Search Documents

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

By Michael G. Nelson, Dot J. Helm, Edmond C. Jr. Packee

Under a Section 319 Water Quality grant from the U. S. Environmental Protection Agency, a working group of government agencies, mining industry representatives, and University of Alaska researchers undertook reclamation of an abandoned mine site on Birch Creek, near mile 101 of the Steese Highway. Stream hydrology, water quality, and the extent and nature of natural revegetation, were measured before the site was then recontoured to decrease the bedload deposition and bank erosion of the streams. Methods for stabilization of streams and rivers appear to have much in common with those for locations further south, but are subject to complications unique to the North, such as the formation of aufeiss, and to a lack of accurate climatological data. Natural revegetation appears to be possible for most northern placer mine sites. However, it may take place more slowly than required by public perception. Preliminary data indicate a surprising lack of nutrients in the floodplains of mined areas. Natural revegetation may be enhanced by selective planting of grasses and willows, which will contribute variously to soil quality, bank stabilization, and short-term appearance. Monitoring of hydrologic and water quality data, and of natural and artificially placed vegetation will continue at the .Birch Creek site through the summer of 1995,

Jan 1, 1995

By John C. Machisak

Injury data and experience, with related employment statistics, at coal mines in the United States for 1959 are presented in this publication under the following general sections: (A) General injury experience: Tables 1 to 6: Current data on number of injuries degree of injury, frequency and severity rates, average severity, and related employment and production data by work location. (B) Selected injury experience: Tables 7 to 38: Current data on principal agencies of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines.

Jan 1, 1961

By Sie A

After completing a feasibility study in 1987, Niugini Mining Limited (NML) obtained five Gold Mining Leases within PA 632, covering the Mount Victor and Clarkes Ridge gold deposits. Reserves prior to mining were 260 000t at 3.63g/t Au for Mount Victor and 40 000t at 2.8g/t Au for Clarkes Ridge. Ore was mined from the two deposits by NML from November 1987 to January 1990. A total of 645kg of gold and 346kg of silver were produced from 198 000 tonnes of ore pro- cessed. Mining and milling operations ceased in February 1990. Since then, there has been significant progress in rehabilitating and revegetating the site. Plant and workshop facilities have been dismantled and removed from site, exposed parts of the pit have been landscaped and replanted, tailings water has been neutralised and discharged, and the dam filled. All remaining personnel and equipment left the site in November 1990. It is envisaged that the replanted areas will be rapidly revegetated, leaving little evidence of mining. Niugini Mining did not recoup the initial investment for Mount Victor, but the mine produced a positive cash flow and made a significant' financial contribution to the local communities and Papua New Guinea as a Whole.

Jan 1, 1991

The distribution of tin and iron between slag and metal phases at about 1150°C was studied in pot scale experiments. The distribution coefficient k = (Sn/Fe) In metal X (Fe/Sn) in slag was found to vary from about 300 for metal corresponding to nearly pure tin, to about 100 for metal of about miscibility gap composition (17' 4 per cent Fe). Results conformed reasonably well to a straight line relationship between log k and (l-2NFe), as expected on theoretical grounds, and are consistent with thermodynamic data for the Fe-Sn phase diagram and the reaction Fe + SnO = FeO + Sn.Calculations are presented indicating the feasibility of smelting low-grade tin concentrates in a two-stage counter-current reduction process.

Jan 1, 1966

By R. Heuberger

South Africa?s Mining Industry operates in an uncertain world. The industry is buffeted by problems regarding retrenchments, unemployment, low productivity, rising costs, volatile exchange rates, commodity prices and government regulations. With these uncertainties facing the decision makers, what does applied technology offer the industry?s management? Modelling languages with risk analysis have been available for decades, but in the past their use has been very expensive, requiring large mainframe computers and lots of computer time. Today, PCs and laptops have incredible power, which makes interactive risk analysis affordable and viable for all enterprises, whether small or large. ?What is risk analysis? ?What is Monte Carlo simulation? ?What kinds of computer models need to be created to use risk analysis and Monte Carlo simulation effectively? This paper addresses these questions and illustrates, with a practical example in the mining industry, how risk analysis techniques can be used to support decisions in the climate of uncertainty.

Jan 1, 2005

By Francisco J. Cárdenas

El Proceso Green Mining es una innovación tecnológica para la extracción de metales a partir de los concentrados de minerales sulfurados que los contienen, aplicando procesos y operaciones pirometalúrgicos e hidrometalúrgicos no convencionales. Esta innovación reduce el metal en forma directa logrando su extracción con un solo reactor, a presión atmosférica, con una alta velocidad en la cinética de las reacciones químicas y sin tostación previa.

Sep 1, 2017

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1956 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced. (B) Selected injury experience: Tables 10 to 15: Comparable injury data covering 5- and 10- year periods on the number and degree of severity of injuries and major accident causes.

Jan 1, 1958

That electricity is an important and valuable agent, the limit of whose capacity for utilisation is as yet unknown, is a truism; although enormous advances have been made, the possible developments are yet greater. Mining, along with other industries, shares already to a large extent in the practical utilisation of this agent. Electrical engineers have been employed for several years past in developing and applying electricity to all classes of machinery, and for every purpose where power is required and in no instance, that the writer is aware of, has its use been curtailed in favour of any other agency now known, while extensions are continually made. The first modern electric motor was shown at the Vienna Exhibition of 1873, and it was used to work a pump through a mile length of cable but it was not before 1878, that an electric motor was put into daily commercial use by Messrs. Chretian and Felix to work a beet sugar hoist. This early plant effected a saving of 40 % as compared with hand work.In 1879, the first Electric Railway was constructed for the Berlin Exhibition, and in the same year, Mr. T. A. Edison was running an experimental line at Menlo Park. The first electric line opened for the public, was constructed by Siemens and Halske, in 1881, at Lichtenfelde, and was 11 miles in length.

P&H MinePro Services Canada is supplying Syncrude Canada three more of its model4100BOSS electric mining shovels. The shovels will be delivered during 2003. Syncrude’s oil sands operations already use five P&H shovels. The first 4100BOSS shovel was commissioned at Syncrude’s operation in northern Alberta, Canada in October 2001. The unit loads more than 9 kt/hr (10,000 stph) of unblasted oil sands. Since it began operation, the 4100BOSS has shown a 28% production increase over the four P&H 4100TS shovels also on site.

Jan 1, 2003

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

By Andrew Bamber

Between the early 20th Century and the present, the production of mined copper ore has increased from tens of millions of tonnes per annum to several billion tonnes per annum, an unprecedented increase. Contemporaneously, the average grade of mined copper ore has declined from over 2% to approximately 0.5%. Again, in parallel, the price of copper has increased dramatically to reflect the increasing cost of extracting and beneficiating such large amounts of low-grade ore. Within the period the copper price however exhibited several periods of intense volatility, driven by interrelationships between demand and supply, themselves strongly driven by periodic industry developments in the fields of exploration, ore extraction, mineral processing and extractive metallurgy. It is notable that these periods of intense innovation exhibit a strong correlation to preceding periods of price, demand or production volatility. This paper examines key trends in each theme between 1900 and 2018 and draws strong conclusions as to the interrelationship between them. INTRODUCTION The production of copper metal has increased from around half a million tonnes per annum to over fifteen million tonnes per annum over the course of the 20th Century. Contemporaneously, the average grade of copper ore mined has declined from over 2% to approximately 0.5% copper by weight. As a result, the volume of Run-of-Mine (ROM) copper ore required has increased from around ten million tonnes per annum to over a five billion tonnes per annum over the period, an unprecedented increase. The adage is that demand drives supply, that prices rise in times of high demand and/or short supply, and that prices fall when supply catches up with demand. The market sellers in biblical times knew this well; mediaeval market sellers equally. Dutch tulip sellers in the 1600’s experienced both in extremis — much to their dismay — and the great industrialists and early capitalists of the industrial revolution knew this also. Mining recently went through a cycle where investors and producers both believed that the “old” rules did not apply any more and that the industry was in a “supercycle” where prices would continue to rise on the back of increasing demand. However, as the GFC of 2008–2011 showed, this was not to be. Another adage says that we constantly innovate to lower costs of production. Is this true? Do we only innovate to lower cost? Has the true cost of producing copper actually gone down over the century? Or are there other balancing forces at play? Herb Kellogg, in his Centenary address to the American Institute of Mining Engineers (now SME), categorized two types of innovation: ‘Bigger and Better’, and ‘New Process’ (Kellogg, 1970). ‘Bigger and Better’ allows increased production at presumably lower cost; ‘New Process’ supports the same result at presumably the same scale, but at significantly enhanced efficiencies and (therefore) lower cost. It is suggested that both types of innovation are constantly and interchangeably required to achieve the kind of scale-up, at achievable operating and capital cost that the industry has achieved over the period. What can be shown, over this last Century and a bit, is that supply and demand are indeed inextricably linked, price and demand are linked, but so are price and cost of production. And the innovation required to sustain that weaves in between them all, cost-effectively increasing production capacity or lowering the cost of production at the same throughput, and sometimes both.

Jan 1, 2019

By Robert Benedetti

This paper describes various mitigation methods in order to reduce the maximum acceleration of the floorboard of hulled vehicles when explosive charges buried in water saturated sand were detonated beneath them. The effects on floorboard acceleration of adding a vehicle hull, several types of floorboard bracing, the use of foam to fill the gap between the floorboard and hull, and the use of foam to isolate the floorboard from the hull have been investigated. Small scale testing was conducted, which used bar magnet velocity gages to measure the velocity as a function of time of the center of the floorboard, directly over the charge, where the acceleration was expected to be greatest.

Jan 1, 2012

Australia is the world's leading producer and exporter of mineral sands. Despite increased production from some other countries in recent years, Australia maintained its No.1 position in 1988 among world producers of mineral sands concentrates. Production of the titanium minerals -- ruffle, ilmenite and leucoxene, as well as synthetic ruffle -- by the seven companies currently comprising the Australian industry increased in 1988 in response to continuing strong demand for feedstock by the pigment industry. Production of co-product zircon remained at the 1987 level, reflecting declining zircon grades. Exports of mineral sands concentrates increased in 1988; export earnings exceeded $300million. Prices for mineral sands concentrates are now at a historical high and, assuming that the world economy remains strong, real prices should continue to trend upwards in the short term. Exploration in the Eneabba-Cooljarloo region and the Scott River area, both in WA, the Murray Basin, Vic, and the central Queensland coast area, has identified substantial resources of heavy mineral sands. These discoveries have reversed the trend of the early 1980s of falling resources of mineral sands. In 1988, BMR estimated that economic demonstrated resources (EDR) of ilmenite, rutile, zircon and monazite combined was about 72.8 million tonnes. However, a substantial portion of the resources on the east coast are frozen as a result of environmental considerations. The proportion of mineral sands concentrates processed in Australia increased with the commissioning of two new synthetic rutile plants; Australia is now the world's leading producer of synthetic rutile (total capacity 272000 tonnes), most of it for export. Australia's two TiO2 pigment producers have both increased capacity, lifting national capacity by some 70p ercent to over 120000 tonnes/yr. As part of the expansion one producer converted from the sulphate to the chloride process. Other new pigment plants are being proposed for the future.

Jan 1, 1989

By M. H. B. Nasseri

Barre granite?s samples have been tested for fracture toughness under mode I along two different directions with respect to microstructural fabrics were investigated. 3D objects counter algorithm technique is applied on micro CT images to identify physical properties such as crack induced porosity, crack density, generated total surface area and contribution of individual mineral grains within the damaged zone.The result obtained justifies very well the fracture toughness anisotropy in Barre granite, and explains the difference in the structure of the damage zone evolving as a result of test crack interacting with pre-existing microstructural fabrics. The present study has potential application in the fields of rock mass stability, oil reservoir stimulation, rock fragmentation and damage in blasting and emplacement of dykes.

May 1, 2009

By C. Daniel Kealy

Finite-element,, mathematical models that solve LaPlace's and Richard's equations numerically were used to locate the phreatic surface within tailings pond embankments and to define the subsurface flow of water from the pond. Both must be known to design structurally and environmentally safe tailings dams. The permeability distribution within and beneath the embankment, the fluid potential values upgradient and downgradient from the embankment, and the geometry and elevation of an approximately impermeable layer at some depth beneath the embankment were used as computer inputs in analyzing over a dozen finite-element models of tailings dams varying structurally from simple to complex. Results predicted with the finite-element model were confirmed with measurements in a laboratory model of a tailings pond and in the field. Of particular importance to the design of safe slopes, all data indicated that the phreatic surface within a tailings dam is concave upward, a configuration opposite that in most earth dams. The close correlation between predicted and experimental values confirmed the practicability of using the finite-element technique to design safe tailings dams.

Jan 1, 1971

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By P. S. B. STEWART

As part of a continuing study of mechanisms of breakage, the grinding at Nairne Pyrites Pty. Ltd. was traced by the addition of barytes and the results compared with parallel small scale laboratory tests. It was confirmed that the same basic mathematical functions described the behaviour of the full scale ball mill as those established in the small scale mill. However, an additional classification function was required to define the behaviour for the rod mill and was evaluated as a function of size from the experimental data. The classification and grinding of the pyrites ore was assessed from steady state size distributions around the circuit.

Jan 1, 1971

Today’s world relies upon advanced green technologies that are made of critical elements with unique properties. Examples include rare earth elements (REEs) that are critical in the manufacturing of wind turbines and electric/hybrid vehicle batteries, key components of a greener future that face supply uncertainty and near zero recycling. To tackle their supply challenges, activities have begun for urban mining from waste electrical and electronic equipment (WEEE) that contain considerable amount of REEs, but their current level of recycling is less than 1%. Current recycling practices use either pyrometallurgy, which is energy intensive, or hydrometallurgy that utilizes large volumes of acids and solvents and generates large volumes of hazardous waste. In this study, we developed a novel and sustainable process to recycle REEs from WEEE, NiMH batteries in particular. The developed process relies on supercritical fluid extraction (SCFE) utilizing CO2 as the solvent, which is abundant, safe, cost effective, and inert. The effect of seven operating parameters, namely temperature, pressure, residence time, sample to chelating agent ratio, agitation rate, complex formulation, and methanol addition on REE extraction efficiency was investigated, and optimum operating conditions were determined. This work is the first to utilize a very efficient and safe process that runs at low temperature to extract metals from postconsumer products with minimum hazardous waste generation, while offering about 90% leaching efficiency for REEs. We expect our process to find widespread applicability in urban mining of REEs using green chemistry.