Search Documents

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By Marcial Medina

El presente texto describe la reología de la Pulpa a nivel de química de superficie y así sugerir las alternativas a los problemas que impiden poder operar en forma continua y su capacidad de diseño la Planta de Flotación Diferencial de Cobre – Molibdeno. Asimismo, es necesario definir una solución a escala de laboratorio, la cual debe ser validada con pruebas industriales e implementarla en planta. La estrategia debe garantizar la continuidad de la operación de la Planta de flotación de Molibdeno con cualquier tipo de mineral y que no presente compactación la pulpa. Finalmente, se devbe agarantizar el procesamiento de toda la producción de la planta de cobre en la planta de flotación diferencial de cobre molibdeno.

Sep 12, 2011

By W. D. Mcmillan

Soapstone is the term applied to an impure, massive, soft rock with a greasy feel. It is of variable composition, consisting chiefly, however, of talc, tremolite, and chlorite. Although limited quantities of soapstone are used as building material, in fireplaces, and in the manufacture of laundry tubs, sinks, laboratory-table tops, and-oven and furnace blocks, the principal part of the production is ground for use in roofing paper, insecticides, and as a filler in asphaltic paints.

Jan 1, 1949

By Bowen Li, Jiann-Yang Hwang, Mingsheng He, Huaguang Wang

Kyanite is one of the major high-alumina minerals for producing refractory ceramics. At high temperature, kyanite can be decomposed into mullite and amorphous silica. This change is an irreversible decomposition and provides potentials for fiber reinforcement of ceramic matrix. In this study, kyanite powder was compressed into a cylinder green body of ceramic and heated at 1150–1450 °C.The phase transformation of kyanite and sinterability were investigated by X-ray diffraction and scanning electron microscopy. The results showed that the phase transformation of kyanite started at 1150 °C when rising the temperature. At 1350 °C, kyanite is completely converted into mullite and silica. The compressive strength of the ceramics reached 73.3–134.8 MPa, while the bulk density was 1.95–2.47 g/cm3. The microstructure indicated the correspondence of the compressive strength to mullitization degree of kyanite.

Mar 1, 2017

By Harry G. Hedgepeth

Exploration of the Big Island trona beds by Stauffer Chemical Company started early in 1959. During the intervening time, Stauffer Chemical Company of Wyoming has developed a Large trona mine in this southwestern Wyoming area and has increased the over-all production of soda ash from natural sources by nearly one-half million tons per year. The trona, which is a hydrated sodium bicarbonate mineral, lies some 800 feet into the sedimentary rocks of the Green River formation. Present production is approximately 850,000 tons per year being extracted by means of a room-and-pillar mining system. Conventional coal mining equipment is used with some modification to accommodate local conditions. The mined and crushed ore is hoisted to the surface and processed in an on-site refinery. Refined soda ash is shipped to widely separated locations in covered hopper railraod cars. Construction in progress at Stauffer's plant will double the present capacity.

Jan 1, 1966

Upgrading and Removing Phosphorus from Low-Grade and High Phosphorus Containing Iron Ores

Sep 13, 2010

The resignation of Herbert Hoover, Director General of Relief in Europe, from his post as Chairman of the Board of Directors of the Food Administration Grain Corporation, in which capacity he had served for nearly two years; and the reorganization of the corporation under the name of the United States Grain Corporation, with Julius Barnes, United States Wheat Director, as its new head, took place at the annual meeting of the stockholders, held in New York, July 1. This action on the hart of Mr. Hoover is believed to be one of the first steps in his intended withdrawal from public service upon the conclusion of the war service of the various departments of the Food Administration, or as soon as they shall have been absorbed by other agencies. The Grain Corporation has been, for the past two years, a vast collection and distribution agency. Its function has been to assist in supplying to the Allies and the American Army and Navy large quantities of wheat, wheat flout, and other foods, with very little disturbance of American prices, and with such an even control of American distribution that reserves from one crop to another have been brought down to the lowest possible compass and without the dvelopment of actual scarcity anywhere in the United States. In the year just past, it carried on all the buying and the shipping for, the Belgian Relief Commission, until the commission retired on May 1 and the Belgian Government itself undertook its own overseas supplies. During the twenty-two months of its existence the corporation had disbursed $3,500,000,000 and collected an equal amount, selling for over-seas shipments commodities valued at $1,800,000,000, at an operating expense of about $3,250,000, or one-sixth of 1 per cent. During this time it has not lost a single dollar through fire loss.

Jan 8, 1919

For the past several years the policy of a large section of our mining industry in relation to our present bureaucratic form of government has become increasingly amusing, if not a little disgusting. In the past, mining men have always featured themselves the self-announced champions of free enterprise, and, generally, this conviction, was substantiated by their deeds. In recent years, however, a large group of the industry, while still expounding, from the front porch, the principles of free enterprise and a sound economy based upon the law of supply and demand, have gone around to the back door with palm extended, to join labor, farmers, bureaucrats, and other pressure groups to get their share of the take. The procurement of subsidies, bonuses, increased metal prices, and government assistance in a multitude of forms seems to have obscured from their thinking the welfare of the country as a whole and the sounder economic principles of a balanced budget and lower taxes. At the recent Colorado Mining Association convention in Denver, I. was alarmed to see just how far this specialinterest type of thinking has progressed within the mining industry. Government assistance to mining. was generally considered inadequate, and a flat bonus for any new mineral discovery was proposed. It was disquieting, too, to learn how far the federal alphabet agencies have entered into the mining industry and of the thousands of highly paid technical. men on the federal payroll required to man these numerous overlapping agencies and bureaus. Now all this is very fine, and some aspects of the federal give-away program can be very appealing to the unsuspecting in the mining industry as they have been to those in other groups. Some of these expensive programs may bring about a few dividends or even several new mines. But to this whole line of pump-priming reasoning there is one big disastrous fallacy.

Jan 1, 1952

By George F. Kunz

THE recently discovered occurrence of diamonds near Murfreesboro, Pike county, Ark., was brought to. our attention by Mr. Samuel W. Reyburn (Trustee for Messrs. C. S. Stifft, A. D. Cohn, August Zinsser, Jr., and himself, owners of the property), through whose courtesy we investigated the locality of the deposit. Prospecting with the diamond-drill is now in active progress ; but mining operations on a large scale have not yet been ordered. Geology.-The geology as well as the petrography of this interesting locality has been well described by Messrs. J. C. Branner and R. N. Brackett.1 Briefly summarized, the igneous rock in which the diamonds are found is a vitreous peridotite, forming a stock or volcanic neck, which has broken up through the Carboniferous and Cretaceous quartzites and sandstones. After an extensive period of erosion, during which an unknown portion of the neck and presumably a previously existent volcanic cone have been removed, the surface was covered with thin beds of Post-Tertiary conglomerate. The volcanic intrusion was accompanied by the formation of several small dikes of a rock much like that of the main body. One of these dikes cuts across the stock, while another cuts the Cretaceous sandstone, but is overlain by the conglomerate, thus giving a datum for the period of intrusion. So far as known, there was little, if any, metamorphism of the country-rock by the igneous magna, which probably followed an approximately vertical course, so that a more or less vertical extension downward of the igneous body to indefinite depths may be expected.

Mar 1, 1908

By Mark Cross, Diane McBride, Nick Croft

Extractive metallurgical processes rate amongst the most complex from the perspective of computational modeling. They typically involve multi-phase and multi-component fluid flow in very complex geometries, heat transfer driven by a number of interacting phenomena, solidliquid- gaseous phase change and mass transfer together with complex thermodynamics and associated chemical reactions. Beyond the model building itself, key challenges have always involved being able to identify the phenomena present together with interactions to characterize processes and experimental laboratory and plant data to parameterize the arising models – it is in this milieu, which require considerable process understanding and subtlety of thought, that David Robertson has made his contributions. We will review the achievements, over the last couple of decades, in computational modeling of extractive metallurgical processes and address some of the remaining challenges to enable simulation based process design, as we move through the 21st century.

Jan 1, 2014

At Namdeb, submerged beaches are earmarked for sampling and future mining and various sampling configurations are tested for optimality through the use of spatial simulations. For the creation of these virtual orebodies, basic statistics and variograms are needed, but in this specific instance no data exists from which the necessary parameters can be determined. The best that can be done is to use proxy data from onshore beaches, with adaptations where needed. The reworking of raised beaches during periods of rising and falling sea levels in some cases destroyed the internal beach structures, and it is very difficult to determine the variograms. A method is proposed whereby simulated annealing is used to adjust the sample locations to align the data pertaining to beach crests or cliff lines, thus improving the variogram structure along the shoreline in the direction of the highest geological continuity.

Jan 1, 2014

By J. A. Stampe

In connection with its investigations of strategic minerals in the United States, the Bureau of Mines ran magnetic surveys totaling more than 533,000 linear feet at 30 deposits of magnetite in northern New Jersey. These deposits occur in a belt of granitic gneiss and in limited areas of limestone. The ore consists of magnetite accompanied by score of the following minerals: Hornblende, augite, apatite, feldspar, biotite, calcite, garnet and pyrolusite. Results of these investigations are being presented in two reports of which this is the second. The first paper, Certain. Magnetite Deposits in New Jersey, by A. L. Neumann and McHenry Mosier, was issued in April 1948 as Report of Investigations 4225.

Jan 1, 1949

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

By Antonio de Lucas, Juan Francisco Rodríguez, Ignacio Gracia, Mª Teresa García

"The amount of waste of Polystyrene (PS) foams is increasing in last years due to their use in insulation, protecting and, storing many different food products. Conventional methods of recycling such as crushing and shrinking by heated air or frictional heat have the disadvantages of molecular degradation, resulting in a reduction of the quality of the recycled polymer. Dissolution and shrinking with suitable solvents is one of the cheapest and more efficient ways of polystyrene recycling but in the process of the solvent recovery by distillation a certain degree of molecular degradation is produced. In this way, CO2 supercritical technology appears as an interesting alternative for the elimination of solvent. This work proposes a global process to polystyrene recycling in two steps: a polystyrene dissolution with a suitable “green” solvent followed by its elimination by supercritical tecnologhy. In order to develop a “green process” the constituents of essential oils, limonene, terpinene, cymene, and phellandrene, are selected as the most appropriated solvents. Introduction In the last years, disposal of the non-biodegradable plastic wastes has been recognized as a serious environmental problem. Recycling these wastes has great interest in order to prevent the environmental pollution and to preserve natural sources (1, 2, 3). Since the Polystyrene foams (PS) is one of the most used foam in isolation, protecting and food storage most of recycling work is concerned with this polyolefin (4). The two main alternatives for treating polymer wastes are energy recycling, where wastes are incinerated, and mechanical recycling (5). Environmental argumentations such as toxic emissions are building up a public resistance against incineration process (6). Mechanical recycling is a popular recovery path for manufacturers and is carried out on single-polymer waste streams. Any way, the market for recycled products can only be found if the quality is close to that of the original. Unfortunately the process of classification and further recovery of these wastes makes them often more expensive than virgin plastic (7, 8). Solvent extraction is one of the cheapest and more efficient ways for PS recycling. If it is done in house of waste producers the separation between plastics could be easy and effective and the transport costs would be eliminated."

Jan 1, 2008

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

By R Dunne, W McCallum

Continuous improvement might be defined as seeking incremental improvement over time through improved equipment, processes, technology and the efforts of people. Most people working in ore processing facilities embrace the general principles of continuous improvement. However, given the industry-wide issues with skilled personnel and the constantly changing environment in ore processing facilities, it is often difficult to identify improvements in a facility over a given time period. The driver for these outcomes is the use of basic principles and technology to achieve best practice targets. The process involves four stages: develop standards of practice to define best practice in specific areas; write procedures to guide the organisation towards these best practices; implement the procedures and develop a review process to provide a method of measuring performance against best practice.By reviewing performance against best practice on a regular basis, the organisation measures progress towards the best practice targets and the incremental improvement between these regular reviews is a measure of continuous improvement.This paper provides the background for developing standards of practice for metal accounting, metallurgy and metallurgical management. The paper also describes how standards of practice can be used to develop continuous improvement and the skills set of the departmentÆs leadership team.CITATION:McCallum, W and Dunne, R, 2012. Metallurgical management tools for continuous improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 225-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R. E. Head

[Surveys of the manganese situation conducted by the Geological Survey any other agencies have definitely established the, fact that the tonnage of high-grade manganese or in the United States is relatively small. It is therefore obvious that large-scale production of manganese is possible only through beneficiation of low-grade material. Deposits of low-grade manganese ore are being examined by engineers of the Mining Division of the Bureau of Mines to determine their size and possibilities as sources of manganese on a tonnage basis. The Metallurgical Division of the Bureau is developing and perfecting beneficiation processes with the objective of utilizing such low-grade ores. Microscopic study of these ores represents one phase of the research.]

Jan 1, 1941

By David L. Durler

In-situ uranium mining is a relatively new and innovative method utilized for the commercial extraction of uranium. As with any mining method, however, significant environmental concerns will be evident and must be addressed in a rational and far-sighted manner. Experience has shown that radiological and non-radiological environmental problems may not manifest themselves until after the in-situ methodology has become established and matured to some degree. It is important, therefore, to recognize potential environmental concerns and incorporate them into an environmental program that spans the premining, mining, and post-mining phases of an in-situ operation.

Jan 1, 1982

WHILE in the employ of the Broken Hill Associated Smelters and the Electrolytic Zinc Oompanies at their South Melbourne Research Station, the writer was detailed to investigate the principles underlying the Parkes Process with a view of determining:1. The Interdependence of the variables:(a) Quantity of zinc required per charge,(b) Temperature of stirring of each zincing,(c) Silver content of the bullion after first zinculg,(d) Silver content of the bullion after second zincing,(e) Silver grade of the crusts produced for retorting, with reference to the method of working the Parkes Process then in operation at Port Pirie.2. The possibility of effecting improvements in the Port Pirie practice of desilverising, especially with respect to:(a) Silver grade of the crusts produced for retorting.(b) Quantity of zinc required per charge.The method of desilverising in practice at Port Pirie was a two-stage zincing.In both zincings the bullion was cooled to its solidification temperature and the silver crusts which separated from the lead were completely removed.The crusts from the first zincing were retorted, and the crusts from the second zincing were returned to the first zincing of the next charge.

Jan 1, 1925