Search Documents

By J. E. Chilton

Interim performance specifications are presented for carbon monoxide, methane, and air velocity transducers used in the Bureau of Mines intrinsically safe mine monitoring system. These specifications give quantitative values or qualitative descriptions of the transducers, including environmental parameters and monitoring system measurement and maintenance requirements as recommended by the Bureau of Mines. Commercially available transducer modules and prototype modules are listed together with selected characteristics.

Jan 1, 1983

By R. D. Haynes

Coal, gas, and oil in many geological formations of the Eastern United States are intimately associated but have traditionally been recovered independently of each other. Oil and gas wells, however, are often spaced sufficiently close to cause the subsequent loss of up to 50 percent of the recoverable coal in the form of pillars or barriers left for mine safety purposes. A long-range planning technique was devised for exploiting oil and gas wells simultaneously with the mining of coal to recover the maximum fuel potential of the formations. Planned plugging of oil and gas wells, determined partly from production predictions via decline curve analysis, is coordinated with a mine development plan to achieve maximum coal recovery and reduce overall production losses of gas and oil due to plugging of the wells.

Jan 1, 1973

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By Adelson Dias de Sousa

O objetivo deste trabalho é mostrar os estudos para remoção de sulfatos no efluentes industrial da Votorantim Metais Zinco, unidade Três Marias.Um dos maiores desafios na indústria que trabalha com meio sulfúrico em seus processos, é a remoção de sulfato de seus efluentes. Neste sentido a Votorantim avaliou vários processos distintos a fim de atingir uma concentração máxima de 250mg/L de sulfatos, dentre eles, precipitação química, redução biológica e resina de troca iônica.Dentre os processos avaliados, o que apresentou os melhores resultados foi a precipitação química através da formação de etringita, composto de fácil separação sólido-líquido, atingindo resultados de concentração de sulfato inferiores a meta máxima de concentração.

Aug 16, 2017

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By Alessandro Pigani

Over the last 25 years the thin slab casting and rolling process has been gaining a major market share in the production of hot rolled strip, progressively eroding the areas previously of exclusive domain of conventional mills. This is mainly thanks to the competitiveness of the process over conventional ones, and to the growing ability of this technology to cover the majority of market niches, well beyond the boundaries of the commodity market. After having significantly contributed to the continuous expansion of this production mode and after an extensive campaign of theoretical research and physical testing in reference plants, Danieli has progressively developed over the years a new generation of thin slab casting and rolling layout, marking a new phase in the evolution of this process. The new step-ahead is epitomized by the name QSP-DUE. This configuration belongs to the Quality Strip Production (QSP) family, which is Danieli’s strip-quality-oriented thin slab based plants. The innovative features of the process are embodied in the acronym DUE, which stands for Danieli Universal Endless (Danieli patented technology – US patent n. 8087449, January 3rd, 2012). What makes this new concept different is the ability of “universal” rolling modes thanks to the fact that, now, within one single plant it is possible to perform coil-to-coil, semi-endless and endless rolling modes, making this plant a major technology innovation compared to the previous generation.

Aug 16, 2017

By G Fergus, M Hart, S W. Weeks

Rio Tinto Alcan has undertaken feasibility level assessments into the expansion of its bauxite mining operation in an area south of the Embley River in far north Queensland. The project has the potential to extend their Weipa operations by approximately 40 years.The construction and operation of two additional mineral ore processing plants are proposed for the South of Embley project. Golder Associates was engaged to develop and conduct modelling assessments of potential sources of water supply required by mineral ore processing.Two models were developed using GoldSim: a dam yield model and a water balance model. GoldSim is a graphical object-oriented modelling environment with a capacity to carry out dynamic probabilistic simulations. Originally developed by Golder, GoldSim has been applied successfully in a decision support role to a range of mine water management operations.The dam yield model was used to provide estimates of reliability and volume of annual water supply of several potential surface water dams. This information was then used to determine a hierarchy of water supply options for processing plant operations. The water balance model dynamically simulated the water demands of the two production plants and the consequential response in water supply, with respect to the timing and discharges provided by the various source options.Use of the model provided a preliminary operational tool to assist with water supply management decisions. Water quality issues required a blending of water from separate sources and attention paid to scheduling to ensure water supply through the dry season. The model also helped identify risks to water supply in the event of underperformance of one or more water supply sources. This allowed the operational rules to be refined to minimise those risks.The dynamic and stochastic modelling approach provided a method for identification of water supply issues susceptible to seasonal climate variability.CITATION:Weeks, S W, Hart, M and Fergus, G, 2013. A dynamic evaluation of water supply security susceptible to climate seasonality, in Proceedings Water in Mining 2013, pp 197-208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Christian O’Keefe, Alex Van der Spek

"Evaluation of inequalities of the partial sums defining cumulative grade and recovery prove that cumulative grade has an upper bound not dependent on the bank number and cumulative recovery possesses an upper bound proportional to the bank number. This explains one observed characteristic of cumulative grade versus cumulative recovery curves. The existence of such maxima combined with the observed shape of cumulative grade-recovery curves leads us to postulate that these curves can be well described by rectangular hyperbolae. Rectangular hyperbolae are characterized by asymptotes at right angles to each other. It is proven that this property can be used to derive an equation for the cumulative mass flow of the concentrate in terms of the asymptotic values of cumulative grade and cumulative recovery. Fitting hyperbolae to experimental cumulative grade cumulative recovery plant data then results in estimates of the maximum grade, the maximum recovery and a constant which may be taken as a performance coefficient of a row. Normalization of the cumulative grade and the cumulative recovery by their respective maxima gives rise to a graphical representation that can be used to evaluate the operating performance of a row of floatation bank cells. The normalization procedure removes the bias that is introduced by inevitable variation in mass flow of the feed and variation in feed mineralogy or feed particle size distribution. Reduction of the normalized data collapses all cumulative grade-recovery data onto one and the same curve. This removes the differences caused by the variation in row performance. The reduced cumulative grade-recovery data scatters around a common hyperbola. This can be used to gauge the validity of the assumptions made. Normalized cumulative mass pull is determined from the fitted values of the maximum recovery and maximum grade. This may serve as an alternative performance indicator of the floatation row."

Jan 1, 2014

This Bureau of Mines report reviews the development of the world potash industry. The trends leading to the present market situation of oversupply arid low prices, which threaten; the domestic potash industry, are presented and analyzed. Because the major threat to the domestic industry comes from Canadian imports, the report focuses on the comparative economics of United States and Canadian production. The study resulted in these major conclusions: 1. Balance of world supply and demand is foreseeable in 1975, but it could be delayed by planned expansion. 2. Balance of U.S. supply and demand could occur as early as 1974-75 or as late as 1981. 3. Nearly all U. S. production capacity vis-a-vis Canadian competition is now uneconomic. Prices cover out-of -pocket costs for only 30 percent of U.S. production. 4. U.S. producers will be undersold by Canadians in 60 to 90 percent of the U.S. market. Canadians also will have the edge over United States and European producers in export markets. 5. U.S. firms have invested in 60 percent of the planned 1971 Canadian production, and they have large holdings in Saskatchewan. 6. The decline in the U.S. potash industry probably reduced personal income in Carlsbad, Eddy County, N. Mex, the chief potash-producing area in the United States, about $21.5 million between 1966 and 1969.

Jan 1, 1970

By CHARLES E. W.

I. LOCATION. THE Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low ridge of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. CLIMATE AND VEGETATION. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera-ture is generally from 60° to 70° F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100° F. in the day-time, while 115° F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1906

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By Mario E. Rossi

Often geometallurgical models are prepared at various project stages from very few data and are assumed to be representative of very large tonnages. These may include recovery models; crushing and grinding parameters and models; models of concentrate grades; models of acid consumption; etc. These models commonly do not carry a measure of uncertainty or variability, and are taken at face value at the time of design and planning. This paper proposes a proactive approach to modelling variability, providing uncertainty estimates and thus allowing for risk analysis and mitigation of geometallurgical models. The variability model is built up by understanding the limitations of the pillars of a geometallurgical model: data uncertainty; geologic model uncertainty; domain definition uncertainty; and parameter estimation uncertainty. Of these factors, typically domain definition is the most significant contributor to geometallurgical model variability. First, the fundamental supports for these models are briefly discussed, with domain definition emphasized. Second, two methods for uncertainty modelling are proposed. The first, more applicable to conceptual or early-stage projects, is a simpler and more expedient alternative that provides initial assessments of variability. This is intended to aid management in decision-making related to budgeting, including further sampling and testing. The second, a block-by-block approach that allows a detailed assessment of risk for specific designs and mine plans, thus providing further opportunities for mitigation. In the example provided, emphasis is placed in communicating this variability to both management and technical personnel in the form of “measured-indicated-inferred” indicators and also block-by-block confidence intervals.

Jun 25, 2023

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By B. Markovic

Performance of mineral filler particles in ceramic applications can be enhanced markedly by adsorbing polymers of optimum molecular structure and dosage. In a recent work by Chen and Somasundaran (1997), a novel scheme of controlled polymer adsorption was used to produce nanocomposites of unique core-shell designs. Towards this purpose, adsorption and desorption behavior of selected polyacrylic acids (PAA) on three minerals; alumina, titania, and silicon carbide, was examined as a function of relevant parameters. Adsorption of P AA was found to depend on polymer molecular weight, pH, as well as solids loading. Specifically, the adsorption density was found to increase with increase in polymer molecular weight for non-porous alumina while it was found to decrease in the case of porous alumina. This is attributed to the inaccessibility of the pores to the larger polymers. An unexpected finding was the change in the adsorption density of PAA with solids loadings. PAA adsorbs on silicon carbide only at low pH values when the particles have very low surface charge suggesting that the adsorption in this case is controlled by electrostatic forces. Using polyacrylic acid as bridging agent between the alumina fillers (core) and nanosize alumina or titania particles (shells), controlled layer by layer deposition of nanoparticle on the core particle surface could be obtained.

Jan 1, 1997

By Nicolas Moscoso, Gerald Verbeek, Marcel Bielefeld, Rob van Dorp

Upon recently, most offshore foundations were based on a number of driven piles that were installed with an impact hammer. With the increase in offshore windfarms two major developments have occurred: the shift from jackets to monopiles, leading to increase of the diameter of the foundation piles, and a shift from impact hammers to vibro hammers. As the use of vibratory hammers is becoming more and more common practice, the need for accurate vibro-driving simulation software has increased, which requires that the soil modelling is enhanced to address soil fatigue during pile driving and to predict reliably the soil behavior and resistance during pile driving. In addition pile driving monitoring, which is routine for piles driven with an impact hammer, needs to become common practice. This paper addresses advances in soil modelling that allows more accurate pile driving simulation as well as the application of Vibro Driving Analysis (VDA) or Monitoring (VDM) to validate the simulation results. This is illustrated by a case study of the test pile for the Delft Offshore Turbine project, a 28 m long monopile with a diameter of 4 m that was driven 15 m into dense sand layers using a vibro hammer. After some 6 months the pile was extracted, and pile driving simulations and VDA were done both for the installation and extraction phase. 1. INTRODUCTION At the end of 2017, the total worldwide offshore wind power capacity was 18.8 GW [1]. The vast majority of offshore wind farms are currently in Northern Europe, which together account for over two thirds of the total offshore wind power installed worldwide, followed by East Asia, while developments in North America are still in very early stages.

Jan 1, 2019

By P. C. Benedict

Introduction and Summary The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, district of Thunder Bay, Ontario. Production started in March, 1934, and terminated in September, 1941. During this period, the mill treated 425,866 tons of ore, from which 153,103 ounces of gold were recovered. The lowest level from which ore was mined was the 1900, but considerable drifting was performed on the 2075 level and 800 feet on the 2415, the deepest level. The following description of the geology of the mine is recorded by the senior author but is based on the observations and complementary mapping of both authors. The vein strikes about N.72°E. and has an average dip of 80°S. (Figure 1). In stoped sections, the quartz averaged about two feet wide. On the 1725 level it was drifted on continuously for more than 7,000 feet, but in the mine as a whole practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section but not much beyond its limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth. It may be generalized, from top to bottom, as light grey to dark grey to brownish. The brownish quartz first appeared near the bottom of the ore.

Jan 1, 1947

By Jay Nopola, Christopher Johnson, Matthew Minnick, Erik Hemstad, Erik Walega

Mining data collection, storage, and interpretation methods have progressively changed over time. Data collection, for the most part, has transitioned from handwritten notes and logs based on manual gauge readings to real-time data streaming through instrumentation capable of directly communicating with site-based data historians or cloud storage. Data collection and storage have had to adjust commensurately with the volume of data, leading to more complex database architecture. Geoscience interpretation methods have also changed; however, the first goals of modeling and understandings from first principles remain the same and are typically deeply rooted in historical academic work. Machine learning methods are becoming more common, available, and implemented by industry and practitioners. Despite the wide accessibility of machine learning methods, the population of geoscience subject matter experts in the underlying theory of this analysis type is limited. This form of analysis, therefore, must be conducted carefully and in conjunction with subject matter experts, on both machine learning theory and the field it is being applied to. This paper aims to provide background history on data analytics and machine learning, current methods and practices, and high-level geoscience case study examples, as well as take aways regarding the mining industry, potential pitfalls specific to geosciences, and possible perspectives on the direction of artificial intelligence in the future.

Jun 25, 2023

By G. R. Harrod

Effective mine operation demands that the right people have the right information at the right time. Caterpillar's Mining and Earthmoving Technology System (METS) meets this demand by providing "real-time" information transfer between the mine offices and machines equipped with the Caterpillar Computer Aided Earthmoving System (CAES). Transfers of mine plans from the mine planning software to CAES-equipped machines give operators access to current mine plans within minutes of their creation. Additionally, office personnel have access to a current digital terrain model (DTM) of the mine site as it is updated in "real-time" by CAES-equipped machines. METS provides mine personnel in operations, planning, and management the information they need when they need it.

Jan 1, 1998

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011