Search Documents

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped don, a period of one hour or so is required. When a disturbance in the feed rate was made, the transient period extended to more than one and half hours (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content.

Jan 1, 1980

By Henry M. Howe

1. The purpose of the National Research Council as organized for war purposes is twofold, to stimulate those outside its own personnel to conduct researches of importance for winning the war and to carry on such researches through its personnel to a limited extent. How this is done is explained in Section 10. "Research" is used here in a very broad sense, including, for instance, inventing and developing mechanical and physical devices. The need of this work arises from the inevitable concentration of most of the governmental war agencies on the production and transportation of war materials of the types now adopted, as distinguished from devising new kinds of instrumentalities, such as armor, guns, aircraft, and apparatus for detecting, locating, observing, signaling, transporting, and many other military purposes. But it is important that we should devise new agencies. The war came near being won by an invention, the submarine, and its course has been affected greatly by two other inventions, tanks and aircraft. In spite of our numerical superiority victory may well be snatched from us by an invention, if we allow Germany to outstrip us in inventing. Hence the importance of the Council's work in mobilizing and organizing the services of the patriotic civilian experts throughout the country, so as to bring their powers to bear on important war problems and on inventing war devices, as an adjunct to the development work of the regular governmental bodies. 2. Status of the Council.—Though President Wilson's request caused the Council to be created in 1916 by the National Academy of Sciences under its congressional charter; though his executive order of May 11, 1918, directs the heads of "Governmental departments immediately concerned" to "continue to co-operate with it in every way that may be required;" and though the Government has contributed largely to its financial support; it is not a department of the Government but an independent research body, aiming to evolve the necessary mechanism for the novel work of systematic stimulation and guidance of research. Thus the Government, which instigated the creation of the Council, recognizes and collaborates with it, and in part supports it. The Council acts moreover as the Department of Science and Research of the Council of National Defense.

Jan 1, 1919

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By W. D. Hausel

The Wyoming craton in the western United States is a favorable terrane for diamond deposits. The craton hosts a variety of ultramafic, ultrabasic, and ultrapotassic rocks. Additionally, a few hundred 'kimberlitic' heavy mineral anomalies and some geophysical and remote sensing anomalies indicate the presence of undiscovered, mantle-derived, pipes in the craton. The Wyoming craton is separated into a Wyoming 'archon' known as the Wyoming Province, and the Colorado 'proton' known as the Colorado Province. The 'archon' underlies much of Montana and Wyoming and continues north into Alberta and Saskatchewan; the Colorado 'proton' underlies much of Colorado and a small portion of Wyoming. Although most exploration geologists would consider the 'archon' the most favorable terrane for commercial diamond deposits, the 'proton' has produced more than 120,000 diamonds, while the 'archon' has not been very productive.

Jan 1, 1996

By Henry Howe

1. The purpose of the National Research Council as organized for war purposes is twofold, to stimulate those outside its own personnel to conduct researches of importance for winning the war and to carry on such researches through its personnel to a limited extent. How this is clone is explained in Section 10. "Research" is used here in a very broad sense, including, for instance, inventing and developing mechanical and physical devices. The need of this work arises from the inevitable concentration of most of the governmental war agencies on the production and transportation of war materials of. the types now adopted, as distinguished from devising new kinds of instrumentalities, such as armor, guns, aircraft, and apparatus for detecting, locating, observing, signaling, transporting, and many other military purposes. But it is important that we should devise new agencies. The war came near being won by an invention, the submarine, and its course has been affected greatly by two other inventions, tanks and aircraft. In spite of our numerical superiority victory may well be snatched from us by an invention, if we allow Germany to outstrip us in inventing. Hence the importance of the Council's work in mobilizing and organizing the services of the patriotic civilian experts throughout the country, so as to bring their powers to bear on important war problems and on inventing war devices, as an adjunct to the development work of the regular governmental bodies. 2. Status of the Council.-Though President Wilson's request caused the Council to be created by the National Academy of Sciences under its congressional charter in 1916; though his executive order of May 11, 1918, directs the heads of "Governmental departments immediately concerned" to "continue to co-operate with it in every way that may be required;" and though the Government has contributed largely to its financial support (Section 12, page 10), it is not a department of the Government but an independent research body, aiming to evolve the necessary mechanism for the novel work of systematic stimulation and guidance of research. Thus the Government, which instigated the creation of the Council, recognizes and collaborates with it, and in part supports it. The Council acts moreover as the Department of Science and Research of the Council of National Defense.

Jan 12, 1918

By Raymond Rivera, Federico Cernuschi

Este documento trata de actualizar el conocimiento de un tipo de venillas no tan conocidas que llevan el nombre early halos. El reconocimiento de este tipo de venillas puede servir mucho para la vectorización lateral y vertical de un sistema porfirítico, pero debido a la escasa información que existe sobre ellas muchas veces son subestimadas, desapercibidas o hasta incluso confundidas con otros tipos de venillas. Este tipo de venillas son más comunes en los pórfidos Cu – Mo, mientras que en los pórfidos con afinidad hacia el Au (Cu – Au / Au – Cu) suelen ser más escasas o no estar presentes, pero aun así su débil presencia puede servir como una herramienta de vectorización.

Sep 30, 2022

By Zhitong Sui

Based on several case studies on the precipitating behavior of valuable nonferrous metal compounds (VNMC) in molten slags a green technology for the recovery of VNMC from molten slags was proposed. This technology involves three steps: (I) The selective enrichment of the dispersed VNMC into the designed mineral phase in the molten slag; (2) The selective coarsening of the designed mineral phase to a critical grain size in the molten slag; (3) The selective separation from tailing of the grown mineral phase in the solidified slag by dressing or hydrometallurgy processes. This is a clean and low cost technique and has a great capacity to deal with a large quantity of slags. The utilization of the recovered VNMC such as Titanium, Boron, Vanadium compounds was summarized as examples of application. It was confirmed by experiments that the precipitating behavior of the designed mineral phases like Perovskite(CaTiO3), Suanite(2MgO*B2O3) and Sincosite(CaOoV2O5*P2O5) in molten slags is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the VNMC from molten slags during solidification processes were also investigated.

Jan 1, 2003

By Debra W. Struhsacker, Jean Kiel, Jeffrey Thatcher

3.1 INTRODUCTION As heap leach precious metal projects become increasingly common in the United States, federal, state and local regulatory agencies are beginning to take a closer look at the short- and long-term environmental consequences of this recovery technology. From an operator's point of view, there is seemingly a confusing regulatory maze to be navigated and a plethora of permits and approvals to be obtained prior to commissioning a heap leach operation. The degree of difficulty associated with obtaining permits for a heap leach project depends largely upon the state in which the project is located. Permit acquisition is generally easiest in those states most familiar with heap leaching technology. For example, heap leaching is well understood in Nevada, and heap leach operations are relatively easy to permit, although permitting conditions in Nevada have recently become more stringent. However, many states are just beginning to become familiar with heap leach operations. Many of these states such as Idaho, Colorado, South Dakota, Oregon, Montana, Washington and South Carolina are in the process of drafting regulations and establishing guidelines for heap leach projects. In most cases, these regulations specify design and operating criteria as well as reclamation and decommissioning procedures. This chapter provides an overview of the regulatory and permitting aspects of heap leach operations. Permitting requirements for projects developed on federal land are discussed in detail. 'The state and local regulatory atmosphere and permitting requirements for various states are also presented. The chapter concludes with a generic permitting strategy. 3.2 KEY ENVIRONMENTAL CONCERNS The primary concern of most local, state, and federal regulatory agencies is the use, storage and transport of sodium cyanide (NaCn), and potential cyanide contamination of surface and groundwater resources. The toxicity of cyanide to people, fish and wildlife is also an important issue. Unfortunately, in the public eye, cyanide heap leaching has some emotional impacts similar to those associated with radioactivity and uranium mining. This perception and the general lack of understanding of cyanide can lead to unnecessary concern about cyanide contamination, further complicating the regulatory environment.

Jan 1, 1988

By Roland B. Drugge

The adaptation of pelletizing processes involves the coordination of various factors such as temperatures, gas flows, productions, etc., in order to obtain optimum performance. The consequent problems are considerable due to the large number involved as well as the lack of knowledge of their correlation. It is therefore essential to establish a fundamental theory which takes into account the heat transfer phenomena and the secondary factors which are relevant to the properties of the product. Straight grate and grate kiln pelletizing processes involve heating of a stationary bed on a travelling grate. The heat transfer conditions are therefore of primary importance. This is why this article pays particular attention to conditions which obtain when a stationary bed is heated, in which certain special reactions occur. The conclusions drawn from this penetration of the heat transfer phenomena can be expressed in postulates acting as guide-lines for the establishment of proto-typal processes. Examples of elaborating such processes are also given in the article. Some operational experience at LKAB are also given.

Jan 1, 1975

By Allen Rogers

IT has always seemed to me that there is a certain similarity between the work of the mining engineer and that of the doctor of medicine-each has very often to be governed in his actions by conditions which he cannot. see. It is not necessary to detail the unseen conditions with which the mining engineer or geologist has to deal-the further extension of orebodies; the existence of new ones, the throw of a fault, the probable change in grade or character of the ore with advance of the workings, are a few of the conditions which the mining engineer has to determine as well as he can from the deductions he is able to make from what he can observe. Just so the physician is often confronted with conditions that he can not observe. Probably less than half of human ills make a manifestation at the surface of the body from which definite and certain conclusions can be drawn. The diagnostician must observe various things and, from these observations in combination, conclude what 'his course should be to bring about the cure of the trouble. Both professions would be assisted immensely by any agency that would permit them to look below the surface, something that would make more certain the diagnosis which each is called upon to make. The physician has had such an agency since 1895, when Röntgen discovered the X-ray; which, by making possible shadowgraphs of the osseous portion of the human body, advanced immensely the diagnosis of bone lesions. Later, with improvement in the technique and more understanding in the interpretation of what the photographic plate shows, other portions of the human anatomy could be examined and at the present time there is hardly an instance of internal disorder to which the aid of the X-ray is not called. Some organs are made opaque by administering mineral substances; in, other cases, conclusions are drawn from barely perceptible shadows on the photographic plate. Generally the surgeon's knife is directed with exactitude to the seat of the trouble and so not only is the difficulty revealed but the necessity for an exploratory' operation is averted.

Jan 1, 1928

By A. Robison, V. T. McLemore

"The San Juan Basin, New Mexico contains many heavy mineral beach-placer sandstone deposits of Cretaceous age. Beach-placer sandstone deposits are concentrations of heavy minerals that formed by mechanical concentrations (i.e. settling) of heavy minerals on beaches or in longshore bars in a marginal-marine environment. They have high concentrations of several elements, such as Ti, Zr, rare earth elements (REE), Sc, Y, U, Th, Nb, Ta and Fe. These elements are becoming increasingly more important to industry, because they are used in the manufacture of devices our society uses every day, i.e. cell phones, computers, and alternative energy devices, like solar panels. It is unlikely that any of the beach-placer sandstone deposits in the San Juan Basin will be mined in the near future because of small tonnage, low grades, high iron content, and distance to processing plants and markets. However, as the demand for some of these elements increases because of increased demand and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Current studies at the New Mexico Bureau of Geology and Mineral Resources are focused on the Apache Mesa (formerly Stinking Lake) deposit near Dulce, New Mexico. INTRODUCTION Beach-placer sandstone deposits are accumulations of heavy, resistant minerals (i.e. high specific gravity) that form on upper regions of beaches or in long-shore bars in a marginal-marine environment. They form by mechanical concentration (i.e. settling) of heavy minerals by the action of waves, currents, and winds (Fig. 1; Bryan et al., 2007). Modern examples are found along the Atlantic Coast, USA (Koch, 1986; Carpenter and Carpenter, 1991), southeastern Australia (Roy, 1999), and Andhra Pradesh, India (Rao et al., 2008), where they are mined for titanium, zircon, and monazite (a Ce-bearing rare earth, REE, mineral). Detrital heavy minerals comprise approximately 50-60% of these sandstones and typically consist of titanite, zircon, magnetite, ilmenite, monazite, apatite, rutile, xenotime, garnet, and allanite, among other minerals. Most of these minerals have a high specific gravity exceeding 4 and are dark colored, giving the sandstones a dark color, resulting in them being called black sandstones. Although beach-placer sandstone deposits are found in strata of all ages; the deposits in the San Juan Basin in New Mexico are restricted to Late Cretaceous rocks belonging to the Gallup, Dalton, Point Lookout, and Pictured Cliffs Sandstones (Fig. 2; Table 1; Chenoweth, 1957; Houston and Murphy, 1970, 1977). The beach-placer sandstones are black, dark gray, to olive-brown, resistant to erosion, and radioactive due to radioactive zircon, monazite, apatite, and thorium minerals. Anomalously high concentrations of Ti, Fe, Nb, Th, U, Zr, Sc, Y, and REE are characteristic of these deposits. Similar Upper Cretaceous heavy mineral, beach-placer sandstone deposits are found throughout Montana, Wyoming, Utah, Arizona, and Colorado (Dow and Batty, 1961; Houston and Murphy, 1970, 1977; Zech et al., 1994)."

Jan 1, 2016

By Janet A. Johnson, T. B. Borak, K. J. Schiager

INTRODUCTION In the USA regulatory agencies have adopted standards which limit the allowable concentration of ore dust in underground uranium mines. The American Conference of Governmental Industrial Hygienists has recommended a threshold limit value for silica which has been incorporated by reference in federal regulations (30 CFR 57, 1980). The Nuclear Regulatory Commission (NRC) imposes a limit for unprocessed uranium ore dust for reducing the exposure to radioactive materials from inhalation (10 CFR 20, 1980). We have been unable to trace the origin of the NRC standard. Recently the ICRP has published recommendations concerning limits for intakes of radionuclides by workers (ICRP, 1979). We have used the ICRP methodology to compute the dose equivalent commitment to lung and bone from inhalation of insoluble ore dust particles. These values were used to derive air concentrations which would provide an acceptable risk for induction of cancer from occupational exposure. Results indicate that the new ICRP recommendations are more restrictive than the present NRC standard for radioactivity. The maximum allowable dust load in a uranium mine will depend on both the concentration of silica (% Si02) and the amount of radioactivity (% U308). We have combined these standards assuming complete independence of biological hazard to establish boundary conditions for which either silica or radioactivity is the dominating factor. Based on these results we present suggestions for analysis of ore dust to insure compliance with regulatory agencies. SILICA STANDARDS Silicosis, fibrotic lung disease produced by crystalline silica, was one of the earliest forms of occupational disease to be recognized. The pulmonary lesions caused by silica, silicotic nodules, consist of concentrically arranged bundles of collagen fibers. Fusion of these nodules results in progressive massive fibrosis causing alveolar changes which decrease ventillation and blood flow in the lungs. The current Threshold Limit Value (TLV) for mineral dusts is based on the concentration of free silica. The standard is expressed in three forms: (1) Particle count standard: TLV (mppcf) = 300/(% Si02 + 10) (mppcf = million particles per cubic foot) (2) Respirable dust mass standard: TLV (mg/m3 ) = 10/(% respirable Si02 + 2) (3) Total dust standard: TLV (mg/m3 ) = 30/(% Si02 + 3) The most commonly used form is the respirable mass standard. These curent values for silica are based primarily on epidemilogical studies of Vermont granite workers and other occupationally exposed workers. In the Vermont study no cases of silicosis were seen in individuals employed after dust control measures were initiated and whose subsequent exposure averaged less than 5 mppcf. The free silica concentration in the airborne dust to which these workers were exposed averaged 25%. A concentration of 10 mppcf of granite dust is considered equivalent to 0.1 mg/m3 quartz. The current respirable mass standard allows a maximum silica concentration of 0.1 mg/m3. NIOSH (1974) has recommended a reduction in the current TLV for respirable silica to 0.05 mg/m3 Si02. As with radiation standards, the TLV for mineral dusts is an upper limit for time weighted average exposure. It is recommended that dust concentrations be maintained as far below the TLV as current practices permit. RADIATION STANDARDS The present concentration limit for airborne natural uranium in ore dust prior to chemical separation is 75 µg of uranium per m3 of air ( 10 CFR 20, 1980) . This corresponds to 1.85 Bq/m3 (50 pCi/m3 ) of natural uranium, U-238, U-235 and U-234 and is equivalent to 3.7 Bq/m3 (100 pCi/m3 ) of gross alpha activity with radioactive equilibrium between the long-lived alpha progeny through Ra-226. The origin or basis for this standard is not known, but it presumably includes both chemical toxicity and risk from somatic radiation injury. Recently the International Commission on Radiological Protection (ICRP, 1977) has published recommendations concerning the objectives and criteria for limiting radiation exposures. This was followed b y a revision of the limits for intake of radionuclides by workers (ICRP, 1979; ICRP, 1980). The previous compilation of limits for internal emitters was published by ICRP Committee II in 1959 (ICRP, 1959). The latest version includes new methodlogy outlined in ICRP Publication 26 (ICRP, 1977) as well as extensive metabolic information

Jan 1, 1981

By Yves Bellemare

Entre 1983 et 1997, l'exploitation de la pierre de taille au Québec a été marquée par l'émergence et la consolidation de plusieurs nouvelles variétés de granit, provenant exclusivement ou presque de la Province de Grenville. Le Québec demeure toujours le principal expéditeur canadien de granit dimensionnel, avec des expéditions annuelles représentant près de quatre-vingt-dix pour cent des expéditions totales canadiennes de granit brut et transformé. La production annuelle de granit brut oscille, depuis 1994, autour de cent mille tonnes métriques. Cette production a plus que doublé de 63 000 à 140 000 tonnes métriques entre 1981 et 1990, mais elle a connu une chute importante en 1991 (67 000 tonnes métriques); cependant depuis 1994, elle est en forte progression (Ménard, 1998). En 1983, le granit dimensionnel était extrait de plus de vingt-cinq carrières, dont les trois quarts se localisaient dans la Province géologique de Grenville. Comparativement, en 1997, le Québec comptait trente-sept carrières actives, dont trente-cinq dans le Grenville (Gaudreau et al., 1998). Cette concentration des carrières dans la Province de Grenville s'explique par la demande accrue de nouveaux produits au fil des ans et par le potentiel élevé de découvertes de nouvelles variétés dans cette Province géologique. L'accessibilité au territoire, toujours plus grande, a facilité la mise en production de carrières favorisant la diversification des produits. Le ministère des Ressources naturelles du Québec (MRNQ) a consacré depuis 1980, beaucoup d'efforts dans la recherche de nouveaux gisements et de nouvelles variétés. En plus des programmes de subvention destinés aux prospecteurs ou aux compagnies, le ministère a réalisé des campagnes d'inventaire de pierre de taille, de pierre concassée et de pierre d'enrochement pour en connaître le potentiel géologique et à orienter les recherches futures (Nantel, 1983; Nantel et Martignole, 1991; Bellemare, 1995a, b, c, d, e, f, 1997, 1998a and b; Bellemare et Petryk, 1996a, b, c and d). Cette étude donne un aperçu des différentes variétés de pierres extraites dans la Province de Grenville entre 1983 et 1997, les situe dans leur contexte géologique et en localise les principales régions productrices. Elle est une suite à l'article publiée par Nantel (1984).

Jan 1, 2001

The Mine Safety and Health Administration (MSHA) academy in Beckley, WV, received enquiries from various segments of the mining industry concerning alcohol and substance abuse in the mining industry. The MSHA Director formed a committee, the Mining Industry Committee on Substance Abuse (MICSA), to deal with these enquiries. The committee met in April 1985 at the mining academy in Beckley. The MICSA committee expanded its membership to represent labor, management, and government agencies affiliated with the mining industry as well as government agencies dealing with alcohol and drug abuse. This expanded 18-member committee met for the first time in July 1985. At that time, two cochairmen were elected, one from labor and one from management. MICSA has spent time on education by sharing information on the issues and by calling in outside experts for advice and consultation. The committee also initiated several projects. These include a resource manual on substance abuse and employee assistance programs. Mine operators and labor unions can use these programs as guides. MICSA is also assembling statistics on substance abuse, particularly as applied to mining. And the committee commissioned an Education film, Substance Abuse, Is It Our Problem? (The results of a survey on drug use, given in Table 1, suggest that substance abuse may indeed be a problem.) The educational film, produced by MSHA, is an introduction to the problem of substance abuse in the mining environment. The film encourages mine operators, labor unions, and miners to analyze their individual circumstances to determine whether a problem exists. The film also offers ways to deal with the problem. And the film invites the mining industry to request additional information from MICSA. There is no single approach to substance abuse that will fit the need of every mining operation. As with any health, safety, or production problem, remedies must be site specific. MICSA's aim is to channel ideas to those who seek to help employees in a mining environment who seek to rid themselves of alcohol and substance abuse. As stated more formally: The Mining Industry Committee on Substance Abuse represents the efforts of labor, management, and government. The mission of the committee is to make the mining industry aware of the problems resulting from alcohol and other drug abuse and to recommend possible methods to remedy the problem. The function of the committee is to assist the industry in developing programs and resources to recognize and provide help for troubled employees, and thus reduce the risk of accidents, while lower absenteeism and increasing productivity.

Jan 11, 1987

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The US Bureau of Mines (USBM) and Amax Coal Co. studied surface coal mine overburden blasting near four steel and one PVC pipeline of 15 to 51 cm-diam (6-20 in.-diam), monitoring vibration, strain and pressure. Unlike tests of small blasts simulating construction, these were up to 1 t (2200lbs) per delay in 31-cm (12-in.) blastholes. Worst-case comparisons showed that 12.7 cm/sec (5 in./s) blasting vibrations produced strains about one fourth that of pressurization and 10% to 18% of the ultimate tensile strength. No failures occurred from blasting as close as 15 m (50 ft), which produced vibrations over 60 cm/sec (24 in./s).

Jan 1, 1995

By T Barto, D Thomson, T Norgate, C Doblin

Collaboration between CSIRO Minerals and SunSalt Pty Ltd, a salt producing company located in rural Victoria, has resulted in a commercial process to recover magnesium sulfate (commonly called Epsom salt) from the saline waters of the Murray Basin. The feed for this process is bittern; the liquor remaining after halite (common salt) has been harvested from the saline water by evaporation.SunSalt produces salt and bitterns from three locations, namely Hattah (Victoria), Mourquong (NSW) and Wakool (NSW). The small size and considerable distances between these operations makes it uneconomic to build a stationary processing plant to extract value-added products, in particular Epsom salt, from the bitterns of the three operations. This fact led SunSalt to build a containerised mobile plant that could be moved to each site to process the bitterns at the end of the salt harvesting period.Epsom salt is extracted from the bittern by further evaporation, refrigeration and recrystallisation. In this process the bittern is diluted with five per cent volume of fresh water to minimise precipitation of residual halite in the bittern. Cooling the diluted bittern to between -5 and -10¦C precipitates up to 70 per cent of the magnesium sulfate, which is recovered as 85 to 96 per cent purity Epsom salt by filtration. This product is marketed as an industrial grade Epsom salt. Higher purity (up to 99.9 per cent) Epsom salt (USP or BP grade refined product) is made from the industrial grade product (raw Epsom salt) by recrystallisation.The containerised mobile plant was commissioned in December 2002. The raw Epsom salt generated in the mobile plant is refined to a higher purity Epsom salt in a separate plant located in Mildura. The Mildura plant was commissioned in December 2003.The CSIRO-SunSalt collaboration has demonstrated that the saline waters can be processed into a useful resource, and in addition could create jobs and a new skill base in regional Australia. The production of Epsom salt locally in Australia, which is worth currently about $A600 per tonne, removes the need to import over 3000 tpa from overseas with a net positive impact of $A2 million on the balance of trade.

Jan 1, 2004

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011