types of hedging are possible, one in particular which is best suited for mining companies. There are relative advantages and disadvantages when trading in futures contracts and particular reference is made to gold contracts on the Sydney Futures Exchange.

Jan 1, 1980

By Eric H. Brown

One of the best methods by which the results of accident-prevention work can be measured for any particular period is to keep an accurate record of the accident experience, which may then also be compared with the experience of others. The purpose of this report is to compare records of the salt-mining companies operating in Louisiana, and their assistance in making available their accident records is gratefully acknowledged. PRODUCTION Four companies produce salt in Louisiana -Avery Salt Co., Avery Island; Jefferson Island Salt Mining Co., Jefferson Island; Myles Salt Co., Weeks; and Carey Salt Co., Winnfield. Three of these companies operate within 30 miles of each other in the southern part of the State, and the other operates in the central part.

Jan 1, 1938

By G. Brackebusch, S. J. Jung

Backfilling techniques are widely used in large-scale underground mines. Massive pillars, which have been left in place for stability, limit mining activity. Backfilling allows safe recovery of the ore remaining in pillars and assures long term stability. In deep mines expected high stress can be relieved with the backfill. Initially, waste rock was used to fill the openings with mixed results. The need to improve safety and reduce costs has prompted the industry to investigate alternatives. Hydraulic filling with Portland cement added has shown considerable promise, but little has been done to define the parameters of design effective system. The purpose of this study is to determine the relationship between backfill and mining components that can be used to effectively design a best-case hydraulic backfill.

Jan 1, 2000

By S. R. Gilbert, C. O. Bounds, R. R. Ice

"Many ores are upgraded to produce auriferous sulphide concentrates (principally pyrite) which are not amenable to direct cyanidation. Often these refractory gold-bearing concentrates contain undesirable elements such as arsenic, antimony, etc., which present environmental and/or processing problems. The pretreatment techniques most often considered for processing these concentrates prior to cyanidation include roasting, pressure oxidation, chemical oxidation, pre-aeration, and recently, bacterial oxidation. In this paper, the technical performance and economics of bacterial pre-oxidation vs the classical roasting approach for treating a specific auriferous pyrite concentrate are compared. The results provide flow sheets, preliminary operating and capital cost estimates, and rates of return for the two processes and demonstrate the potential advantages of bacterial pre-oxidation. IntroductionThe increased attention that gold has received in the last ten years has prompted mining companies to look for lower grade orebodies. Many of these low-grade ores do not respond well to conventional direct cyanidation recovery techniques. As free-milling ores decline, gold is sought in refractory environments which, ultimately, drive up the treatment costs.There are a number of reasons for a gold ore to be termed refractory, most of which can be identified by thorough mineralogical examination. The mineralogical occurrence of gold can, to a great extent, impact the method by which the ore is treated and, consequently, the capital and operating costs. Gold in a refractory ore can often occur as discrete particles locked in a host of silicate or carbonate gangue, or associated with sulphides or sulphosalts. Depending on its particle size, gold can be liberated and recovered by mechanical size reduction such as regrinding. This approach is most effective for gold in the 10 - 50 micron range. Gold can also be associated with clay, iron hydroxides, or other minerals which tend to coat the gold surface and inhibit the penetration of the cyanide solution, resulting in poor plant recovery. Because of their resistance to cyanide dissolution, gold tellurides and other refractory gold minerals are also responsible for losses to the tailings. For these reasons, it is paramount that the mineralogical occurrence of the gold be thoroughly and accurately determined before selecting a final process flowsheet."

Jan 1, 1988

By S. J. Anderson

To deftne the capabilities of a nonexplosive excavation concept, the Bureau of Mines conducted reduced-scale laboratory tests of a mechanical excavation tool called a rock splitter. The splitter investigated was capable of applying combinations of radial and axial loads to rock when placed in a predrilled hole. Experiments conducted with the tool in concrete, limestone, and granite proved it capable of excavating all three materials. Break geometry in these three materials was the same, which encourages the prediction of performance in all rocks. The design of the radial-axial loading splitter's feather components significantly affected the tool's performance. It appears the design of this in-hole component should be tailored for the rock to be excavated.

Jan 1, 1987

By W. G. Pariseau

This Bureau of Mines report is an evaluation of the state of knowledge about gravity flow from bin hoppers, the most commonly used method of handling bulk materials where the force of gravity is used. The requirements for flow to be initiated and to continue, formulas developed experimentally or mathematically from various assumptions to describe the materials flow, and the question of whether or not a material will flow over the entire cross sectional area of the bin hopper according to the flow regime developed are the primary areas discussed. The work of A. W. Jenike, whose pioneering investigations raised bin hop- per design from the trial and error state, is examined in depth and its limitations and assumptions are pointed out. Bin hopper design depends heavily upon prior experience, and suggestions for further studies of bin hopper flow to include the effects of feeders are made.

Jan 1, 1972

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen's original discovery.

Jan 1, 1956

By Virgil J. Stachura

The Bureau of Mines has investigated techniques and instrumentation that measure accurately the airblast overpressures from surface mine blasting. The results include equivalencies between broadband research instrumentation and commercially available impulse precision sound levels meters measuring: root-mean-square, peak, fast, slow, impulse, A and C weighting, C-weighted sound exposure level (CSEL), and "linear" (flat) response. These values were obtained from field measurements and broadband FM tape recordings of production blasts at area and contour coal mines, limestones quarries, and iron mines. Frequency response was determined for 14 commercial systems.

Jan 1, 1981

By S. Hoskins, S. Chiovelli

"The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd. is in excess of $450 million. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trials where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trials will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work. IntroductionSyncrude Canada Ltd, located in northern Alberta, Canada, operates a mining, extraction, and upgrading facility that removes bitumen from oil sand to produce synthetic crude oil. Oil sand is mined from the orebody using conventional open pit mining techniques. Recently, the mining scheme has changed from a dragline/bucketwheel/conveyor system to a shovel/truck/crusher/hydrotransport operation as depicted in Figure 1. Since the start of production in 1978, the identification, development and application of wear protection has been an ongoing challenge due to the abrasive nature of the oil sands and the massive volumes of materials that are moved. The use of various materials and application processes along with component design modifications has resulted in significant improvements in both productivity and reliability (Adamic et al., 1995; Llewellyn, 1996, 1997; Anderson et al., 1998; Chiovelli et al., 1998).In an effort to continuously improve the operation, Syncrude has been quick to adopt new wear technologies. As seen in Figure 2, since the start of operation, a variety of materials have been used to increase wear performance and ultimately equipment reliability and availability. Although Figure 2 does not show a time axis, the bottom axis may also be used to represent a time progression for the predominate use of these materials at Syncrude. Tungsten carbide metal matrix composite (WC-MMC) overlays are currently the materials of choice for most of Syncrude’s critical production applications. Metal matrix composite overlay technology has potential for significant improvements and Syncrude is actively working with powder consumable manufacturers to advance this technology."

Jan 1, 2004

The pyrite-sphalerite-galena and barite orebodies at the Rosebery mine are concordant with the shale host rock and have been deformed into one system of folds with an associated axial plane cleavage. The folds are tight and overturned with east-dipping axial planes. Folds in the sulphide ore are commonly disharmonic, particularly between adjacent bands of different composition.Concentric style folds occur in the competent bands, e.g. pyrite-rich bands. Similar style folds are predominant in the less competent sphalerite-galena-rich bands and also in the shale of the host rock. The trends and plunges of the fold hinge-lines are variable but axial planes are of reasonably constant orientation throughout the mine area. The folds in the orebodies are of limited axial extent, approximating to conical folds, and are arranged in en echelon patterns. The fold system was possibly formed in one period of folding by heterogeneous strain that may have been caused by the presence of a mass of tectonically mobile sulphide ore. Lineations parallel to the ore/host rock contacts appear to reflect movement between the ore and the host rock during folding.

Jan 1, 1972