Search Documents

By H. G. Papacek

The Fabrica Mine of the Brazilian iron ore company Ferteco mines on an extremely inhomogenous ore deposit. A large amount of the crude ore consists of fines minus 100 micron which cannot be sold without further treatment because of its chemical and physical properties. In order to make full use of the mined crude ore an expansion program has been realized which incorporates among others a concentrator to produce classified blast furnace ore , sinter feed and pellet feed. The pellet feed is converted in a 2.5 million tons per year Lurgi Dravo plant into high grade pellets. The paper discusses the selection of the concentration process, the pelletizing process and describes the experiences with the operation plant during the startup and the first years of operation.

Jan 1, 1979

By S. Sun

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest is reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi-component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By M. Misra

The volume of low-level contaminated soil at the. Department of Energy's Nuclear Weapon Sites are in the order of several million tons. Most of the contaminants are uranium, plutonium, other heavy metals and organic compounds. Selected Physical separation processes have shown demonstrated potential in COD Centratingthe radio nuclides in a small fraction of the soil. Depending upon the size, nature of bonding and distributions of radio nuclides, more than 90 percent of the radio nuclide activity can be concentrated in a small volume of fraction of the soil. The physico-chemical separation processes such as flotation in a mechanical and microbubble tall column cell have shown, promising applications in cleaning up the high volume contaminated soil.

Jan 1, 1995

By G. W. Bonnell, D. A. Young, D. G. Genter

Through 1996 and 1997, CANMET and the Cape Breton Development Corporation (CBDC) conducted a project to study the Phalen Mine’s 7 East longwall ventilation network to help determine methane emission patterns that were having a negative impact on coal production. Increased methane emissions were primarily related to mining depth and were also affected by the influence of a large sandstone body located above the worked seam. The research included the installation of tube bundle systems to monitor waste (gob) methane and pressure differentials. The focus of this paper is on the novel use of tracer gas techniques that helped shed light on the performance of the ventilation system and in determining the methane migration paths in the waste.

Jan 1, 2001

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

The effect of conditioning energy input on the metallurgical results of an emulsion flotation process has beenattributed by previous authors to a detergency process.This paper shows that such a process does not explain the data and that an attrition mechanism is more appropriate.

Jan 1, 1970

Samples weighing O· 2 g are digested with 2 ml of 72 per cent perchloric acid for 2 hr at 180°C, and then diluted to 10 ml. with water. After settling, an aliquot of clear solution is reduced with ascorbic-citric acid, and then a zinc dithiol solution is added to form a coloured molybdenum complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 2 p.p.m. may be analysed at rates up to 150 determinations per day.

Jan 1, 1970

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Mine explosions are one of the most concerning risks related to underground coal mining, as a single gas explosion can cause injuries and fatalities among miners. Underground infrastructure seals and build-in-place (BIP) refuge alternatives (RAs) are employed to isolate an area from active workings to mitigate coal mining-related accident risks. They are designed to withstand blast pressures from a possible accidental detonation of the contained gas or a coal dust explosion. Crosscut seals and BIP RAs, typically consisting of steel-reinforced concrete, are prone to strong convergence and have a significant leakage potential due to high convergence damage near mined-out areas. The roof-to-floor convergence can change the structural integrity of these structures, and altered structural integrity can lead to less explosion resistance capability. Hence, a thorough analysis is needed to further understand their explosion response under various strata conditions.

Jul 1, 2023

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

During a mineral exploration program in an environmentally sensitive area nearMount Painter in South Australia, a helicopter was used to position, construct and service drilling rigs in order to avoid the need to create new access tracks. The drilling program was designed to optimise the advantages of natural landforms in order to minimise the environmental impact of site construction and drilling activities. This minimisation of land disturbance reduced the required amount of rehabilitation measures to the extent where all impacts of the helicopter-supported programme had disappeared within 12 months of completion of work.

Jan 1, 1995

By Ken-ichiro Uemura

"The DIOS process has been developed for eight years since 1988. The research project was started with the element studies carried out by each of the five integrated steel making companies in Japan, the final two and half years were spent for the pilot plant studies. Operation were conducted in the entirely closed and pressurized system successfully as planned. From the result, the DIOS process was proved to be viable as a future iron-making process substitutable for the conventional blast furnace. In addition, a lot of findings were obtained. Hot metal productivity was primarily determined by a oxygen flow rate, and a coal consumption varied depending on the productivity. The post combustion ratio was a little lower than expected from the result of the element study. It was supposed to relate the gas-reforming with coal or volatile matter in the free space of the furnace. Hot metal carbon content seemed to depend on the char content in slag.INTRODUCTIONThe JISF's DIOS pilot plant (DIOS=Direct Iron Ore Smelting Reduction Process) has finished its last campaign of the operations in January 1996. The project was started in 1988 as a joint research of the Center for Coal Utilization, Japan and the Japan Iron and Steel Federation (JISF) with a subsidy for promoting coal productions and utilization technologies from the Agency of National Resources and Energy, the Ministry of International Trade and Industry(MITI). Throughout the pilot plant test, a total of over 20,000 tons of hot metal was produced for more than 2,000 hours of the operation. Recorded production rate was 538 ton/day for 3 days at a specific coal consumption of approx. 1,000kg/hmt. Long-term operation was carried out in the fifth campaign for 18 days, which has proved that the entirely closed and pressurized DIOS process works well as planned. In Figure 1 is shown the representative operational performance obtained in the first five campaigns. The project is going to be finished by the end of March this year after investigating the technical viability and economic potential of the process, and completing the conceptual design of the DIOS commercial plant. In this paper, the system and facilities of the DIOS process are first introduced and some of the results of the pilot plant test are detailed later."

Jan 1, 1996

By NEWTON B. KNOX

IN Bolivia, mining is still the principal economic activity, as it was before and during the Spanish Colonial period. Tin, tungsten, antimony, copper, lead, zinc, gold, silver, sulphur, and a little bismuth are produced. The Andes mountains are divided into two main ranges in Bolivia; the Western range marks the border with Chile and the Eastern range forms the backbone of the country; in the North it drops rather abruptly eastward, to the plains of the Beni, whereas in the South it splits and is separated from the Chaco flatlands by a series of folded mountain ranges. In general the mineral deposits are found within the Eastern range or in the hills that rise from the high plateau between the ranges - really parts of the Eastern range partly submerged by recent sediments. The mineral belt is thus over 500 miles long and about 100 miles wide and includes most of the principal centers of population and the most important means of communication. The region is mountainous and the roads are bad; furthermore labor is a serious problem, for the land is poor and the agricultural population is never far from hunger. The floating supply of miners is limited and soon exhausted in any emergency like the present.

Jan 1, 1945

By Raja V. Rarnani, Robert L. Frantz

"The Generic Mineral Technology Center for Respirable Dust (GTCRD) was created at The Pennsylvania State University and West Virginia University by a congressional initiative in 1983 responding to recommendations in the 1980 National Academy of Sciences study on the Measurement and Control of Dust in Mines. Many of these recommendations dealt with the need to initiate focused fundamental research for further professional progress in dust control. Long-term, sustained support was emphasized to develop expertise in respirable dust research. In creating this Center, Penn State and West Virginia University were specifically recognized for their expertise in and facilities for research on coal mining and medicine. Today, the Center includes the Massachusetts Institute of Technology, the University of Minnesota, and the Michigan Technology University. The Respirable Dust Center is the only organization that coordinates and integrates the medical, scientific, and engineering aspects of respirable dust disease. The Center works with the U.S. Bureau of Mines (USBM), Mine Safety and Health Administration (MSHA), the National Institute for Occupational Safety and Health (NIOSH), the United Mine Workers of America (UMWA), and the U.S. coal industry in defining the research priorities for the programs of the Center to enhance research synergism.The Center's mission is to enhance the health, safety and productivity of miners by advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs to reduce the incidence and severity of respirable dust disease.All Dust Center activities are focused to be responsive to this mission, which is shared by the several federal agencies closely associated with the GTCRD. While significant progress has made mine atmospheres cleaner and healthier, respirable dust-related disease remains the nation's most pernicious industrial hazard.The goals of the GTCRD were formulated with recognition of the diverse scientific, engineering, and medical aspects of respirable dust, in addition to a need to enhance researcher interaction, as well as education and technology transfer efforts, in the respirable dust area. These goals reflect the needs of the mining industry as determined by the National Academy of Sciences Committee on Measurement and Control of Respirable Dust study done in 1980. The report of this committee encouraged the Bureau of Mines to redirect its research efforts ""...toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust."" The GTCRD's goals, detailed in chapter three of this document, were formulated to mesh with NAS recommendations."

Jan 1, 1995

By C. K. Leith

CERTAIN ideas on iron and steel sanctions to follow originated in a series of conferences held under the joint auspices of the War Department and Brookings Institute in Washington last spring. The views presented may be regarded as those of substantial segments of the steel industry. In view of the fact that steelmaking capacity can be so quickly converted to the production of armament, any effective control must necessarily include the entire steel industry and not solely the parts devoted to the production of implements of war. It must also be exercised all the way from production and shipment of raw materials through their ultimate conversion into finished products and use. Control will be dis- cussed under two main headings: (I) control of raw materials at the source; (2) control of steel capacity within the Axis countries.

Jan 1, 1944

By R. D. Shackleton

Medusa Cement Company, a division of Medusa Corporation, is a medium-sized cement manufacturer serving the midwest, east, and southeast. Medusa's eight plants are located in Georgia, Pennsylvania, Ohio, Illinois, Michigan, Wisconsin, and Canada. Of these, six have active limestone, shale, clay, and sand quarries now in operation. This paper deals with the various individual state laws regulating mining and reclamation at the Georgia, Illinois, and Pennsylvania quarries. Several recommendations for future state mining laws are discussed also.

Jan 1, 1974

By H. W. Breathitt

World demand for phosphate rock has increased significantly in the past fifteen years. Prior to the early 1960's, most of the world production was obtained from Florida, North Africa, and Kola. As the 1960's arrived, new mines in North Florida and Eastern North Carolina, as well as expanded production in the Western United States, .increased domestic production. Many new mines overseas have also become significant. This includes countries such as Senegal, Togo, Israel, Spanish Sahara, and Jordan. Limited production, often as by-products, has been noted in South Africa, Brazil, and other countries. In recent years, and even recent months, we have learned of many new areas being considered as potential sources of phosphate rock. This includes Australia, Saudi Arabia, Mexico, Colombia, and Brazil. Many other developing countries have discoveries and are considering their new deposits, often with difficult beneficiation problems, as potential sources of phosphate. These factors all relate to expanded world, population and the demand for more fertilizer products to produce food. In this paper, four areas of the world with different types of phosphate deposits are briefly reviewed to contrast the ore beneficiation problems to Florida procedures--long considered the "standard" of the industry, at least for most of the United States' domestic production. Agrico has three large operating mines in Florida with total production capacity exceeding seven million tons per year. Here, pebble phosphate (+14 mesh material) is produced without the use of flotation, whereas all of the material finer than 14 mesh is subjected to flotation beneficiation to upgrade into high grade concentrates.

Jan 1, 1977

By F. K. McIntosh, L. A. Dahmers

"INTRODUCTION North Carolina has been the leading producer of mica in the United States, accounting for roughly 50 percent of the Nation's output. The producing area is a belt some 100 miles in width lying in the Mountain and Piedmont sections in the western part of the State. Ashe, Watauga, Avery, Mitchell, Yancey, Buncombe, Haywood, Jackson, Macon, Transylvania, Rutherford, Cleveland, and Lincoln Counties supply the bulk of production, while small amounts have been produced in Gaston, Catawba, Burke, Wilkes, Yadkin, Stokes, and Person Counties.To assist the operators and expedite the production of mica during the recent emergency, the Bureau of Mines drilled four of the more promising mica properties in this State. The results of this exploratory program are recorded in this report.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, L. B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests."

Apr 1, 1948