Search Documents

By R. L. Grunes, F. K. Kies, C. D&apos, Antonio

THE several studies concerned with the annealing of thin nickel films have largely been restricted to films of a single thickness.1-4 It is well-known, however, that both physical and mechanical properties depend upon film thickness.5, 6 The strength-thickness relations found in vapor-deposited nickel films in the annealed and as-deposited states, as an example, are at least partially due to the density and arrangement of imperfections within the films.7, 8 For these reasons, the annealing characteristics of thin nickel films as a function of thickness were investigated. Electrical resistance was chosen to monitor annealing behavior since resistance changes are partially dependent upon defect structure. In addition, the equations predicting film resistivity as a function of thickness are already available.9, 10 Further advantages afforded by electrical-resistance measurements are its adaption to continuous readings during annealing and its relative simplicity. Nickel films were vapor-deposited, at average rates of 60Å per sec, on Vycor substrates held at room temperature in vacuums of about 10-5 torr. Afterwards, deposition-thickness measurements were made using a multiple-beam interferometric technique. A more detailed description of deposition procedures and the interferometer appear elsewhere.7, 8 The four-probe method was employed in measuring electrical resistance since this technique measures film resistance without contributions from lead wires and contacts. Resistance measurements were made before, during, and after annealing to temperatures of 700°C under vacuums of approximately 10-4 torr. Measurements were made every 25°C or more often when necessitated by unusual resistance changes. Cooling and heating rates were maintained at approximately 5°C per min. Typical resistivity vs temperature curves are shown in Figs. 1 through 4. It is apparent from these

Jan 1, 1965

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By Benoit Bissonnette

"The need for production of a competent fill was recognized early by the project partners. Consequently, a 4000 Ud paste fill plant was constructed and commissioned in early August 1994.In order to fine tune the process without risk to the underground workings, a closed pumping loop was devised on surface. After two months of this exercise, the first underground slope was filled according to specifications obtained from the pilot plant trials.This paper will focus on the operational problems encountered and the solutions adopted so far, and on a comparison between expected and actual fill production and characteristics.RésuméLa nécessité de produire un remblai de propriétés mécaniques suffisantes a été rapidement reconnue par les partenaires du projet. Conséquemment, une usine de production de remblai en pate, utilisant les residus du concentrateur d'une capacité de 4000 t/j a été construite et l'opération a débuté au mois d'aôut 1994.Dans le but de roder le précedé sans mettre en danger les installations souterraines, l'usine a été testée dans un circuit de surface. Après deux mois d'essais, le premier chantier souterrain a été rempli avec du remblai en pate selon les specifications dérivées de l'usinage pilote.Cet article présente les problemes d'opération rencontrés et leurs solutions, en plus de faire une comparaison entre les résultats prévus et ceux actuellement obtenus sur la production et sur les charactéristiques du remblai."

Jan 1, 1996

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By M. Kawakami, K. Suzuki, T. Takenaka, S. Yokoyama

Molten NaNO3-NaNO2-KNO3mixture is used as a heat transfer medium at high temperature. One of the most important properties of this mixture is the heat capacity. In the present work, the enthalpy change with temperature was measured by the drop calorimetric method to evaluate the heat capacity. The results are summarized as follows: The enthalpy of the mixture increased linearly with the temperature. From the slope of the line, the heat capacity was evaluated. The heat capacity of pure NaNO3, NaNO2and KNO3was 0.129,0.110 and 0.142 kJ/mol/K, respectively. These values are in fairly good agreement with the published data. In the binary and ternary systems, the molar additivity of heat capacity, which is well known as Neumann-Kopp’s law, was obtained. The heat capacity of HTS1and HTS2, which are well known ternary mixtures of practical use, were in the range of published data.

Jan 1, 2004

By Frank E. Chase, John L. Ellenberger, Christopher Mark

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

By Edward (Ted) Dowey

City Water Tunnel No. 3 is being built in order to provide a redundant system for delivering 4,542,500 m3 (1.2 billion gallons) of water per day throughout the five boroughs of New York City. The present tunnels, City Tunnel No. 1 and 2 (Figure 1), were put in service in 1917 and 1936 respectively, and both have been in continuous service. Tunnels No. 1 and 2 can-not be shut down for inspection or repair until City Tunnel No. 3 has been completed. City Tunnel No. 3 has two stages (Figure 1).Stage One is 20.1 km (12.5 mi) long and is presently delivering drinking water to the boroughs of the Bronx and Manhattan. Stage Two consists of the Brooklyn-Queens Tunnel 17.7 km (11 mi) and the Manhattan Tunnel 14 km (9 mi). The Brooklyn-Queens leg is complete and is set to be put in service soon. The Manhattan Tunnel is being constructed and is the subject of this paper. The Manhattan Tunnel (Figure 1) is comprised of three legs: the north, south and east legs. The con-tract includes the excavation of 8,976 m (29,500 ft) of tunnel and the lining of 14,561 m (47,773 ft) of tunnel. The south tunnel, 5,705 m (18,720 ft), was excavated but not lined, under a previous contract. The tunnel ranges from 181 m (600 ft) to 152 m (500 ft) in depth in the bedrock under Manhattan. The tunnel contract also includes the construction of nine new shafts, 161 m (530 ft) average depth, and the completion of a tenth shaft (the previously built construction shaft). The Manhattan Tunnel contract was awarded to the sole bidder Schiavone/Shea/Frontier Kemper Joint Venture (SSF) for $668,532,680.00, on January 31, 2005. The Manhattan Tunnel was designed ?in house? by the New York City Department of Environmental Protection (DEP) and the construction management was provided by a combined staff of the DEP and a joint venture of Jenny Engineering and URS.

Jan 1, 2008

By Z. Zhang, R. G. Reddy

Experimental and thermodynamic modelling studies on the structure of alkali borate melts and properties are discussed. A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of composition. A qualitative interpretation for the boron anomaly in viscosity has been proposed, which regards the boron anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosity of alkali borate melts increases or decreases according to the changes in rigidity and spatial connectivity of the glass network structure, which is the function of temperature and composition. These concepts with some key examples are discussed in relation to their usefulness and practicality in industrial slags. Keywords: alkali borate melts; structural model; activities; structural groups; viscosity;

Jan 1, 2004

By Pekka Taskinen

Advanced optimizing control of the fluidised bed zinc roaster has been in use for an extended period at Boliden Kokkola and the implications are seen as extended bed stability, increased throughput and far better on-line availability. The roaster furnace control system developed is based on a dynamic and predictive furnace model, with parameters determined experimentally at the site. The controller maximises the concentrate feed and keeps the furnace operational parameters inside limits given by raw material mix and equipment constraints. The products of a zinc roaster, calcine, sulphur dioxide and the side products, such as mercury, meet gradually more stringent requirements, in particular as to their assays and total recoveries in the process chain. The end users of sulphuric acid in northern Europe, among others in the pulp and paper industry, require mercury levels much less than the conventional 0.2-0.4 ppm Hg. Therefore, secondary de-mercurising circuits have been used over the last five years for further cleaning the SO2 stream allowing production acid grades with less than 0.08 ppm Hg.

Jan 1, 2008

By Browner R, Lincoln F. J

The activity of silver in solid gold-silver alloys (electrum) has been measured with an electrochemical concentration cell based on the super ionic conductor silver-i3-alumina in the temperature range 200 to 80oaC.The measurements of the silver activity in the range 0.5 to 90.0 atom per eent silver were found to be highly reproducible although there is some disagreement with an earlier study which used a similar technique. At temperatures above 400° the silver activity exhibits both positive and negative deviations from ideality in the silver rich region.This method suggests a simple technique for the nondestructive determination of silver in electrum alloys.

Jan 1, 1983

By L. T. Matthews, C. E. Loo

During sintering, porous ore particles are easily assimilated by liquid melt. Two simple models of the process are considered: the dissolution of a solid by a liquid and the penetration of a liquid into a porous solid. Laboratory sintering studies covering a range of experimental conditions were undertaken to characterise the assimilation of large particles of ore and flux by melts formed from different mixes of fines. For ores, the process appeared to be complicated by the detachment of fines from the ore surface prior to melt formation, according to the mass of adhering fines and surface roughness of the particle. This delayed the onset of assimilation and sometimes reduced it, although melt penetration was fast and effective. Studies using different temperature profiles suggested that the assimilation of haematite was controlled by the transport of Fe2O3 away from the surface of ore particles. The assimilation of limestone depended more on thermal conditions than on the three magnesia-bearing minerals considered. Changing the composition of the initial melt significantly altered the extent of assimilation of ores and limestone, but again had a less marked effect on the magnesia-bearing fluxes.

Jan 8, 1992

The use of solid state detector and radioisotope x-ray source for x-ray fluorescence analysis is illustrated by analysis for iron, copper, zinc, tin, and lead in about 700 samples taken from Australian mineral process streams. Limits of detection based on counting statistics (3 standard deviations) range from 0·001 to 0·004 per cent by weight element. The analysis accuracy was usualIy between 2 to 10 per cent (rms) of the mean element concentration and was determined by comparison with assays supplied by mineral companies. In most cases the main cause of error appears to be due to this assay and not the x-ray fluorescence technique.Some potential fields of application of solid state detector and radioisotope x-ray source for analyses in the mineral industry are indicated.

Jan 1, 1974

By Tapiwanashe Chenje, David Hewitt, Peter Radziszewski

"Steel media wear is a major cost component in mineral processing. In the case of existing operating mill, steel media wear prediction can be used to help compare the performance of steel media from different suppliers before completing marked ball tests. It can also be used to investigate how ores from different site of a given mine affect steel media wear. In the case of Greenfield cases, steel media wear prediction can be used to estimate the cost of steel media for a given feasibility study.This paper presents a wear testing and prediction methodology that ties together abrasion wear and corrosion wear testing results through the use of a simplified discrete element charge motion model. The experimentation dimension to this methodology takes samples for steel media, mine site ore and water to determine abrasive and corrosive wear parameters of a given media, ore, water set.The test methodology development is illustrated along with a comparison of wear predictions with observed wear rates in some operating mills. A case study is included that illustrates how this methodology was used to estimate steel media wear performance. The paper closes with a discussion on the use of parts of the experimental methodology to investigate other abrasive wear conditions such as liner wear, paste backfill piping and ore breakage as well as avenues for future test development.INTRODUCTIONThe cost of comminution processes represents a significant part of the overall costs of a mining operation. Grinding media/liner wear alone accounts for 15-25% of the total operating cost. The annual steel grinding media consumption is approximately 2.5 mtpa or 0.3% of total world steel production [Smorgon Steel Group, 2005]. Using an estimated grinding media cost of about US$0.75/kg [Halbe and Smolik, 2002], gives a media cost of over US$1.875 billion per annum. Mining continues to shift towards exploitation of lower grade ores as the higher grades get depleted. These low-grade ores require finer grinding for the liberation of the value minerals, and hence it can be assumed that grinding media consumption will also continue to rise.The Bond abrasion test, dating back to 1963, [Weiss, 1985] is still used to estimate the total mill media wear. This is a purely empirical test based on the ore. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2009

By J. Baird

The Sappington Bridge, a steel arch span bridge constructed in 1904 over the Meramec River, was demolished due to its advanced state of deterioration. The demolition was a project to benefit Crawford County, Missouri, the U.S. Army, the Missouri Department of Transportation, and the University of Missouri – Rolla (UMR) was conducted jointly by the UMR Rock Mechanics and Explosives Research Center (RMERC) and the UMR Center for Infrastructure Engineering Studies (CIES). By arrangement with Crawford County, a 55-foot span of the old bridge was brought to the University Structures Laboratory in Rolla, while the longer, 200-foot span of the bridge was demolished using preburning and explosives. Originally, the longer span was to be blown up by C Company of the 5th Engineer Battalion (from Ft. Leonard Wood, Missouri) under the supervision of personnel from UMR. Unfortunately, permission for the operation from the Department of the Army could not be obtained in time to meet permitting requirements for the demolition. Therefore, a commercial demolition contractor was employed to perform the demolition, and to remove the scrap.

Jan 1, 2003

By J. A. Meech, R. J. Tucker

"A dynamic computer model has been developed to simulate the operation of ore crushing plants. The model was created in a general form to allow imitation of a wide variety of secondary crushing circuits with only minor program modifications. The system can be run on either a microcomputer or a large time-sharing main frame computer as required.The size reduction and separation characteristics of crushers and screens are based on standard manufacturers' design and performance data. These calculations are isolated within various subroutines to facilitate tailoring of the model to emulate any particular plant of interest. Input and output data are presented in a variety of formats. Crusher, screen and conveyor amperages and surge bin levels can be presented in a tabular form along with appropriate alarms arising from improper circuit operation or process interruptions. Graphical representation of the circuit together with strip chart data output are features of the system when operated in a microcomputer environment.The program is currently being used at Queen's University as a teaching aid to demonstrate plant operating characteristics, control strategies and design concepts. The acceptance of, and reaction to the program at this level indicates a good potential for it to provide a valuable tool for operator training."

Jan 1, 1985

Anglo Platinum commenced commercial underground borehole radar (BHR) surveys during 2006 following a series of trial surveys using both the ?slimline? Geomole and Aardwolf systems. Current borehole radar systems comprise radio frequency transmitter ? receiver antennae operating at 30 -100MHz that measure the time taken for a transmitted pulse to traverse a rock volume and be received (Fig 1). The time taken can be converted to distance if the transmission speed of the pulse through the rock volume is known. The transmitted pulse may be reflected off a suitably orientated geological reflector (in reflection mode) or may be recorded in receivers located in other boreholes (cross-hole tomographic mode). In the Bushveld Complex lithologies, these radar systems have ranges of 30-50 metres in reflection mode depending on the electrical properties of local stratigraphic units. Both the Merensky Reef (MR) and the underlying UG2 have been shown to act as reflectors, which offer the opportunity of using BHR as an imaging or mapping tool. Reflection of the radar signal occurs wherever a strong contrast in dielectric constants occurs such as between norite and harzburgite or where chromitite stringers are present. [ ] Fig 1 Main elements of a borehole radar system Much experience has been gained in the practical application of BHR surveys in platinum mining. The value of a BHR survey is that it provides a continuous line of information to ?connect the dots? rather than a few discrete pierce points. BHR surveys can be used to mitigate risk in three crucial areas: ? Mine planning at the strategic as well as tactical level ? geotechnical evaluation of proposed shaft sites, detailed profiling or mapping of reef and disruptions of the reef such as faults, rolls and potholes; ? Mineral resource classification ? identification of structural discontinuities in orebodies affecting resource classification e.g. potholes and reef facies; ? Safety ? identifying areas with poor ground conditions that are often associated with faults, dykes and potholes.

Jan 1, 2007

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993

By Ovidiu Pasca

The Phelps Dodge Miami Smelter utilizes four Hoboken converters to process molten matte from the Isasmelt vessel. This paper presents past and present improvements in operation, maintenance and process optimization, based on data collection, which has led to increased converter campaign life and copper throughput.

Jan 1, 2005

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while