Search Documents

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Hand arm vibration syndrome (HAVS) affects industrial workers exposed to long term hand-transmitted vibration from powered-tools. Peripheral neuropathy is a major component of the symptom complex of HAVS. Long term exposure to vibration causes myelin damage in peripheral nerves and reduces nerve conduction velocities in rats1. This study addresses the effects of acute vibration at constant acceleration of 49 m/s2 on myelinated fibers in peripheral nerves in Sprague-Dawley male rats using the ‘rat-tail vibration model,’ which simulates hand-transmitted vibration2. Methods Male Sprague-Dawley rats (~300 g) were assigned to vibration groups: 1 hr continuous vibration at 60 Hz; 4 hr continuous exposure at frequencies of 30, 60, 120 or 800 Hz; immediate and 24 hr following a 4-hr cumulative exposure of continuous and intermittent vibration at 60 Hz. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage accelerated by a B&K motor type 4809 and vibrated. Intermittent vibration was delivered in bouts of 10 min vibration alternating with 5 min rest periods repeated over 6 hr. Sham controls were restrained without vibration. After vibration exposure, the rats were anaesthetized, and the ventral nerve trunks from the proximal tail segment 7 were fixed in glutaraldehyde, embedded in epon-araldite and sectioned at 0.5 µm thickness and stained with toludine-blue for morphological quantitative analysis. The total number of myelinated axons in each cross-section of the nerve was counted using the Image J software. Myelin damage was identified by focal increase in area and intensity of toludine-blue staining and unraveling of the myelin sheath. Statistical analysis for comparing sham and the different vibration groups was done using Dunnett’s test. Animal treatment and all surgical procedures were approved by the institutional review board and compiled with the Laboratory Animal Welfare Act. Results The rats tolerated continuous vibration very well and exhibited no behavioral signs of stress. When exposed to intermittent vibration, there was increased vocalization, a startle reflex at the beginning of each bout of vibration, deposition of porphyrin around the eyes and transient hypersensitivity to touch.

Jan 6, 2006

By Lucio Fabio Cassiano Nascimento

A determinação dos parâmetros cinéticos de cura de uma resina polimérica, bem como do compósito de matriz polimérica constitui importante ferramenta científica e tecnológica para processos industriais. No presente trabalho foi utilizada a técnica de calorimetria diferencial de varredura (DSC), prevista pela ASTM E698, com taxas de 5, 7,5 e 10°C/min para determinação da energia de ativação “E” (kJ/mol), fator pré-exponencial “Z” (min-1) e o tempo médio para alcançar 50% de cura “t1/2” para o epóxi puro e para o compósito reforçado por fibras de malva, em temperaturas variando na faixa de 25ºC a 100ºC. Os resultados mostraram que o tempo médio de cura de 24h, utilizado para a produção de placas de resina epóxi DGEBA-TETA ou compósitos de epóxi reforçados com fibras naturais, pode ser reduzido consideravelmente.

Oct 30, 2017

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By Miyuki Morioka, Michael J. Griffin

Discomfort, annoyance, or interference with activities due to exposure to vibration is only expected if the vibration exceeds the threshold for the perception of vibration. When there is more than one vibration input to the body (e.g. at the hands, seat and feet), the sensation is first experienced at the location with greatest sensitivity. Knowledge of differences in the thresholds of perception for vibration at the hand, seat, and feet should assist the identification of sources of discomfort caused by vibration. Perception thresholds for vibration have been determined in several studies, but only a few studies have investigated perception thresholds in the horizontal direction for hand-transmitted vibration 1, 6 or whole-body vibration 4-5, and there has been little consideration of perception thresholds for the foot resting on a vibrating surface. This study determines absolute thresholds for the perception of sinusoidal lateral vibration, examining the effect of vibration frequency (8 to 315 Hz for the hand and foot; 2 to 315 Hz for the seat) and the effect of input location (the hand, the seat and the foot). Methods Three groups of twelve males aged between 20 and 29 years participated in the experiment. Subjects in each group attended an experiment to determine perception thresholds for lateral vibration via either a rigid handlebar (30 mm diameter) at the left hand (left hand), or a rigid contoured seat (250 mm x 150 mm), or a footrest at the left foot (30.5 mm x 10.5 mm with 10-degree inclination). For the non-exposed hand (right hand) or foot (right foot), a stationary handle and footrest with the same dimensions as the vibrating handle and footrest were provided so that the same body posture was adopted among the three groups of subjects. An up-down (staircase) algorithm was employed to determine thresholds in conjunction with a three-down one-up rule. A single test stimulus (2.0 seconds) was presented with a cue light illuminated during this period. The task of the subjects was to indicate whether they perceived the vibration stimulus or not. The threshold was calculated from the mean of the last two peaks and the last two troughs, omitting the first two reversals. Results The median absolute thresholds of the 12 subjects determined at each frequency for the hand, seat and foot are shown in Figure 1. A frequency dependence of the threshold contours within the investigated frequency range is evident, with similar shape to the threshold contours

Jan 6, 2006

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By Neil J. Mansfield, Setsuo Maeda

The purpose of using experimental subjective and/or perception methods is: (a) to understand human subjective impressions of the physical characteristics of vibration; (b) to determine the relationship between the subjective perception of some aspect of the vibration and an evaluation index of the physical vibration characteristics; and (c) the establishment of target values for design of vibration environments in terms of human sensation of vibration characteristics. In order to understand the relationship between a physical measure of the mechanical vibration and the subjectively perceived aspect of the vibration environment, experimental methods shown in Table 1 have been used1. [ ] The constant measurement methods of Table 1 are mainly used for measurement of the threshold of human sense. The subjective scaling methods are mainly used for obtaining subjective (or proportional) scaling between the perceived quantity and physical quantity. In this review, the fundamental approach of experimental methods for obtaining the target values used in the design of vibration environments, and the different findings between the subjectively perceived methods for evaluating human response to vibration characteristics and the physical quantity of the vibration environment are summarized. Fundamentals of Subjective Scaling The relationship between the experimental psychological methods for providing target values in the design of the vibration environments and the physical quantities is illustrated in Fig. 1. Vehicle mechanical vibration can be characterized using many metrics, and these can be considered the ‘input’ to the human. In order to predict subjective responses to the vibration, it is necessary to link the characteristics of the source of vibration and human reactions, the ‘output’.

Jan 6, 2006

By Fabiano Della Libera da Silva

Este artigo propõe uma metodologia para a construção de um Referencial Estatístico para a Utilização Física de equipamentos de mina. Para tanto, calcula-se um valor mensal (RE) apoiando-se em conceitos importantes para a operação de mina e que estão e inter-relacionados, como o comportamento sazonal da precipitação pluviométrica, o Teorema do Limite Central e a Gestão da Lacuna de Resultado. A metodologia proposta foi aplicada em uma mina de ferro a céu aberto e às frotas de transporte de um complexo minerador no Norte do Pará.

Aug 17, 2017

By C. W. Goodale

TOMBSTONE, a name not exactly full of cheerful suggestion, has a great record as a mineral producer and a colorful history as a frontier mining camp. The only practical route to Tombstone in the early 80's was by way of San Francisco and Los Angeles. The Southern Pacific was building across Arizona, and a sleeper was attached to a construction and freight train at Los Angeles, and was trailed slowly across the Colorado Desert to Benson in the San Pedro Valley. Thence one staged 26 miles to Tombstone, which is located near the foot of a range of hills at an altitude of about 4500 ft.

Jan 1, 1925

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By Yumi Nakashima, Setsuo Maeda

Vibration magnitude and frequency of the z-axis vehicle seat are time-variant, which are influenced by not only vehicle vibration characteristics themselves but also road surfaces, speeds and the human body. There is little in the current reporting about evaluating and analyzing automobile seat vibration that focuses on the time-variant. Yaguchi et al.1 has proposed a method to evaluate automobile seat vibration that is based on judgments using a subjective mental state. Their method focuses on the time-variant magnitude of the peak frequency on a power spectrum density. However, their method has no consideration of all the frequency contents of the discomfort, nor comparison between different peak frequency vibrations. Suzuki2 has emphasized that the vehicle vibration should be judged by a series of vibration stimuli to evaluate, because the vehicle vibration is time-variant, which isn’t a matter of the relationship between a single vibration stimulus and a subjective response. He clarified that the human sensation to the vehicle vibration discomfort changes every moment showing the relationship between the frequency-weighted r.m.s. acceleration calculated every 5 seconds and the category judgment to vehicle vibration discomfort every 5 seconds. However, his study doesn’t show what parameter connects to the subjective final judgment to vehicle vibration. Therefore, we applied the method similar to ISO100563 considering the time-variant to the vehicle seat z-axis vibration evaluation. The new method for the vehicle seat vibration considering the time-variant was examined on the hypothesis that the final subjective evaluation must be conducted from the judgment summarizing a series of vibration stimuli. Methods The vibration bench system, which reproduces the movement of a vehicle floor, was used for the experiment with the single-axis (vertical direction) four-post road simulator system, which is usually used for a car, as shown in Fig.1. The experiment was done on the right side of the vibration bench using the floor vibration which was 5.5 minutes, 0.822 m/sec2 (Wk) over the range 0.5-20Hz with 4 male subjects (age ave21.5, SD0.5, weight ave75kg, SD7.91kg, height ave166.8cm, SD5.2cm) and 4 suspension seats. As Fig.2 shows, subjects evaluated the degree of discomfort every 5 seconds to each seat vibration measuring the seat z-axis vibration acceleration. [ ]

Jan 6, 2006

By Vinicius Andres Strey

A estruturação organizacional da rotina operacional em processos de gestão já está consolidada no ambiente de Tecnologia da Informação (TI). O ambiente de Tecnologia de Automação (TA) compartilha características semelhantes à TI, porém implantar processos de gestão no ambiente de TA de uma empresa já existente demanda uma série de ações para garantir que este sistema de gestão está alinhado aos objetivos da organização, que este sistema de gestão está sendo realmente utilizado e sustentável e, principalmente, que este sistema de gestão é aderente aos requisitos da rotina da TA. Os principais retornos sobre o investimento neste tipo de projeto são em termos de organização das atividades e produtividade de pessoal, de disponibilidade dos ativos pela resposta planejada e rápida a falhas e de visibilidade da TA dentro da organização. Este trabalho define as diretrizes para o desenho e implantação de processos de gestão. Estas diretrizes foram empregadas em projetos de Metais e Mineração, como no caso específico do Departamento de Automação e Instrumentação da Samarco Mineração.

Aug 16, 2017

By João Lucas Lautenschlager Cortez Alves

Foi implementado um modelo matemático transiente e tridimensional para prever os campos de temperatura e composição presentes no sólido e poça de fusão durante um processo de soldagem a arco. O modelo foi desenvolvido com base nas equações de conservação macroscópicas de calor, massa e espécies químicas, que foram solucionadas pelo método dos volumes finitos. Os resultados do modelo mostraram boa aderência com soluções analíticas. Foram apresentados os efeitos de mudança na velocidade e potência de soldagem na distribuição de temperatura obtida e no formato da poça de fusão para soldagem em uma chapa de liga Al-6,5%Cu.

Oct 30, 2017

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By Rodrigo Camargos Barroso

Os fenômenos de solidificação no lingotamento contínuo são altamente dependentes da velocidade de lingotamento e das condições de extração de calor do molde. Por sua vez, equipamentos como os agitadores eletromagnéticos, alteram significativamente o escoamento na região do molde, influenciando o perfil térmico e ajudando na redução do calor de superheat. Simular simultaneamente o escoamento, o transporte de energia e a solidificação é um dos objetivos deste trabalho. O modelo emprega o software Ansys/Fluent e é aplicado ao lingotamento contínuo de moldes redondos. Como resultado, obteve-se os mapas de temperatura e a espessura de casca na saída do molde para diferentes velocidades de lingotamento e correntes de agitação. Experimentos realizados em planta buscam comprovar as previsões do modelo. Espera-se, por fim, criar um padrão operacional no lingotamento contínuo buscando otimizar o uso do agitador eletromagnético em função da velocidade de lingotamento e da temperatura de superheat.

Jul 30, 2018

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

Domestic Production and Use: In 1976, 12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 63% of production capacity. Washington, Oregon, and Montana accounted for 36% of the total production; Gulf Coast States 19%, Northern States 29%, and other Southern States 16%. Based on published producer prices output of primary metal in 1976 was valued at $3.8 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1976 building accounted for about 25%; packaging 22%; transportation 19%; electrical 13%; , consumer durables 8%; and other uses, 13%.

Jan 1, 1977

By Oswald J. Heinrich

THE origin of spontaneous combustion in collieries is, of course, chiefly due to bad system in laying out the pits, unclean workings, insufficient ventilation, and neglect in damming off works after they are exhausted of the main coal. This is particularly indispensable in the Richmond field, because it is difficult and dangerous here, on account of the inferior roof, to remove the last vestiges of coal ; and we are compelled also to retain all the slates and bands, as far as possible, in the pit, to help fill up, although such material is liable to fire. This, however, can be prevented to a great extent, as mentioned below. I am satisfied that the only system of working this thick coal is by cross-cutting (Querbau, ouvrage & travers) or working in benches, as practiced in France (Creusot, Rive de Gier, St. Etienne), in Silesia (Kiinigsgrube), which I have used as far as it is practicable in an old pit, almost torn to pieces by former workings. Modifications may, of course, be needed, even in the same pit, on account of irregularities in the seam. I am also satisfied for economical reasons (on account of the heavy cost for timbering) that pits here ought to be worked upwards, even if it requires a longer period of time to win the coal, and a greater outlay of capital to commence with. The various saddle-shaped " troubles " making natural minor basins in the main basin aid in the execution of this plan. A pit worked once ought to be worked out clean, given up, and dammed off forever. If sections of proper height are assumed, according to the required amount of production for a certain period of time, they ought to be worked out and filled in as much as possible, dammed off, and ultimately allowed to fill up with water, in order to protect the upper works in future from fire in the gob below. This I consider indispensable, because we may not be able profitably to fill in all the ground. To do so we have to use the waste of the mine, although it is liable to fire in time. In using this stuff, it ought to be surrounded by walls of rock not liable to take fire, laid firmly in clay, the gob being in the middle, and firmly covered and packed with clay on top. In

By Allison de Sá Barreto Ferreira

O objetivo deste trabalho consiste em estudar o perfil térmico da carcaça metálica inferior do Forno Elétrico a Arco (FEA) durante o processo de produção de aço, sugerindo adição de aletas na geometria a fim de obter maior troca de calor e diminuição na temperatura de trabalho da carcaça metálica inferior do FEA. Assim, analisou-se a influência do ciclo térmico do processo por meio de acompanhamento termográfico e simulações computacionais via Método de Elementos Finitos. Posto isto, as modificações propostas, depois de testadas e analisadas por meio de um acompanhamento termográfico, denotaram eficiência de tal maneira que resultou em uma diminuição de aproximadamente 60ºC da temperatura na carcaça metálica inferior do FEA.

Oct 30, 2017

By Pablo dos Santos Pina

O alto custo do coque na produção de zinco no Forno Waelz da Votorantim Metais Zinco, em Juiz de Fora, ensejou a realização de testes em parceria com o SENAI CIMATEC para utilização de combustíveis alternativos na Planta Piloto, com o objetivo de mapear a viabilidade técnica e financeira para utilização na Planta Industrial. Ao longo dos testes foram utilizados: cavaco de eucalipto, chip de pneu e moinha de carvão vegetal. Os testes foram realizados com sucesso, apresentando oportunidades de substituição do coque usado atualmente por combustíveis alternativos, com potencial de ganho financeiro para VMZ JF. Este potencial precisa ser validado em testes em escala industrial.

Aug 17, 2017

By Leonardo de Oliveira Turani

A energia eólica, fonte de energia renovável e de baixo impacto ambiental, vem crescendo rapidamente na última década, em especial no Brasil. A conversão da energia cinética dos ventos em energia elétrica é realizada por aerogeradores, que são acopladas em torres, que na sua maioria são constituídas de anéis sobrepostos de aço, os quais são fabricados e montados com o emprego de várias etapas de soldagem. Em função disso, o conhecimento da soldabilidade dos aços estruturais é um fator importante para indústria eólica, dando subsídios para a elaboração de procedimentos que permitam a redução dos custos de soldagem e a seleção adequada dos aços empregados. Este trabalho objetivou a avaliação da soldabilidade do aço estrutural EN 10025-4 S355M através de ensaios mecânicos e metalográficos de juntas soldadas pelo processo de arco submerso (SAW) em duas diferentes técnicas: Single Arc e Tandem Arc. Os resultados mostraram que o aço S355M apresentou excelente soldabilidade, com destaque para o processo SAW Tandem Arc, o que possibilita a maior exploração desta técnica como uma excelente alternativa para a redução do tempo de soldagem durante a fabricação de torres eólicas.

Aug 8, 2018