Search Documents

By Cloutier JY, Quinn P, LeClerc A, Dube G, Agar GE

Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer. The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared with a readily available but under utilised method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate.

Jan 1, 1993

By I. Barin

The thermodynamics of cyclone smelting of sulphidic copper ores is described using as example the production of copper matte with 75 wt % Cu. Equilibrium calcualtions and material and energy balances show that an increase in process temperature from 1600 K to 1900 K results in the extensive transfer of minor elements such as As, Sb, Bi, Pb, Zn,.... to the gas phase. A pilot plant for carrying out the cyclone smelting process is described. Calculations of material and heat transfer for the reaction of ZnS show that the smelting reactions of sulphides in the cyclone take place very rapidly at high temperatures. The dissociation of the sulphides with subsequent oxidation reactions in the gas phase plays an important part in. the process and is mainly controlled by heat transfer.

Jan 1, 1983

By Ray Holmes

This paper describes one approach in our search for greater stope efficiency and lower costs. The uppers technique with wagon drills in cut-and-fill stopes was commenced, on an experimental basis, in our Sudbury mines in 1961. To date, the method has developed into an accept-ed production operation. This technique minimizes the intermittent aspects of the drilling, blasting, mucking and filling operations associated with other cut-and-fill methods. However, studies show that not all cut-and-fill stopes are suitable for uppers, the governing factors being ore width, dip of the orebody, and ground conditions where large areas of unsupported back remain stable for ex-tended periods of time until rockbolting can be accomplished. Introduction F ALCONBRIDGE Nickel Mines Limited operates seven mines within a radius of 30 miles of the city of Sudbury, Ontario. These mines extend in depth from 1,500 to 6,300 ft. The ore consists of brecciated, massive and disseminated sulphides, and the ore minerals consist primarily of pentlandite, pyrrhotite and chalcopyrite. Widths are generally irregular and vary up to 150 ft. The ore dips at between 35 and 90 degrees.

Jan 1, 1965

By D. Harrington

The primary objective of this paper is to discuss the hazards and furnish a list of recommendations for the safe operation of quarries and related works. They have been compiled from Bureau of Mines publications covering the safety experience of engineers before and during the year in the mineral industry,5 from a publication of the National Safety Council, Inc.,6 from explosives recommendations made by various explosives manufacturers,7 and from suggestions obtained from quarries visited. The second objective is to describe and illustrate safety devices, practices, and quarrying methods. The quarrying and related industries of the United States had a lower accident-frequency rate than either the metal- or coal-mining industry as reported for 1942.8 However, the quarry industry ranked eleventh in 15 major industries during 1942 in lost-time accident fre¬quency; metal mining ranked fourteenth and coal mining fifteenth.

Jan 1, 1950

THE object of this paper is to offer some suggestions to assist metallurgists to supervise the operations of flotation plants. We do not yet thoroughly understand what "flotation" is or "why minerals float" and all attempts that have been made to explain the phenomena have been based on theory or imagination, and have not been capable of substantiation by practical demonstration, or even by laboratory tests; but it is wellknown that particular minerals will float in a liquid under certain specified conditions, and that some other minerals will not float under those conditions, and that, if a mixture of the two classes of minerals be subjected to those conditions, there will be separation of the minerals, of which one class will float and the other will remain unfloated as a residue. The duty of the flotation expert is to so control the operations and the conditions of the liquor as to obtain the best commercial result from the ore he is treating. The chief controlling factors in a flotation plant appear to fall under the following eight headings, all of which are important:1. Crushing.2. Rate and regularity of feed.3. Density of pulp.4. Temperature.5. Addition agents.6. Condition of circuit liquor.7. Agitation.8. Aeration.

Jan 1, 1920

By B. K. Blashich

In responding to mine fires and explosions, accurate and timely analysis of the mine atmosphere is critical in making decisions regarding firefighting, mine rescue and mine recovery operations. For many years instantaneous analyses were available to rescue workers using handheld or portable gas detection equipment, including infrared, electrochemical, or catalytic measuring devices for a limited number of specific gases such as oxygen, methane, carbon monoxide and carbon dioxide. Instantaneous sensing technology is not available for all gases, such as nitrogen and hydrocarbons, found in a mine fire atmosphere and cross-sensitivity can be a problem with this technology. For these reasons, air samples are collected for injection into a gas chromatograph for a complete and accurate analysis for all gases including oxygen, nitrogen, methane, carbon monoxide and carbon dioxide, as well as ?fire gases? such as hydrogen, ethylene, ethane, and acetylene. This method requires additional time for transporting the samples to the laboratory near the mine, as well as an instrument operator to inject the samples for analysis. The use of a portable micro gas chromatograph with a continuous and automatic injection system has been implemented by the Mine Safety and Health Administration (MSHA) during mine recovery operations. The device directly samples the mine atmosphere from an underground location every twelve minutes and automatically analyzes the samples for all of the mine fire gases. The portable unit utilizes micro technology and the operating software has been modified to perform the calculation of sample results in and Excel® spreadsheet without user interaction. This paper describes the micro gas chromatograph system and its use at a recent mine recovery operation. The automated remote operation of the micro gas chromatograph has been shown to be a good alternative to infrared and electrochemical sensors used for mine atmosphere analysis.

Jan 1, 2009

By M. Arvola, A. Mäkinen, N. Isomäki

Arsenic is a compound that has no significant market value. However, it needs to be removed from ores, concentrates and other process streams because of environmental or technical processing concerns. A wide range of arsenic containing minerals exists in nature, and in many instances these minerals are also associated with the ones that have commercial value. For example, sulfide copper ores are normally closely associated with minerals like enargite, Cu3AsS4 and tennantite Cu12As4S13. After mineral processing these arsenic sources can report to the waste waters and these effluents need to be treated before discharge or recycling. Ferric arsenate precipitation is a well-established method for stabilizing arsenic in effluents. Electrochemical arsenic removal utilizes the same adsorption/precipitation ideology as ferric arsenate precipitation. Electrochemical arsenic removal, even though it is a simple process in terms of equipment, is a complex system involving chemical and physical mechanisms taking place simultaneously to remove dissolved and/or solid arsenic components from wastewaters. The whole process can be described by the following three steps: 1) electrolytic oxidation at a sacrificial anode (dissolving electrode metal, iron for example), 2) chemical reaction between dissolved iron and arsenic to form a solid precipitate and 3) aggregation of the particles to form flocs, which can be removed by known solid/liquid separation methods. Electrochemical arsenic removal is a very efficient way to remove arsenic from different waters to very low residual concentrations.

Jan 1, 2016

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By Takashi Furuyama, Sukeyuki Mori, Abel Bissombolo

"In flotation practice, a good recovery of minerals largely depends on the degree to which the valuable minerals have been liberated from the associated gangue during the grinding process. Therefore, a regular measurement of the degree of liberation can provide data for the assessment of the quality of separation and predicts the effect of changes in the grinding-classifying circuit on flotation process. Generally, the standard procedure for measuring the degree of liberation requires the preparation of polished sections - a time consuming operation that also has the disadvantage of providing an overestimated number of free particles because of the stereological nature of produced samples.The present work is an alternative approach to avoid these miscalculations and establish a system of control for fluorite flotation plants. The system deals no only with the state of liberation but also the dynamic behavior of individuals particles and mineral components within the grinding-classifying and flotation circuits. It involves methods such as sieving, x-ray diffraction analysis, study of polished sections and microscopic counting of preliminarily sieved minerals particles from a fluorite processing plant, randomly dispersed on a glass slide, but not embedded in a resin mounting medium. If a complete information on the textural properties of minerals in the ore (including its mineral components distribution) can be obtained through x-ray diffraction analysis and study of polished sections, the microscopic counting is used to determinate with enough accuracy the mineral liberation, estimate the grade of fluorite ore and products, determinate the deportment and approximate recovery of individuals particles and mineral components within the investigated circuit. For a count of 100-1000 particles in each n-size range, the counting method was found to be a particularly reliable and less time consuming operation that could substitute the chemical analysis of fluorite ore for an estimate of the grade:"

Jan 1, 2003

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

Gold rush histories are usually written as though they were unique events in the development of a region or nation. While this is a valid way of looking at gold rushes, it is not the only way. This paper is a brief attempt to relate the West Coast rushes to a wider context. During the second half of the nineteenth century the lure of gold transformed the Pacific Rim. Gold rushes drew more than half a million Europeans and Americans to lands bordering the Pacific. By 1900 a chain of mining, industrial and urban centres ran from California to Alaska; from Ballarat to New Guinea, and on to Western Australia. The New Zealand rushes were a significant chapter in this story. People, cargo and information passed from rush to rush. Techniques learned on earlier goldfields were imported; those developed in New Zealand were, in turn, taken up elsewhere. Administrative systems and regulations developed in Australia were implemented in New Zealand, improved and passed on to Canada. This interconnectedness was so strong that gold-seekers thought of the mining regions as a distinct culture, 'the whole digging world'. Much can be made of the similarities shared by rushes. But comparison can also highlight the individuality of each rush. +The early days of the West Coast rushes were perhaps the strongest assertion of a diggers' culture. A brief period in which a remarkable orderliness was created through mateship, self-regulation, and the occasional threat of rough justice. The West Coast rushes were both a unique experience and an integral part of a process which transformed the Pacific Rim during the nineteenth century. Understanding their part in that bigger story highlights just how unique they were.

Jan 1, 1996

By Eugene Nel, Johan Theron, Chris Martin, Hans Raabe

"Impala Platinum Limited is the world’s second largest platinum producer, producing more than 1.7 million ounces of the precious metal last year, much of this from the UG-2 reef located in the Bushveld Complex, South Africa. As part of Impala’s ongoing expansion programme, tonnage through their principal UG-2 processing facility, near Rustenburg, was increased 40% in 2001.To accommodate the increased throughput, the role of the existing primary mills was converted from conventional semi-autogenous grinding units, to attrition and selective grinding units, operating in fully autogenous mode. The finer chromite and coarser silicate components in the mill discharge are then separated by screening and processed in dedicated circuits downstream. This way, the need to spend considerable capital to increase primary grinding capacity was averted.In the last year, considerable work has been conducted to evaluate and optimise the two downstream circuits. This has involved an optimisation programme of sampling and diagnostic flotation testing, supported with QemSCAN analysis. This paper will describe the operation of the new circuit. It will also describe some of the more novel aspects and interesting findings from the optimisation programme.INTRODUCTIONThe South African platinum industry is the world’s largest producer of platinum and the world’s second largest producer of palladium. Located in a wide area north of Johannesburg, the industry mines ores from the Bushveld Complex, one of the world’s great mineral treasure chests, containing over 70 percent of the world’s platinum, as well as extensive reserves of the other PGE (platinum group elements), chrome, manganese and vanadium. The industry employs about 180,000 people in, predominantly, underground mines, which together form an almost unbroken circle of mining operations 200 km in diameter."

Jan 1, 2004

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

A particle-bubble collision model was used to investigate the minimum recovery zone height, H(r,min) required for flotation columns. The criterion used to define H(r,min) is that height which gives unit collision probability. It is shown that H(r,min) is determined by particle and bubble size, gas hold-up and bubble-bubble interaction. Under typical operating conditions, for flotation of particles less that 10 micrometres in size H(r,min) is greater than 10 m, but it reduces to less than 1 m for particles greater than 100 micrometres

Aug 1, 1995

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

By Gil Espejo, Denise Duncan

"In Alberta, several initiatives are under way to form partnerships between educators and industry to work together in preparing a skilled and technically competent workforce for the future. One successful initiative is the Teachers in Business program which provides high school teachers one month paid internships in Alberta businesses. Initiated by the Science Alberta Foundation in 1992, this program has offered participating teachers a variety of work experiences and job shadowing tours in industry.A Growing Need of Education and Industry PartnershipsIn our ever evolving world, industry is in a tight race to keep up to date with new technology and to remain competitive. Industry is relying on the education system to provide them with the core base for their future workforce. To accomplish this, the education system needs the support of industry to develop the right focus to prepare its students for the race. What skills will our future workforce need? How can we best prepare our students for these needs?Teaching the latest in technology, especially at the high school level, is a major challenge. It is difficult for educators to keep abreast of the rapid changes in technology. High school graduates need exposure to the latest advancements. And so do their teachers. Students must be prepared to adapt to the challenges of the future, Le. global competition, rapid technological change and an expanding knowledge base."

Jan 1, 1995

By V. P. Mehrotra, D. W. Fuerstenau, A. -Z. M. Abouzeid

The use of pulverized coal for electric power generation results in the production of vast amounts of fly ash. One potential use for waste fly ash is the production of pellets for lightweight aggregates. This paper is concerned with the role of the physical and chemical characteristics of two different fly ashes in governing their agglomeration or pelletization behavior and their strength characteristics. In batch balling experiments, fly ash pellet growth was found to be extremely sensitive to the amount of moisture added. One ash (Mohave) exhibits marked pozzolanic activity whereas the other (Jim Bridger) does not. The pozzolanic activity has a very pronounced effect on pellet growth kinetics, moisture requirements, and the effect of various additives on growth kinetics. Slow drying under ambient conditions produces strong pellets from Mohave ash whereas Jim Bridger ash pellets lacking in pozzolanic activity are weak. Rapid drying at high temperatures results in weak pellets because water necessary for hardening is driven out of the pellet. Steam curing enhances pellet strength. Locked-cycle pelletizing experiments exhibit expected oscillation in pellet production rates and attendant fluctuations in pellet green strength.

Jan 1, 2004

By Charles L. Kimbell

In overall aggregate, the world's mineral industry in 1987 experienced a more satisfactory year than in 1986, at least insofar as its performance could be assessed from traditional statistical indicators. Production, trade and consumption seemingly advanced in the case of the majority of commodities, and prices for a number of commodities advanced. It was by no means certain, however, whether 1987 investment in mineral industry ventures would top the levels of 1986, when, in the case of petroleum industry investment expenditures there had been a sharp decline, this in contrast to evidences of a slight upturn in steel industry investment. World crude mineral output value was estimated at more than $1,084 billion, and the value added by minerals industry processing of this material probably raised the total value of the industry's production from primary materials to more than $2,600 billion constant 1983 dollars. Less easy too assess was the value of mineral commodities moving in international trade, but with a resurgence in oil prices from the 1986 levels, an increase above the 1986 $500 billion mark seemed assured. There are no comprehensive aggregate statistics on mineral consumption comparable to those on production and trade, but quantitative growth recorded for most major commodities suggested a favorable trend, particularly when coupled with a general (though by no means universal) upturn in unit prices.

Jan 1, 1989

By J. Brent Hiskey, Rebecca Grace Copp

The solvent extraction of yttrium and neodymium from copper pregnant leach solutions (PLS) using Primene JM-T, a primary aliphatic amine, has been studied. Effect of contact time, pH, sulfate concentration, and extractant concentration were investigated using synthetic and actual PLS systems. Standard experimental conditions were 5 minute contact time, pH ~2.5, and 10 % v/v Primene JM-T concentration. Distribution isotherms were constructed for the pure systems and for actual copper leach solutions. Synthetic solutions contained 100 ppm Y and ~75 ppm Nd. Samples of PLS contained 2 - 10 ppm Nd and 14 - 30 ppm Y. Results showed that complete extraction of both yttrium and neodymium occurred within five minutes and at pH values greater than 1. It was also found that sulfate concentration does not inhibit extraction at any concentration. Additionally, the distribution isotherms created show that extraction for these metals can operationally take place in one stage.

Jan 1, 2016

The Taupo Volcanic Zone inNew Zealand and the Philippine Mobile Belt in the Philippines are characterized by active subduction, active volcanism and high seismicity. The main factors affecting characteristics of geothermal systems in both countries are: tectonic setting, source magmas, maturity of the systems, and depth to the degassing magma body. Within New Zealand, geothermal systems are grouped into arc- and rift-type. Fluids in arc-type systems contain high amounts of volatiles (<20%), with high CO2/Cl, CO2/He, and N2/Ar ratios. Mantle-type volatiles predominate in rift-type systems. Philippine geothermal systems are largely arc-type, the topography is rugged, leading to the separation of water and vapour upflows, as opposed to the overlap found in New Zealand. The relatively shallow depths of degassing magma bodies in the Philippines results in steeper geochemical gradients, leading to higher proportions of arc-type magmatic water (>40%) and higher Cl contents (3000 - 10 000 mg/kg), Maximum temperatures are also higher, reaching up to >400¦C. Arc-type alteration assemblages in New Zealand and the Philippines are similar. Because Philippine geothermal systems are less mature, have higher temperatures and steeper geochemical gradients than New Zealand ones, advanced argillization is more widespread occurring down to depths of 2000 m. Mineral phases are more varied due to the active input of magmatic waters and the formation of vapor conditions at depth, forming P04-, B-, Li-, Ce-, F-, and Cl-bearing minerals at high temperatures. In the Philippines, high temperature magmatic-hydrothermal to contact metamorphic assemblages containing biotite, amphiboles and pyroxenes are relatively common, but rare in New Zealand.

Jan 1, 1995