Search Documents

By E. J. ENGEL

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Grenville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New York State include earth materials of differ- ent chemical and mineral compositions. In general the mineral talc is sub- ordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits.

Jan 1, 1949

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By S Henderson

The Otago Goldfield has produced approximately 8 million ounces of alluvial gold and over 2.5 million ounces of hard rock gold and is currently home to New ZealandÆs largest producing gold mine. In the eyes of explorers this production history makes the goldfield a good place to explore.   Modern exploration in the Otago Goldfield commenced in the late 1970s with the exploration for tungsten. However, a rapid rise of the gold price in the early 1980s saw the focus shift to the exploration for gold which lead to the discovery of the Macraes Gold Project in 1984, which since it came into production in 1990 has been New ZealandÆs largest producing gold mine. With the exception of the Macraes Gold Project, exploration continued in the Otago Goldfield for a further 20 years without further success.   In 2006, Glass Earth (NZ) Limited (Glass Earth) reviewed all the exploration technologies applied to the Otago region and available geological data, including the 1996 OceanaGold Helicopter Electro-Magnetic (HEM) data, and concluded that combined magnetics and HEM were able to delineate the Hyde Macraes Shear Zone (HMSZ) which hosts the Macraes Gold Project. Unlike previous explorers who explored the Otago region in a piecemeal manner, Glass Earth opted to collect a new, region-wide dataset which could be integrated with all previous collected geological information to come up with new exploration concepts and targets. As part of this process, Glass Earth applied in mid 2006 for New ZealandÆs largest on-shore gold Prospecting Permit, PP39-322 which was subsequently granted in November 2006. In mid January 2007, Glass Earth commenced acquisition of approximately 50 000 line kilometres of HEM data, making the Otago regional aerial geophysical survey (survey) the largest aerial geophysical survey ever undertaken in New Zealand.   This paper will report on the progress of the Otago Regional aerial geophysical survey and outline some of the preliminary findings from what is still a work in progress.

Jan 1, 2007

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By Dan Brunner, Scott Thomson, Ben Lyddall, Duncan Thomson

Geosensing is used in oilfield drilling in conjunction with geophysical tools to support characterization of rock properties, geology, and reservoir conditions. This technology is now available to the mining industry and has been successfully applied to underground in-seam directional drilling in Australian coal mines for geologic exploration and methane drainage. The system utilizes a range of drill rig and wellhead mounted sensors which, combined with analytical software, produce real-time data from which 3D spatial features can be accurately modelled significantly in advance of mining. This innovation greatly expands on the information obtained from current in-seam directional drilling practices and provides for improved characterization of coal seams, including soft and weak zones, locations of geologic discontinuities, and analysis of formation flow. This paper provides a description of the geosensing system and the interpretation of actual data from long in-seam directionally drilled methane drainage boreholes at mines in Australia, and discusses how this system increases the value of directional drilling as an exploration tool for the coal mining sector, and the evaporite and hard-rock mining sectors where directional drilling is also applied.

Feb 1, 2024

By E. C. Westman, W. R. Thomas, W. J. Conrad, A. J. R. Russell

"Understanding ground control problems continues to remain a focus of the mining engineering community. To aid mine operators and engineers in identifying and responding to ground control issues, the Ground Observation System (GOS) is being developed. The GOS is an integrated, web-based graphical user interface that displays ground response data collected wirelessly from an underground mine. It presents data in an intuitive manner to assist mine personnel, who are on- or off-site, in quickly identifying hazardous areas. Geotechnical instrumentation will be connected to wireless transmitters that will relay data in real-time to a surface computer that stores the information in a database. The GOS website will then display the geotechnical data in graphical and tabular forms, as well as in conditionally formatted mine maps. Data from each measurement device will be able to be viewed in its entirety or within a time interval, and can be downloaded for further analysis. The ability of the GOS to quickly interpret and communicate mine hazards to personnel of varying technical ability should prove to be a useful tool in understanding ground control and thus improving mine safety.INTRODUCTION Computer-based data information centers that convey operating parameters and conditions are prevalent in modern underground mines. Today’s systems are popular in showing ventilation controls and monitoring equipment performance (Jyothi & Meena 2013). In ground control monitoring, Conover, Ross, and Bigby, 2010 have installed a wired telltale roof monitoring system that sends roof displacement data every ten minutes to a computer on the surface. The computer receives, stores, and displays the data in real time. Data can also be viewed remotely through a password protected internet connection. Additionally, an internet connection allowed for remote updates to the system which streamlined software development and maintenance by eliminating travel (Conover et al., 2010). Currently, no such system beyond Conover et al.’s design has been accomplished. The Ground Observation System (GOS) is being developed to fill the void of real-time geotechnical monitoring in underground mines. A wide array of data will be transmitted wirelessly and broadcasted to on- and off-site mine personnel through the internet. The GOS will incorporate geotechnical data from roof deformation, borehole scratch testing, photogrammetry, and seismic monitoring into one interface, all while achieving permissibility for the use in gaseous mines. As a result, a comprehensive view of rock movement due to mining will be available. The overall purpose of the GOS is to deliver warnings; to ensure reliable data is relayed to personnel for the identification of potential ground failures, provide mine engineers information to design more stable mines, and assist with further geotechnical research."

Jan 1, 2015

By G. I. Mathieu

Research and development studies were carried out at the Canada Centre for Mineral and Energy Technology to produce a synthetic forsterite sand from asbestos tailings for Les Sables Olimag Inc. The National Research Council of Canada also supported and collaborated to the project. Theoretically, the technological approach consists of a heat at over 1300°C; however, the process without additive would result in the production of an enstatite-rich product (MgSiO3) having a fusion temperature less than 1600°C. The purpose was to foster the formation of forsterite (Mg2SiO4), a more refractory compound. The fabrication of the forsterite product requires pre-agglomeration of serpentine-MgO with a binder, which is stable at high temperature, to prevent the loss of the powdered magnesium oxide as dust in the kiln off gases and to maintain the mixture homogeneous during the process. Characterization of the end products with respect to mineral composition and thermal resistance are described. The synthetic forsterite in sand form was tested with success under a bath of liquid steel maintained at 1700°C for up to two hours. The advantages of the new sand and its potential applications will be reviewed.

Jan 1, 1992

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By E. Pallumbo, N. Szwedska, R. Asselin

"This paper highlights the results of collaboration between geology, mining and mineral processing teams during the restart of the North American Lithium Project, located near La Corne, Quebec, Canada. This collaboration was central in ensuring a cross discipline harmonization of design parameters and key inputs, all of which allowed for the development of an optimized life of mine plan suited to the particular needs of the operation.INTRODUCTION In July 2016, North American Lithium Inc. (NAL) began the process of restarting operations at the former Quebec Lithium Mine, located in the municipality of La Corne, Quebec, Canada. The North American Lithium Project (the Project) as it is known today, is the latest chapter in the history of this property. In order to provide a robust foundation for the project, multidisciplinary collaboration was instituted between the geology, mining and metallurgy teams. Despite the intrinsic link between these departments, in many instances their work is completed separate from one another; in silos. This collaboration highlighted specific drivers in the mining value chain that could be exploited to ensure that a saleable product could be produced effectively. This paper explores some of the concepts and strategies that were developed during the feasibility study that supported the project restart (excerpts from the study technical report have been used throughout this paper). PROJECT HISTORY In 1942, prospectors identified the presence of numerous spodumene-bearing pegmatite dykes on the Property. This led to additional interest and exploration drilling campaigns. In 1955, Quebec Lithium Corp. (QLC), who had acquired the property, began construction of an underground mine with mill facilities located on the surface. Operations began the following year at a production rate of 1,100 tonnes per day. A historical cross-section view of the underground mine is shown in Figure 1. In 1959, QLC began the construction of an on-site lithium refinery to produce lithium hydroxide. The refinery was finally operational by 1963. Mining and processing operations continued until 1966 when activities were halted due to a labour dispute. The property was sold and a few years later attempts to resume production were unsuccessful. Property ownership changed several times again until being acquired by Cambior in 1987. In the early 1990’s the existing mine and mill facilities were sold and the mine site rehabilitated"

Jan 1, 2019

By Pati±o A

The Argentine pyroclastic loess arevulcanogenic deposits, which have their sources in the circumnpacific rim. The object of this work is to realize a de-tailed mineralogical characterization of this sediments, to use it like a geo logic outline which regiters discordance or similarity in them, The sampling zone extend from 714N-4125 to 622W-339S. The descriptions of these sediments was considered like basic, mesobasic or acid rocks. The basic sediments, looking like andesite-basaltic composition, are fill-ing the andean valley. The mesobasic one have a similar composition with a pyro-clastic dacite rock, and have been found in marshy pleistocene sediments in the intermountain valley and in the pampeana prairies. The acid ashed conform rhyoda-cite-rhyolite sediments which form the pampeana loess covers in the prairie.

Jan 1, 1990

By Zhihao Yue, Honglie Shen, Yahui Teng, Ye Jiang

"In this paper, manganous nitrate [Mn(NO3)z] was used to assist the etching of silicon wafer in hydrofluoric acid (HF) for the antireflective application, and alumina (Al2O3) layer was deposited on the surface of the etched sample by atomic layer deposition method for further antireflection. The surface morphological and compositional studies of these samples were performed by scanning electron microscopy attached with an energy-dispersive X-ray spectrometer. The surface reflectance measurements were carried out using UV-Vis-NIR spectrophotometer. Binary structures of pyramids and nanopores were obtained by etching the alkaline textured monocrystalline silicon wafer in HF and Mn(NO3)z mixed solution for not more than 15 min. But excessive increase of etching time of up to 30 min resulted in the whole destruction of pyramids. The average reflectances of the 5-min-etched sample before and after being coated with 75-nm-thick Al2O3 layer are 4.62% and 3.47% in the range of 200-1000 nm, respectively.1. IntroductionAs we know, the reflectance of silicon wafer after being sliced is so high that the maximal photoelectric conversion efficiency of silicon based solar cells is limited. Therefore, alkaline texturization process was used for silicon solar cell in industrial production. But the reflectance of this alkaline textured wafer is still greater than 10% and this process can only be used for monocrystalline silicon solar cell."

Jan 1, 2013

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner's pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world's supply of the' material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity'of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By M. Piche

The western part of the Hauy Formation of the Opemisca Group, occurring near the town of Chapais, is described in this paper. As it has been defined previously, the Formation is composed of a succession of subaerial andesi tic lava flows with some interbedded proximal volcaniclastic sediments. Towards the East, these volcanics yield to coarse grained fluviatile sediments having similar composition to the interbedded lavas. Further east, the composition of these sediments is more arkosic with dioritic and tonalitic fragments. It is proposed that these arkosic sediments are a part of the Stella Formation which has been described by Dimroth et al. (1982).

Jan 1, 1984

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Xuefeng She, Qingguo Xue, Jingsong Wang, Guang Wang

Iron nugget could be got at high temperature using carbon composite pellet, which were made by the mixture of ludwigite and reducing agent. In order to reduce sulfur content in the nugget, effects of additives on the desulfurization was investigated. The sulfur content could be dramatically reduced if the CaO was introduced into the pellet and the sulfur content was as low as 0.046wt.% when the addition amount of CaO was 5wt.%. However, the melting separation of pellet became increasingly difficult and the yield of iron decreased when CaO content in the pellet gradually increased. Na2CO3 could also reduce the sulfur content in the iron nugget and made the iron and slag separate difficultly as well. When 6wt.% Na2CO3 was added into the pellet, the pellet was too difficult to melt separation and the sulfur content in the nugget was 0.084wt.%, which didn’t meet the need of steel making.

Jan 1, 2015

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By G R. Ballantyne, M S. Powell

A comprehensive Australia-wide survey of comminution energy consumption at copper and gold mines was presented by the authors at the 11th AusIMM Mill Operators’ Conference 2012. The database has been extended to include major overseas mines and used to benchmark comminution energy consumption across the industry. The mines included in this study now represent 15 and 24 per cent of the total global gold and copper production respectively, and almost all Australian production. The comminution energy intensity per unit of saleable metal has been presented in a graphical form similar to a cost curve used in economics. The graphical method has been developed to assess the competitive advantage that can be achieved by reducing comminution energy intensity.This benchmarking tool has been applied to three published case studies to assess its applicability. The first case study indicated that a large reduction in size-specific energy (kWh/t -75 µm) was achievable by converting standard semi-autogenous and ball mill circuits to include high pressure grinding roll and stirred mills. The second case study investigated the metal-specific energy reduction historically achieved by Bougainville with the addition of a preconcentration screening plant. The final case study was conducted by Barrick Gold Corporation and involved incremental efficiency upgrades at three of its gold mines: Cortez, Cowal and Mara North. The application of the benchmarking tool to each of these case studies successfully demonstrated the scale and competitive advantage that was achieved by reducing energy intensity.CITATION:Ballantyne, G R and Powell, M S, 2014. Benchmarking comminution energy consumption for improved efficiency, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By McHenry Mosier

The Anson Bette manganese mine, with two prominent manganese-bearing outcrops in schist, has attracted considerable attention for its variety of manganese minerals and its possibilities as a potential source of manganese. Little mining was done prior to 1925, when the present owner acquired the property, and operations since that date have been intermittent. Mine workings are open cuts with a maximum depth of 35 feet. The two outcropping ore deposits are irregular, pipelike bodies about 500 feet apart. As nothing was known of the grade or extent of mineralization in depth, four holes totaling 1,072.5 feet of bore Were diamond-drilled by the Bureau of Mines in the summer of 1943, with the results shown in figures 3 to 6. In.1945 a geophysical survey was run to map the magnetic anomalies in the manganese-bearing belt as a means of determining the locations of manganese deposits. Positive correlation of magnetite and manganese ore was not obtained.

Jan 1, 1949

By Huimin Lu, Lian Zhou, Panpan Wang

"For the low concentration C02 exhaust gas from coal-fired power plant, steel plant emission trapping and recycle problem, a pressure swing adsorption process was studied, using a porous imidazolate framework materials (ZIFs) as adsorbent, separating carbon dioxide from fuel gas mixture. In the carbon dioxide reduction condition by electrochemical method, using ionic liquids as electrolyte, the oxygen and carbon products could be obtained, including carbon nanotube, nano carbon fiber and amorphous carbon. At last, a new C02 collection, recycling and reuse technology was formed.IntroductionDuring the combustion of fossil fuel in coal-fired power plant or steel plant, large amount of carbon dioxide has continuously emitted into the atmosphere. The phenomenon has resulted in the melt of arctic glacier and the frequent emergence of abnormal climate. How to reduce the emission of carbon dioxide and protect human living environment has become a worldwide challenge. Recently, there are three routes to resolve this problem: The first one is to adjust the energy structure and develop new energy, such as solar, wind, hydrogen; the second one is to improve energy efficiency and avoid waste; the third one is to research capture and sequestration of carbon dioxide (CCS). But many researchers have come to realize that the recovery and utilization of carbon dioxide are more important than the sequestration of it. Because the captured carbon dioxide just buried under the earth maybe cause secondary pollution if carbon dioxide leak out from the adsorbent."

Jan 1, 2013

By Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003