Search Documents

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

By M Quinteiro, Å Sundqvist

What is special about being a female mine manager? We do not believe that the challenge is greater for women in managing a mine compared to managerial positions in other male-dominated businesses. The challenge lies in the fact that it is a male-dominated business. Being a leader belonging to a minority creates a situation where competence not only lies in having technical knowledge or general leadership characteristics, but also in acquiring an understanding of the male norm and being able to behave and communicate effectively in the organisation.In order to move towards a better gender balance at senior levels it is important to set measurable objectives on desirable proportions between women and men at management levels within the company. Focus and action are required to achieve this goal. At LKAB, the current target is to reach 25 per cent women in the total workforce by 2020. To date, LKAB has reached 19.4 per cent women in the total workforce, and the number of women in management positions is 19.9 per cent.It is of vital importance to create a non-discriminating working environment to achieve equal opportunities at the workplace, to be able to use the whole workforce as a resource for recruitment of professionals and managers, thereby improving decision-making, productivity, efficiency and profitability.Women as mine managers is not a utopia, but rather an effect of long-term investments in actions that result in equal opportunities for all employees.CITATION:Quinteiro, M and Sundqvist, Å, 2016. Women as mine managers – a utopia?, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016) , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Ore from the "Staimite" lode in the Oonah mine, Zeehan, has a complex composition and contains an exceptional number of elements. Its chemical composition has been indicated by the following published figuresà

Jan 1, 1931

By Duane A. Smith

They are gone now. Gone like that long ago generation that gave them birth. The Homestake Mine, nestled in the northern Black Hills, closed in 2001 after 125 years, the longest run of any major American gold mine. The Homestake Mining Co., which guided its destiny for those many years, is gone too. It merged with Barrick Gold. The Hearst family, which guided the early destiny of both, has long since gone beyond its mining heritage and into the national and even international spotlight. The mine and the company passed from the scene with as little fanfare as heralded their birth, amid the Black Hills gold rush of the 1870s. They both grew into American mining legends, as did the town they sired and nurtured, Lead. In a real sense, the mine and the company symbolized one of the last links to a vanished world and a mining era.

Jan 1, 2003

By D. D. Munro

Finsch Mine is a kimberlite diamond mine located at Lime Acres in the Northern Cape Province of South Africa. The mine was founded in 1961 and started surface mining in 1964. Underground production commenced in 1990 using a modified blast-hole open stoping method for the mining of Blocks 1, 2 and 3. Block 4 is currently being mined as a block cave. The process of identifying and optimizing a method to mine the Block 5 orebody started in 1991, and in 2006 incline caving was identified as being technically feasible. This paper aims to document the process employed in developing this method by the Block 5 prefeasibility team as well as discuss the technical challenges encountered during this process. The paper commences with a history of Finsch Mine and highlights the complex geology and threat of sidewall failure that prompted the decision to use block caving as the mining method for Block 4. A literature study of mines that implemented mining methods upon which the incline cave was conceptualized is then presented. These practices were then used to form the basis for the designs on which the initial geotechnical modelling was done and built upon through an iterative process of modelling and design changes. The ventilation of the mining area, initial productivity simulation results, and the applicability of automation and comminution processes in the incline cave are also presented. The paper concludes with an investigation into some of the challenges of the mining method, and shows that that incline caving is a technical option available for further investigation in determining the optimal mining method to be employed at Block 5, Finsch Diamond Mine. Keywords massive mining, incline caving, geotechnical modelling.

Jul 1, 2013

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler?s performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of ~43 per cent (LHV basis). This operating unit has also proven the use of the world?s first FW/BENSON? vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 × 1000 MWe solid fuel power block.

Jan 1, 2012

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By Theo. A. M. Salet

The historic centre of one of the most beautiful cities in Northern Europe -Amsterdam - is being excavated to accommodate the new North/South metro line. This new line is due for completion in 2012, and will link the Buikslotermeerplein district north of the harbour, underneath the Central Station and the old city with its gables and picturesque canals, to the commercial centre in Amsterdam Zuid/WTC. Three underground stations are being construction in the old city at Rokin, Vijzelgracht and Ceintuurbaan. The logistics of working in the middle of an historic city are demanding -maintaining tram, vehicular traffic and pedestrian access along narrow streets, providing suitable protection for the public alongside the working areas, arranging adequate delivery routes, as well as monitoring the old and mostly historical buildings for potential settlement. Safety of both the public and adjacent properties is paramount. Diaphragm walling - 1.2m & 1.5m thick and up to 48m deep - was chosen as the support system for the three deep metro stations. Challenging engineering as well as state-of-the-art equipment to construct the diaphragm walls was needed in order to meet the tight working specifications, in the narrowest locations imaginable. Extreme conditions call for innovative solutions.

Jan 1, 2006

By M. M. Manamela

Paper written on project work carried out at the University of Pretoria in partial fulfilment of the requirements of the B Tech degree at the Tshwane University of Technology This work tested whether ore particle size affects the carbon-based pre-reduction of titaniferous magnetite. Pre-reduction is performed at a temperature of some 1100°C in a rotary kiln, in the Highveld Steel process. Laboratory isothermal reduction measurements were performed with ore-coal mixtures at this temperature, to test the effect of ore particle size. The results show that size does limit the degree of reduction for particles larger than 15 mm.

Jan 1, 2005

By A Croll

A panel cave using LHDs for ore extraction came into production at Premier in 1990 at a depth of 630 metres below surface on the western side of the mine in the BA5 mining block. A post-undercut mining sequence was used with all development on both the undercut and production levels completed prior to the undercut being advanced over the pre-developed drawbells. Support and rock mass damage on the production level was extensive as the undercut moved overhead. Undercutting and coarse fragmentation created problems. The mining sequence was changed to an advance undercut with the minimum of development and support undertaken on the production level prior to the undercut moving overhead. Only once the abutment stresses had stabilised were drawbells developed and final support installed. The height of the undercut drill design was decreased from 18 to 13 metres. The changes resulted in markedly less rock mass and support damage on the production level. Lessons learned in the BA5 mining block on the 630 level were incorporated into planning and scheduling the BB1E mining block which came into production on the 732 metre level on the eastern side of the mine in 1996. An advance undercut mining sequence was planned, undercut height was minimised and undercutting parameters were optimised in terms of the BA5 experience. Numerous problems still occurred. As the undercut area increased in size severe spalling from the cave back resulted in vertical propagation of the cave to a height of 30 metres instead of the planned 13 metres. The resultant coarse fragmentation created secondary blasting problems and an excess of undercut ore that had to be loaded and trammed, slowed the rate of undercut advance. The planned mining sequence was compromised and considerable support and rock mass damage resulted on the production level below. Once these problems had been overcome the undercut advanced at the planned rate and continuous caving initiated at the predicted hydraulic radius. At a later stage the unexpected ingress of water hampered undercut drilling and slowed the rate of undercut advance in a section of the cave. Leads and lags between adjacent tunnels and the overall face shape could not be developed as planned. The rate of natural horizontal cave propagation exceeded the rate of undercut advance and three undercut drilling tunnels were extensively damaged. More tunnel development on the production level prior to undercutting than was planned resulted. The slow advance of the undercut and high abutment stresses caused extensive damage to installed support and the rock mass on the production level, 15 metres below. Experience in the BB1E mining block on the 732 metre level has taught that an advance undercut mining sequence reduces damage on the production level markedly. Extremely tight control on the rate of undercut advance, leads and lags between adjacent tunnels and overall undercut face shape as well as extraction ratio, tunnel development and support sequence on the production level below is required. Premier Mine plans to implement a block cave at a depth in excess of 1000 metres within the next decade. All the experience gained on current mining levels together with data collection and numerical modeling is being used to plan the proposed mining operation. The geotechnical challenge of mining at this depth in weak rock has been identified as the greatest risk to the project. Challenges centre around adopting the correct mining sequence, limiting the extent of rock mass damage associated with undercutting and effective support. The hydraulic radius needed to initiate caving, fragmentation, drawpoint spacing, secondary blasting and the possibility of seismicity are geotechnical concerns that are being addressed. Results to-date suggest that a pre-undercut mining sequence with all development and support on the production level carried out only after the undercut abutment stresses have passed overhead will have to be implemented.

Jan 1, 2000

By Robert Martin

New Millennium ?a new project for an experienced mine building team ?Owns 100% of KeMag(Harris Lake) property ?Owns 80% of LabMag(Howells River) property -20% owned by Naskapi Nations of Kawawachikamah ?All founding directors are mining professionals : Geologists or Mining Engineers ?All have extensive experience in the iron ore industry ?The Project Office is located in Montreal, lead by a team of experienced iron-ore professionals Project Overview Geology & Resources Market Prospects Process & Product Development Development Plan Questions

May 1, 2007

Base metal sulphide mineralisation on the northern end of Great Barrier Island is spatially associated with hypabyssal intermediate to acidic intrusives, in transgressive structures in indurated, complexly deformed greywackes and argillites. Copper predominates in the mineralisation, with minor accompanying lead and zinc and also some gold and silver. However, in some cases lead or zinc may be the dominant constituent. The mineralisation is generally characterised by only narrow envelopes of weak alteration (propyliticassemblages dominated by chlorite and epidote) and with only minor amounts of quartz accompanying the sulphides, which form a cement in zones of hydraulic fracturing. There are two distinct structural settings to the mineralisation: at MinerÆs Head, in a structurally complex situation in a shell-like zone of crackling in hornfelsed greywacke, in association with both north- and east-striking fractures and rubble breccias associated with the apical part of a large intrusive; and in very narrow, but very strike-persistent, 1inear steeply-dipping fracture zones, exposed on the north coast and inland areas near Tataweka.

Jan 1, 1984

By A. W. Dougall, T. M. Mmola

"SynopsisThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs) – which are those areas of performance that are reflected explicitly or implicitly in the vision and strategies of an organization and reflect the critical success factors of the organization. This paper is a review of key performance areas in the southern African mining delivery environment. The KPAs discussed in this paper have been identified by comparing KPAs of the several mining houses engaged in surface mining operations in southern Africa and then extracting those KPAs that are common to most of them. Although the authors support the view that each organization should develop KPAs to specifically fit its needs, the study reveals that five KPAs – safety and health, costs, product quality, fleet management, and delivery should form a default list that covers the key areas that any organization should consider when choosing KPAs. KPIs are those subsets of KPAs that we measure in order to manage KPAs.IntroductionThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs), which are ‘those areas of performance that are reflected explicitly or implicitly in the vision and strategies of the organization’ (Barker, 1997). The terms KPA and KPI (key performance indicator) are often used interchangeably – whether correctly or erroneously is debatable. KPIs are ‘quantifiable measurements, agreed to beforehand, that reflect the critical success factors of an organization’ (O’Neill, 2007). Each KPA probably has multiple KPIs associated with it."

Jan 1, 2015

By G Siboni, A Correa De Araujo, M Gotelip Barbosa, M J. Venturini

In support of the development of its Liberian iron ore project, ArcelorMittal Mining Research and Development (AM Mining R&D) has performed characterisation and beneficiation test work on drill core samples received from the proposed mine area. In addition to this, a sinter feed product was composed by blending and processing the drill cores in order to predict sintering performance of the ore. This article presents the methodology used to prepare the drill core blend for characterisation, as well as describe the sinter pot trial. The results are presented, demonstrating how important this type of study is for the development of an iron ore deposit.CITATION:Gotelip Barbosa, M, Siboni, G, Venturini, M J and Correa de Araujo, A, 2017. The use of drill core blends to predict sintering performance, in Proceedings Iron Ore 2017, pp 297–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

By G. Cockburn

Nkomati Nickel JV exploits the ores of the Uitkomst Complex near Machadodorp in the Waterval Boven district in South Africa?s Mpumalanga Province. Due to factors such as the remote location, stellar growth in production, opencast mining methods, and ore characteristics, a number of innovative processing options were selected. Nkomati has undertaken numerous initiatives over the last few years to improve plant running times, metallurgical performance, and operational profitability. Great emphasis has been placed on effectiveness of management control systems. A number of initiatives such as short interval control and time?in-state metrics have been implemented. A focus on improvement on availability and asset utilization of key items of equipment has been particularly effective. While the ores are remarkably similar to the Merensky and UG2 reefs, the relatively high base metal sulphide content and mineralogical characteristics make metallurgical treatment somewhat different to the ores of the Bushveld Complex. The low head grades and flotation kinetics distinguish Nkomati from other base metal operations. Numerous milling and flotation optimization initiatives have resulted in dramatic improvements in throughput, recoveries, and concentrate grades. This paper discusses the metallurgical, operational, and management challenges and the outcomes obtained.

Jan 1, 2014