Search Documents

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By Xumeng Chen, Yongjun Peng, Dee Bradshaw

Regrinding rougher flotation concentrates has become a common practice when processing low grade and complex ores. It not only reduces the particle size and improves mineral liberation but also modifies particle surfaces and pulp chemistry due to the strong electrochemical reactions taking place during regrinding. Therefore, the floatability of minerals in the subsequent cleaner flotation is influenced by the regrinding conditions. This paper presents the effect of regrinding conditions on the mineral floatability from both industrial studies in the plant and fundamental studies in the laboratory. Different regrinding conditions were considered, including grinding media, the electrochemical properties of minerals, pulp chemistry (pH, Eh, DO), and breakage mechanisms in tumbling and stirred mills. Results indicate that the selection of regrinding conditions and mill types should not only depend on grinding energy efficiency and liberation but also depend on the surface properties and pulp chemistry produced for effective mineral flotation and separation at the cleaner stage.

Jan 1, 2014

By B. J. Zhang

Conventional spirals are capable of providing excellent clean coal recovery, although at a relatively high ash content. Compound spirals, which provide two stages of spiral cleaning in a single taller unit, have been commercialized in recent years to improve upon the cleaning performance obtained from conventional spirals. The present study aimed at optimizing the performance obtained from a compound spiral for cleaning especially high sulfur fine and ultrafine coal. Industrial-scale spiral units were utilized for this study in a pilot-scale facility at the Illinois Coal Development Park. A statistically designed experimental program was conducted to optimize ash and sulfur cleaning performance of the compound spiral. It was found that significant cleaning of ultrafine coal (i.e., 150 microns × 45 microns and even 45 microns × 25 microns size coal) is achievable with the compound spiral. However, operating conditions for cleaning finer coal fractions (-150 microns size coal) have to be significantly different from those used to clean coarser coal fractions (+150 microns size coal). The sulfur rejection trends were different from ash separation efficiency trends in all size fractions except 45 microns × 25 microns. The probable error (Ep) and effective specific gravity of separation (SG50c) determined for the compound spiral cleaning of the overall particle size were as low as 0.07 and 1.62, respectively. However, the bypass of a small percentage of clean coal to the tailings stream of the compound spiral, may need further adjustment of the key process parameters.

Jan 1, 2014

By P. Reyes

The start up and operational optimization of the No. 3 Oxygen Plant at the Caletones Copper Smelter of the Codelco - Chile El Teniente Division is summarized. In addition, the economic impact of such optimization on the production cost of oxygen and others aspects associated to the operational robustness as well is detailed.

Jan 1, 2007

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015

By A. G. Journel, CH. Huijbregts

"Centre de Morphologie MathématiqueSpecial problems arise in the evaluation of lateritic-type orebodies (Ni-Co, bauxite) or, more generally, orebodies affected by surface weathering. In this type of orebody, the vertical grade distribution shows, from the hangingwall downwards, a systematic increase followed sometimes by a certain decrease, or vice-versa. These trends appear together with irregular variations from one drill bole to the other.The problem is to characterize a vertical structure that is representative not only of the drill hole but of an entire panel or zone of influence, in order to define mineable thicknesses for given cut-off grades. The vertical grade distribution observed on the drillhole is replaced by a new curve, called 'derive' (drift), which is computed by 'universal kriging'.Once the vertical study is completed, new 'service-variables' are defined in the horizontal plane, such as mineable thickness and the corresponding average grade, economical functions (combination of the grades of several minerals). The local and global estimation of these variables can then be performed by a simple bi-dimensional kriging plan. The global estimation is summed up by several tonnage-cut-off grade curves.The practical valuation according to the above scheme of a New Caledonian lateritic nickel orebody is presented."

Jan 1, 2014

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By J. R. Iwinski

Escanaba, Michigan, is located on the South¬ern shore of the Upper Peninsula on a sheltered area of Lake Michigan called Little Bay de Noquet. The Chicago and North Western Transportation Company has operated a rail-to-ship ore transfer facility at this location for well over 100-years. It is the only terminal of its type on Take Michigan and thus can offer a longer navigation season to lower lake markets than other upper lake ports. It all started in 1864 when the Peninsula Railroad of Michigan, now a part of the C&NW, completed a 100 km rail line from Little Bay de Noquet to the Jackson Mines at Negnauee, Michigan. During that first year of operation approximately 31 000t of ore were loaded onto ships at Escanaba from what was then called the Merchants Dock. By 1871 demand had already exceeded capacity and it was necessary to build a larger dock, which in turn was replaced with a still larger pocket dock in 1903. There are no plans or records available to indicate how the ore was handled from rail to ship prior to the construction of the pocket dock.

Jan 1, 1981

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By J M. F Clout

The Roy Hill Project is an independent integrated port, rail and mine development in the Pilbara region of Western Australia. The bankable feasibility study for the project was completed in January 2011 by Roy Hill Holdings Pty Ltd, a wholly owned subsidiary of Hancock Prospecting Pty Ltd. The Project will deliver 55 Mt/a of premium quality iron ore to a rapidly growing market with a mine life of over 27 years. This study is based on exploiting a 1.2 Bt bedded resource of microplaty haematite-rich Marra Mamba, from which 562 Mt of reserves has been delineated to date. A further 1.1 Bt resource of detritals and low grade bedded is proposed to be mined once the bedded high grade resource is depleted. Roy Hill lump and fi ne ore products will compete strongly with other Pilbara products. As a low cost producer, Roy Hill is on track to capture four per cent of the global seaborne traded iron ore market. The project decision to proceed is targeted for Q2 2011 to enable first ore on ship by Q2 2014.

Jul 11, 2011

By Stanley M. Walker

Safety consciousness is not a constant for which a specific value can be assigned, but is a variable, which is frequently intangible. Its evaluation is not simple. We all know that safety consciousness is the most potent factor in the prevention of accidents. Safety consciousness may be defined as awareness of hazard and alertness to danger, which controls every action of an individual through his desire to remain alive and uninjured.

Jan 1, 1951

By B E. De Gee, N Viviers, A Naidoo

In 2013 the Mopani Copper Mine Mufulira plant in Zambia embarked on a project that was aimed at improving concentrator recoveries. The project commenced with the automation of the milling and flotation circuits. This involved the installation of new instrumentation, namely measurement devices and actuators, and the connection of these to new programmable logic controllers (PLCs).The infrastructure changes were followed by the implementation of basic proportional-integral-derivative (PID) controllers on the PLCs. Supervisory control and data acquisition (SCADA) interfaces were also implemented to allow for switching between controller modes, inputting of setpoint variables and to provide a visual display for process monitoring. The final phase of the project involved the installation and commissioning of advanced process control (APC) solutions on the milling and flotation circuits. This work was carried out by Mintek over 21 on-site days. The APC solutions included the MillStar and FloatStar suites of advanced controllers.The MillStar control suite focused on stabilising the mill feed and mill discharge on the two primary mills as well as the flotation circuit feed. Mintek’s CyLas instruments, which provide a measurement of the hydrocyclone underflow angle, were also installed. The measurements were incorporated into the discharge stabilisation control on both milling circuits. The FloatStar level stabiliser controller provided flotation cell pulp level control on fourteen cells, including two columns.Performance tests showed that the Mintek APC system stabilised the mill feed and mill discharge while ensuring the process remained within operational constraints. The MillStar control system utilised the CyLas instrument to prevent roping on the hydrocyclone underflow. This was not always achieved under normal operation. Additionally, the flotation section was stabilised as a result of improved level control by the FloatStar control system.Performance comparisons showed that the Mintek control system improved the operation of the milling and flotation circuits resulting in a greater copper recovery.CITATION:Naidoo, A, De Gee, B E and Viviers, N, 2014. Implementation of an advanced milling and flotation control system at Mopani Mufulira copper mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J. R. Odekirk

The nature of mineral distributions and locking characteristics in mill products are important factors in understanding mill performance. Such data are obtained by microscopic point counting methods. Reduction 'of point-count data from volume to weight percentages, and reduction of data for each size fraction back to a head sample requires lengthy hand calculations. The use of computer processing for such data reduction results in obtaining information on a realistic time basis. An example of computer processed point-count data is presented.

Jan 1, 1981

The past four years since the 2008 MINExpo have been a roller coaster ride for the mining industry, with highs and lows and everything in between. One of the natural consequences of this uncertainty has been a number of significant consolidations and mergers, and this trend has trickled down into the crushing industry. And while there have been some significant changes to this sector of the mining industry, many of the big players have weathered the storm. The following is a look at some of the mineral processing companies that will be at MINExpo. McLanahan Corp. McLanahan Corp. is an example of the changes in the sector. The crushing and grinding stalwart acquired Universal Engineering, expanding its traditional focus on soft mineral crushing to hard rock crushing. At MINExpo, it will be showing off three new pieces of equipment, the LabMill Crusher, the Rocker Tooth Crusher and the Recessed Filter Press.

Jan 1, 2012

By J Herd, J Rowe, M Cutbush, d F. Aziz

WearApp provides expertise for assessing the degradation of removable screening media panels on vibrating screens right in a user’s pocket. Through the WearApp application, users can simply take a picture of a panel using their mobile, enter some basic information and have the application assess the wear to provide a recommendation for whether the panel needs to be replaced. Where traditional mechanisms for assessing panel wear only measure a few points across the panel face and rely on having personnel with specialised knowledge available to perform the assessment, WearApp uses deep learning models to analyse the entire panel face and support the user to make an informed decision. The application works through analysing a panel image and using a model to automatically detect the corners of the panel. Given the known dimensions of the panel, this enables the application to calibrate the pixel size against a known reference. A second set of models then detect the apertures and measure their dimensions. With the aperture dimensions defined the application assesses the wear of the panel through referencing a stored 3D model of the aperture. Finally, the data from each aperture is collated and the wear of the entire panel face defined. Since WearApp performs measurement of the entire panel face, it also allows the user to perform a more detailed analysis of the panel’s wear profile. Where typically, the panel wear is only measured in a few locations, WearApp’s analysis enables users to visualise the panel wear across the entire panel face, identifying areas of high wear that could be leading to premature panel replacement. Additionally, because the entire panel face is measured the change in screening efficiency can be calculated accurately for the worn panel, even taking into account the impact of aperture pegging by small rocks.

Sep 1, 2024

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014

Pike River Coal Limited is in the process of developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction. The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park.   As such, the major restriction to planned extraction is protection of: +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2006