Search Documents

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By Thamiris Auxiliadora Gonçalves Martins, Isabela Falconi Brandolis Alves, Viviane Tavares de Moraes

Reverse flotation process is a method used for remove impurities from the most abundant iron ore; the itabirite. In this process, amines surfactant are used which may prevent the reuse of water in processes. The Fenton oxidative processes and the synthesis of nanoparticles are highlighted in catalysts application and in organic substances degradation. This study performed the synthesis of copper nanoparticles (CuNPs) to employ them as catalysts of the modified Fenton reaction to degrade an amine surfactant used in reverse flotation and compared with the classic Fenton (Fe2+) reaction. CuNPs were synthesized by chemical reduction, pH 11 with copper sulfate and ascorbic acid. They were characterized by UV-Vis, DRX and DLS and Zeta potential. The nanoparticles had diameters of 125.00 to 17.22nm and stability during 50 days. The tests were prepared with 180mg/L of amine and 1890mg/L of H2O2 in 150 minutes. The degradation was assessed by UV-Vis and FT IR. The results showed that CuNPs degraded 84% of the surfactant while Fe2+ reached 89%. In this way, both processes can be used for surfactant degradation, although the CuNPs method is easier to operate at neutral pH.

Oct 3, 2019

By D Craw

The Old Man Range, south of Alexandra, in central Otago consists of a package of highly folded greenschist facies schist of the Wanaka lithologic association. The range is crosscut by several east to ENE-striking high angle gold-bearing quartz veins, (eg Whites Reef and Grays Reef), which were extensively worked in the late 1800s. The range is bounded on its east side by the Old Man Fault, which separates these rocks from generally flat lying and planar Caples Terrane schist. To the west of the Old Man Fault, about halfway up the range, a large subparallel, 100 m wide fault zone strikes NNW and appears to cut off the historic veins. The fault zone consists of highly sheared and folded rocks and numerous high angle cataclasites and centimetre-scale clay gouge zones. Hydrothermal alteration is not apparent and the individual faults and shears are clay altered, possibly due to weathering, without visible quartz veins. Gold, limonite pseudomorphs after pyrite and rutile are concentrated in some of the narrow cataclasites and gouge zones. These mineralised structures are texturally similar to the gold-bearing reefs and may be structurally related. It is postulated that the NNW-striking shear zone and ENE-striking veins may be a conjugate array formed during a period of Cretaceous normal faulting.

Jan 1, 2004

By James F. Allan

"Abstract -The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec . Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by ? 0.10% Y203, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% Zr02. The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and cale-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and rninor britholite. Yttrium also occurs in britholite in cale-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By W. Geo. Waring

THE growing need of better methods for the recovery of zinc and other elements from complex sulfide ores has suggested an inquiry respecting a possible group separation of the elements by the aid of volatilization at more or less elevated temperatures. It 'is evident that if the zinc content of such ores can be completely separated, for instance, as pure oxide, by a volatilization 'method, there should be no difficulty in recovering the other elements by smelting and refining. Zinc burning" as applied to zinkiferous ores has advanced but little in practice since the invention of the wetherill grate-furnace process in 1852, as may be seen by reference to papers on the subject.' In other words the thermochemical reaction employed in effecting the volatilization of the zinc is essentially one of reduction by means of carbon, whether the ores treated contain their zinc in an oxidized form, or as the sulfide. The zinc vapors, liberated from the ores at a temperature above that required for the reduction of ZnO by C (about ,1100° C.) or for the volatilization of ZnS per se, (about' 1300°-1400° C.) are subsequently burned to ZnO or to ZnO + SOz, by contact with' atmospheric ,oxygen in the upper or posterior parts of the furnace chamber, or in a so-called "combustion chamber" after leaving the .furnace proper.

Jan 1, 1925

By Thomas Palangio, Blessing Taiwo

Image-based fragmentation analysis is increasingly utilized in blasting operations to evaluate particle size distribution in a non-intrusive and efficient manner. However, the accuracy of optical granulometry systems can vary significantly with particle size. Higher precision is typically achieved for larger fragments, generally those greater than golf ball size when using drone-based orthomosaic analysis. In contrast, the detection and delineation of fine particles become less reliable due to constraints such as pixel resolution, particle overlap, and partial burial within the muck pile. This variability does not undermine the value of image analysis but rather highlights the need for a deeper understanding of its operational thresholds and the integration of complementary methods or calibration approaches to improve its reliability across the entire particle size distribution. Technologies such as WipFrag, originally developed in the 1980s, are designed to conduct in-situ fragmentation analysis within complex blast environments, where fines are often obscured by larger fragments. The challenge becomes more significant in blast rounds exhibiting wide gradation ranges and increased fines, particularly resulting from excessive energy concentration in high-pressure zones near the borehole. Previously, this issue was addressed through methods such as analytical correction, zoom-merge correction, and empirical calibration using Rosin-Rammler and Swebrec distribution models. However, these traditional empirical calibration approaches, particularly those tied to distribution functions like Rosin-Rammler have shown limitations, especially in accurately representing the fine region of the fragmentation curve. In contrast, the recently developed xP-fan model, which incorporates the relationship between powder factor and fragment size, introduces the fragmentation energy fan principle which Kuz-Ram model does not entail. This paper presents a study on the application of the novel xP-fan calibration to enhance the accuracy of optical granulometry systems. The findings demonstrate how xP-fan help calibrate the fine region of the PSD without deflecting the maximum size.

Jan 26, 2026

By Frank L. Hess

Vanadium, although widely spread in minute quantities through the crust of the earth, is found in few places sufficiently concentrated to be economically mined and prepared for use. Most rocks carry from a trace to a few hundredths of a per cent of vanadium oxide, and coal ash may carry about as much as the rocks, Much of the "coal" quoted in the literature as carrying vanadium has been asphaltite, and in other ccal the vanadium is of late introduction. The ash of the petroleums, though usually present in very small quantity, may carry a large percentage of vanadiun, so that production of vanadium from it has been seriously considered. Naturally the ashes of soze asphaltites similarly carry vanadium.' The great deposit at Minasragra, Peru, to which further reference will be made, is probably an altered asphaltite. Ilmenite and cther iron minerals usually carry vanadium 10 and some has been saved from the minette ores of France. 11 Many veins that carry lead copper and zinc minerals also carry a little vanadium, which, especially if the veins are in a comparatively dry region, such as the southwestern United States, northern Mexico, Northern Rhodesia, Southwest Africa, or Spain, collects in the oxidized parts of the veins as vanadinite,

Apr 1, 1932

By T. Bednarski, T. McCallum, L. Moya, B. Gay

"Molybdenum recovery by solvent extraction has gained interest partly due to advances in concentrate leach technology. Historically, both molybdenum and rhenium have been produced using amine-based extractants with the ability to co-extract both metals. Alternatively, a phosphinic acid-based extractant (CYANEX® 600) can be used depending on the flow sheet. CYANEX® 600 selectively extracts Mo leaving Re in the raffinate, which is a valuable feature in plants which require rejection of the rhenium from the molybdenum circuit. CYANEX® 600 piloting results are reviewed and compared to commercial experiences with an amine-based extractant. INTRODUCTION Molybdenum is most commonly found as molybdenite (MoS2) in primary porphyry deposits (about 59% of global reserves) and copper porphyries (about 39% of molybdenum reserves)[1]. Recovery from molybdenite traditionally involves flotation (concentrates typically containing 85 – 95% MoS2) followed by roasting to produce MoO3. Solvent extraction is also used to recover molybdenum from acidic aqueous solutions resulting from scrubbing of roaster and smelter off gasses and leaching of molybdenite (uranium ores). Molybdenum is also frequently found in low concentrations in copper leach inventories[2]. More recently, pressure oxidation has gained interest to treat molybdenite concentrates. Molybdenum Chemistry The chemistry of molybdenum is complex with a series of extractable species existing dependent on the pH and oxidation state as shown in Figure 1.Under strongly basic conditions, molybdenum primarily exists as MoO42- while under strongly acidic conditions MoO22+ becomes the predominant species. In between, a number of isopolymolybdates such as Mo7O246- and Mo8O264- are dominant. Equations (1) – (3) demonstrate some of the proposed molybdenum equilibrium reactions[1]."

Jan 1, 2017

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

By Peter Fischer

A demonstration plant for QSL technology with a continuous through-put of up to 10 t/h concentrate has been in operation at the Berzelius smelter, Duisburg, Germany since early 1981. In the QSL-process, both oxidation and reduction steps are performed in a single horizontal long cylindrical reactor. In the present demo-reacior, 2.5 M diameter by 22 M long, these steps are separated by a low partition wall with an underflow opening, to prevent backmixing of slag. -Tests on a variety of concentrates, including high-lead Missouri-type material and lower grades, have shown recoveries and consumables indicating very attractive economics. Investment cost estimates further enhance the economic attractiveness. Environmental protection afforded by the QSL system is a major advantage. The process has proven its reliability and versatility and is now ready for commercialization. Continued test work, including smelting secondary lead materials, is planned.

Jan 1, 1983

Present roof bolting practices in the collieries of Australian Iron and Steel Pty. Ltd. are outlined. Roof support has been improved since introducing roof bolts and it is hoped to increase the reliability of the bolts still further.Expansion-shell, and split and wedge roof bolts five to eight feet long are placed by "Atlas Falcon" and "Fletcher" roof bolters. Both anchorage and tightening have presented some problems.Good panel supervision is required if systematic roof bolting is to be properly co-ordinated with coal production without unnecessary delay to either. Successful roof bolting can only be the product of conscientious men and supervisors who are all convinced of its value. A rigid operational code should be established early and maintained.INTRODUCTIONRoof bolting is a method of support which is permanent and reduces or eliminates the need for other support; The method was pioneered in America and was first experimentally investigated in Australian collieries at Elrington in 1949 (McKensey, 1953). Pneumatic installation methods were employed. Subsequently, a method of using standard hand-held electric coal drills was developed at John Darling Colliery (Horseman, 1954). Pneumatic roof bolting equipment was first operated in the collieries of Australian Ironand Steel Pty. Ltd (A.I. &. S.) in 1951. Since then various hydraulically operated mobile machines have been installed in Australian collieries and these, together with improved pneumatic equipment, form the two present basic methods of placing ,roof bolts. Roof bolt anchorage is achieved by either split and wedge or expansion-shell bolts.The two broad types of roof bolting are 1. consolidation of strata, and 2. suspension support.

Jan 1, 1961

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986

By J. G. Kim, B. G. Chae, D. S. Cheon, E. S. Park

The underground structures such as high-level radioactive waste disposal thermal energy storage should be designed and constructed considering thermal-mechanical characterization because of long term and/or cyclic thermal stress. High temperature changes in these structures can extend the existing cracks and generate new cracks in surrounding rock mass. In case of long term and/or cyclic thermal stress conditions, it is possible to lose the function of structures caused by the significant cracks and fracture growth in the rock mass. In this study, the critical thermal crack temperature of the granite, limestone and thermal Kaiser effect were evaluated. Experiments were carried out with the heating speed of 1.5?/min. To avoid thermal shock and target temperatures were set at 150? and 250?. In order to verify the thermal Kaiser effect, the samples were heated by 150 ? after 2-3 repetition to 250?. The generation and growth of cracks were observed through an acoustic emission measuring system. The variation of the physical rock properties was measured before and after thermal experiments. After compared with the thermal experiments using PFC2D, numerical simulations were carried out at higher temperatures (400?). The experiments showed that the initial thermal crack temperature of granite and limestone is about 35?, 32? and the critical thermal crack temperature were about 69? , and 49? , respectively. The experiments confirmed the thermal Kaiser effect of experimented granite and limestone due to thermal cyclic loading. From the numerical analysis, the critical crack temperature showed the same tendency as the thermal experiments. The P and S wave velocity of the sample after the experiment were reduced. Therefore, when heat is applied in long-term and repetitive conditions, these cracks may affect the function and stability of the underground structure. Therefore, further studies of thermal stress effects should be performed.

Jan 1, 2015

By R. E. Moore

The lining systems currently in use in BOF furnaces, certain steel ladles, and the slag line of electric are furnaces were developed during the late seventies through the mid-eighties using a trial and error method of combining aggregate, carbon sources, additives and binders. They are currently based on magnesia, graphite, metal additives and resin binders, the selections of each being tied to the anticipated intensity of the use conditions. The general functions of the respective constituents are well appreciated, however, there is still a great deal that is not known about how the socalled antioxidants protect the graphite nor how impurities from the graphite and the aggregate enter into the wear processes. In a simplified assessment of wear processes, it appears that if the deoxidized layer can be kept very thin, less than 810 mm in depth, and if the viscosity and quantity of the matrix glassy phases can be controlled to resist erosion of the deoxidized layer, lining life can be maximized for the various applications. This paper will discuss the characteristics of the starting materials systems currently being employed for applications requiring a deoxidation function to realize extended wear. It will not attempt to explain all the complex interrelationships between the respective constituents but will point to the potential for improvements through the use of improved constituents.

Jan 1, 1991

By John Nell, Paul den Hoed

Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and high-titania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes. Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites. A reaction mechanism is presented; where possible, its validity is demonstrated by the support of empirical observations.

Jan 1, 2003

By A D. Strand

The Coeur dÆAlene mining district in northern Idaho, USA is the second largest producer of silver in the world. The Proterozoic Revett Formation hosts most of the mesothermal Ag-Pb-Zn vein ore in the district; it consists of informally designated lower, middle, and upper members. All three members show up to an order of magnitude of southward thickening across the regionally significant Osburn fault. Changes in thickness of the Revett Formation across the Osburn fault reflect a major, down-to-the-south, crustal-scale fault that:was active during sedimentation, was periodically reactivated during the structural and metallogenic history of the district, and likely provided first-order control over regional fluid flow during mineralization events. Where vein structures intersect favourable strata, they produce rich ore; where vein structures cross unfavourable strata, they are poorly mineralised or barren. The most favourable host rock in the district is quartzite, which accounts for the large production from the quartzite-rich Revett Formation.The district has five main types of hydrothermal alteration:feldspar destruction, hydrothermal bleaching, carbonatisation, sulfidation, and silicification. Feldspar destruction is the most extensive and pervasive type of alteration, involving the district-wide absence of feldspar from Belt Supergroup rocks. Hydrothermal bleaching results from the destruction of hematite; it forms alteration envelopes that extend for tens to hundreds of metres into the wall rocks around many of the mineralised veins. Siderite alteration is most diagnostic of mineralisation, forming alteration envelopes that extend for tens to hundreds of metres into the wall rocks around all mineralised veins. Fine-grained arsenopyrite and/or fine-grained pyrite commonly form alteration zones adjacent to high-grade ore shoots that extend for metres to tens of metres into the wall rocks. Widespread silicification is most easily recognised by the presence of numerous quartz veins.

Jan 1, 2002

By T. Wallmach, S. B. Blancher, A. Delaporte, P. Goncalves

"Fe-Ti oxides concentrates produced from heavy mineral sand deposits are widely used for the production of titanium dioxide pigments that are critical components of white paint, plastics and paper. According to mining industry, the Fe-Ti concentrates mostly consists of three phases: ilmenite, leucoxene and rutile. However, a few mineralogical studies have shown that the variety of Fe-Ti oxides found in sand deposits is far more complex, mostly due to alteration processes. The aim of this contribution is to characterize in detail by means of Qemscan analyses the mineralogy of the three main concentrates (ilmenite, leucoxene and rutile) produced by the Grande Côte Operation (GCO) mineralurgical plant in Senegal. The ultimate goal is to characterize the different products and textures formed during the natural ilmenite alteration processes, to localize the phases carrying the main impurities (Cr and P), and finally to determine the physical properties of each mineral component to improve metal recoveries. Along alteration processes, Ti content increase. Ilmenite (FeTiO3) is progressively transformed into pseudorutile (Fe2Ti3O9) particles which could also be altered and transformed into hydroxylian pseudorutile [FeTi6O12(OH)3.3H2O] or complex blends of anatase microcrystals (TiO2). These transformations are accompanied by significant changes in particle textures. Microporosity and fractures appear and the impurity content also increases. Anatase rich microcrystal assemblages, so far described as Leucoxene, could be identified to consist of grains with higher porosities, water contents and higher intrapore impurities. These particles are the main carriers of chromium and phosphorus. The observed mineral transition textures have a significant impact on the ore dressing processes. During these transformations, the physical properties of these phases change, the magnetic susceptibility as well as densities decreases, due to the increase in porosity. The separation of particles, especially those with high porosity will help improving the GCO mineralurgical plant performance and to reduce the impurity contents in finals products."

Jan 1, 2018