Search Documents

By R. W. Hiteshue, C. O. Hawk, H. H. Ginsberg, M. D. Schlesinger

The Bureau of Mines studied single - step catalytic vapor - phase hydrogenation of oils derived from coal and oil shale . Treatment of middle oil , from hydrogenation of bituminous coal , gave good yields of gasoline with a German - made molybdenum- zinc - chromium catalyst . The Bureau also achieved good results with duplicates of this catalyst made from domestic raw materials . In one set of experiments with the German catalyst , 38 to 52 wt pct of feed was converted to gasoline . The total liquid product was 91 to 98 wt pct of the feed . Not all this gasoline can be claimed as production , however , because about 20 pct of the feed was in the gasoline range , and part of it undoubtedly survived the hydrocracking treatment . Hydrogenation of crude shale oil in the presence of cobalt molybdate catalyst produced a total liquid product of 89 wt pct of feed . The hydrogenation converted 27 wt pct of feed to gasoline and 44 wt pct of feed to diesel fuel . The remaining liquid product , 18 wt pct of feed , was residue boiling above diesel fuel . The gasoline was of poor quality , with an octane number of 39.1 . The overall product seemed a suitable feed stock for a conventional refining operation . Coker distillate hydrogenation , using a cobalt molybdate catalyst , gave a total liquid product of 97 vol pct of feed ; of this product 60 vol pct was jet fuel and 40 vol pct was diesel fuel . High nitrogen and sulfur in all three of these raw materials severely poison the usual refining catalysts . Thus , the common objective in these

Jan 1, 1964

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By Lloyd A. Morley

This eight-chapter document is the second volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. Building upon Volume I, the subject of protective equipment and relaying starts Volume II, first as an introduction in Chapter 8, then by a treatment of device selection in Chapter 9. Chapter 10 continues system protection in terms of transients and overvoltages. Chapter 11 describes the design of major power equipment, including power centers, switchhouses, and substations. Solid-state applications in mining are given in Chapter 12, and batteries and battery charging are discussed in Chapter 13. Chapter 14 covers electrical-equipment in hazardous locations of mining operations. The report concludes with Chapter 15, a discussion of electrical maintenance as well as some specific mine electrical problems. Information on surface and underground use is included in all these chapters. An index finishes the documentation and is cross-referenced to both report volumes.

Jan 1, 1982

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

A key driver to the success of a tunnelling project (the project) is the management of hydrogeological risk. The hydrogeological risk, if not managed, may cause significant impacts on the overall performance of the project. Impacts may include groundwater quality impairment due to contaminant transport and acid drainage from disturbed geology to groundwater, and groundwater lowering. The groundwater lowering and quality impairment may cause tunnel failure, with consequences such as injury to humans, as well as reduced property and environmental values, potentially costing millions of dollars to sponsors of the project. Depending on the nature of the contaminants and level of hydraulic connection of bedrock fracture along the length of tunnel, the contaminant transport may reduce structural strength of the tunnel due to corrosive action of contaminants such as acid drainage. The groundwater lowering can lead to varying degrees of ground settlement, posing threat of tunnel collapse. The management of hydrogeological risk includes:detection of potential pathways for contaminants into and around the tunnel,identification of factors responsible for the lowering of groundwater, and development of strategic measures to control groundwater lowering and contaminant transport. The paper presents an in-house hydrogeological risk management model named Vedanta-THRM (tunnel hydrogeological risk management). The model uses Risk Management Standard AS/NZS 4360:2004 (Standards Australia, 2004), Pressure State Response framework developed by Organisation of Economic Cooperation and Development, and Interaction Matrices. The Vedanta-THRM identifies important characteristics, processes and events of potential hydrogeological risk and develops control measures for managing hydrogeological risk throughout the life cycle of the project. The Vedanta-THRM was applied for a project in the early stages of planning and found to be useful in assessing, evaluating and reducing the hydrogeological risk in a managed approach that potentially increased the performance of the project. The application results also provided management options for use by project sponsors and insurance industry, which included tunnel risk financing options and options for equity investors to choose among various returns under different tunnel credit ratings.

Jan 1, 2008

In coal mining, geophysical techniques have an established application in determining the location of seam boundaries ahead of the face so that underground mines can be planned to avoid any geological structures that might disrupt production. Geophysics can also be used in geotechnical studies to determine the in situ properties of the rock mass and the response of the rock mass to the mining. The use of geophysical logs and microseismic monitoring in these geotechnical applications are discussed in this paper.

Jan 1, 2002

By Will B. Jamison

An ignition detection and suppression system was developed under the scope of this contract. The objective of this machine mounted system was to detect flames caused by frictional sparking from the cutting bits of a continuous mining machine and to suppress it with sufficient speed to prevent the development of an explosion, and to keep the flame from harming the machine operator.

Jan 1, 1976

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

By K. K. Kelley

The first bulletin (245)3 in this series, which appeared in 1932, summarized the entropy values then available for the elements and inorganic compounds, results being listed for some 150 substances. In the interim advances in the realms of spectroscopy applicable to the determination of thermodynamic properties and in the development of methods of calculation therefrom have added many highly accurate values. Moreover, through the efforts of Prof. W. M. Latimer (286) and his coworkers, satisfactory entropy values are now available for all but a few of the common inorganic ions in aqueous solution. At the same time rapid progress has continued in the study of low-temperature heat capacities in several laboratories, In addition, compilation and correlation of data pertaining to vapor pressures (247), thermodynamic properties of carbonates (258), thermodynamic properties of sulfur and its inorganic compounds (250), and the thermodynamic properties of metal carbides and nitrides (251), which were published as members of this series, have yielded many values. As a result, over 500 usable entropy values for inorganic substances may now be tabulated. This bulletin originally was planned as a second revision of the first member of this series, the first revision (249) having appeared in 1936; however, because of requests for the explanatory section of the first bulletin from those teaching thermodynamics, it was decided to com¬bine the information in the first bulletin and its revision with the data that have appeared since 1935 and to repeat the explanatory material in somewhat more detail. The purpose of this bulletin is therefore to give the available values of the entropies at 298.1° K. of the elements and inorganic compounds, together with enough explanation of the methods employed in calculating entropies to make the results comprehensible.

Jan 1, 1941

By Mark Khinkis, Huajun Yuan, Mark Zak, Yaroslav Chudnovsky, Aleksandr Kozlov

"An afterburner for green petroleum coke calcination in electrothermal fluidized bed was designed, fabricated, installed, and tested on a pilot fluidized bed calcination furnace. The experimental set-up comprised a combustion chamber, in which fine particles and volatiles of the furnace off-gas were fully combusted, and a cooler equipped to calculate the related heat recovery and losses. Off-gas composition was analyzed to evaluate the combustion process. The energy balance confirmed the potential to recover a large part of the heat value of volatiles and fme particles from the GPC. Potential future applications of the results are discussed.IntroductionGreen petroleum coke (GPC) is an oil refining byproduct that can be used directly as solid fuel or as feedstock for the production of calcined petroleum coke [1-2]. GPC contains a high amount of volatiles and sulfur. With coke calcination, the GPC is heated to remove the volatiles and sulfur in the calciner off-gas to produce purified calcined coke, which is used in the production of graphite, electrodes, metal carburizers, and other carbon products. Currently, more than 80% of calcined coke is produced in rotary kilns or rotary hearth furnaces. These technologies provide partial heat utilization of the calcined coke to increase efficiency of the calcination process, but they also share some operating disadvantages [3]. On the other hand, coke calcination in an electrothermal fluidized bed opens up a number of potential benefits for the production enhancement while reducing the capital and operating costs.The increased usage of heavy crude oil in recent years has resulted higher sulfur content in green coke produced from oil refinery process, which requires a significant increase in the calcinations temperature and residence time [ 4]. The calorific value of the process off-gas is quite substantial and can be effectively utilized for combined heat and power (CHP) production to complement the energy demand. Waste heat recovered from the product cooling could also contribute to the overall economics of the calcination process. Preliminary estimates indicated the decrease in energy consumption by 35-50% as well as a proportional decrease in greenhouse gas emissions. So, efficiency improvement of the coke calcinations systems is attracting close attention of the researchers and engineers throughout the world."

Jan 1, 2014

By Paul Worsey, Seokbin Lim

There are two major types of shaped charges, conical and linear (Ref 1, 2). Conical shaped charges are used to perforate targets and are mainly used by the military as anti armor weapons and by the oil industry for oil well perforation. In contrast, linear shaped charges are primarily used to cut metal in the demolition industry with other uses including separating devices in the space industry. There is a large amount of material published on conical shaped charges because of the high level of defense industry research and funding, however in stark contrast there is very little published on linear shaped charges.

Jan 1, 2003

By Y. P. Chugh

Additional field evaluations of a modified continuous miner using a new spray system and modified scrubbers have been conducted by the authors. In this demonstration, a comprehensive package for dust control on a continuous miner which included previously developed modifications to the scrubber, scrubber intakes and the innovative chassis spray system was demonstrated. Side-by-side comparisons of the modified miner and regular miner indicated that the miner operator with the modified miner was exposed to 62% less respirable dust. Ram car operators with the modified miner had 38% less respirable dust exposure and the return air on the modified miner had 19% less respirable dust. The mining conditions during side-by-side testing were very comparable. These results support the findings of the modified spray system studies conducted earlier at different mines in Illinois on four occasions and the modified scrubber system field evaluation studies.

Jan 1, 2009

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By Keith S. McIntosh

The fire assay process for the quantitative recovery of platinum group elements (PGE?s) prior to subsequent analysis traditionally is a time-consuming process. Samples derive from various ore types and contain PGE?s at the ppm or ppb levels, making concentration of the elements mandatory before assaying. Traditionally sample turn-around times are of the order of 24 hours. The whole sequence of sample preparation, fire assay and subsequent analysis of PGE?s have been automated by Anglo Platinum. Some of the major challenges on the road to automation will be discussed and the novel solutions that were implemented. The engineered solution included robotic automation of the whole sequence, from sample preparation, up to the final element by element assay. The final system allowed for rapid (less than one hour) and accurate analysis of PGE?s even in streams containing very low levels, such as flotation tailing streams and drill core samples.

Jan 1, 2006

When we are beset with the economic problems the world faces today, we are always inclined to look at the shorter term future. Today I would like to take a long-term view of our industry, project historical demands for our products into the future and discuss opportunities for our members. Perhaps we could firstly look at the long-term demand trends for our metals. If I tend to use non ferrous metals as a basis for my figures it is because this data is more readily available to me. I am sure that most other products of our industry show similar trends.

Jan 1, 1992