Search Documents

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009

By R. G. Hamm

A brief outline covering the shovels and draglines in use in the open-pit mines of Western Canada, including British Columbia, Alberta and the Yukon, is given, followed by the procedure for the selection of the correct wire rope for each application. Such fa ctors as wire rope constructions, lay directions and types of cores are mentioned. Once the correct wire rope has been selected, there are variousfactors that can affect the service fife ofthe rope and the reduction ofdown-time during rope change-overs. Factors such as hairpin winding, types of Becket loops, and shovel drum and bail adaptors are described.

Jan 1, 1979

By Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Ahmet Varol, Ertugrul Kaya, Turgay Ozat

This paper presents analysis of environmental effects induced by cautious blasting during the construction of the Istanbul Subway 4 Levent - Ayazaga Darulsafaka Metro Tunnel Project carried out by the contractor, located at Northern Istanbul in Turkey. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S6-7-8 shafts of this tunnel route, ground vibration components were measured carefully by using five vibration monitors during the construction of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighboring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 107 records belong to 51 shots were analyzed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for these tunnel excavations and suggested for the test sites in order to estimate particle velocity of the ground vibrations. As a result of the studies, some practical charts are created in order to minimize the psychological effects of the shots, and simplify the authorities of shots’ job. And last but not least, make sure that the shots will be done in a controlled way.

Jan 1, 2011

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under development since. 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1998

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

By Steve Colbum

LTl’s MapStar LPS (laser positioning system) utilize both tripod mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environment characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, interactive software program, which can be run on any standard PC. Win Prof, the Windows-based analytical software package is used to reduce the data for generating bench face profiles, surfaces, volumes, estimating true burdens and mining ratio calculations. In addition, the software has many other built-in routines to calculate powder factors, toe shear, to map structural contacts and to predict the flyrock potential based on the Burden to Energy ratios. An extensive, built-in library of explosive’s data facilitates these calculations. It will also conform automatically to user-specified minimum and/or maximum burden in relation to the explosive energy, hole diameter and bench geometry - for both vertical and inclined holes. Numerical data can be represented in 2D or 3D to emphasize the hole-burden-face relationships.In this workshop, the MapStar LPS instruments and Win Prof analytical software will be thoroughly demonstrated. Demonstrations include equipment configuration, typical field setups and several effective survey procedures, including processing of some sample data.

Jan 1, 2000

By Scott Martin

This paper will discuss the challenges currently facing the mining industry. By sharing experiences gained in the CIM Leading in Mining Course, I will highlight what’s working, what’s not, what are the challenges, what are the concerns, what are the opportunities, what needs to happen. Specifically, I will discuss what is currently happening with leadership and leadership development in members’ own organizations, what skill sets are important to develop in different hierarchical groups and how comprehensive leadership courses like the leading in Mining course can help improve leadership within individuals and the industry. Leadership development is a process not an event.

Jan 1, 2014

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By Zajber A, Kulchen R, Letzel D, Weyer A, Schwellenbach J

The search for modem casting plant concepts today focuses more and more on the harmonisation and optimisation of overall concept lines to obtain a continuous quality control and reduce the cost of production (Figure 1). Fin I As far as continuous casting plant concepts are concerned, this specifically requires an optimal adaptation and flexible operation when converting liquid steel into a directly processable product without any in-between treatment. Continuous casters need to fully satisfy the requirements of both the upstream steelmaking facilities as well as the downstream rolling facilities.

Jan 1, 1999

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of arock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases(namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By I T. Tshabalala

In typical conventional narrow vein stoping operations, the use of temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The authors wishes to explore the probability and practicality of making use of new generation support products to make the support operations safer as well as enhance productivity in the stope face. This paper will examine the use of Autorock Drills as a means to drill roof support holes and install appropriate support components into these holes, as well as the application of ?Thin Spray Liners?, commonly called TSL?s as an additional means of creating a safer operating environment. The installation of netting as a means of roof protection and other support aspects such as cemented roof-bolts will also be explored. These proposed items are envisaged to improve the safety of our people and reduce production down time and increase production and productivity.

Jan 1, 2008

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By J. M. Avasthi

Gulf Research & Development Company conducted the nation's first underground coal gasification test in steeply dipping beds near Rawlins, Wyoming. The geotechnical considerations played a major role in the initial site selection. The test plan included a detailed geotechnical program for site evaluation, test design, permitting, and environmental studies before the burn. During burn, the geotechnical activity continued in the form of monitoring surface subsidence and acoustic emission. The postburn evaluation included studies of the drill cores obtained from the burn zone and effects on the surrounding rock mass.

Jan 1, 1981

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By B Beale

Bow-tie analysis is a commonly used tool to identify and display risks that have the potential for an undesired hazardous event. The output of the analysis are bow-tie diagrams, which are an effective and versatile communication format that can be applied to any type of risk. Contrary to their simplicity, a proper bow-tie diagram that maintains its usefulness and clear communication is difficult to build. Over two decades assisting Major Hazard Facilities with bow-tie analysis for Safety Cases, several common mistakes have been identified. This paper aims to highlight those issues with examples and provide improvement strategies. A sample of the most common mistakes are: - overly complicated risk analysis - poorly scoped and defined terms - poor descriptions and justifications - identifying too many dependent controls. Overly complicated risk analysis leads to wasted time in obtaining data for little gain. The bow-tie diagram is only a model. Effort should be redirected into identifying and managing controls that will make a tangible difference to site risk. Broad scopes lead to enormous and confusing bow-tie diagrams for both the user and the workshop team. Defining the scope of the study, the consequence severity of interest and critical control characteristics creates focused workshops and targeted analysis. With more definitive scope, there may be more bow-tie diagrams, however, they are succinct and specific. Well described causes are imperative for clear communication to users, regulators and future bowtie review workshop groups. It is best to use common wording structures and explain the event stepby- step. Also, clearly document any likelihood calculations and use data references where applicable. Identifying all possible controls creates a false sense of security that there are many layers of protection. In reality, most controls are dependent on a single system or person and could all be compromised from a single failure. A definition of a ‘bow-tie’ control is required whereby it must be independent from other controls. Improving the bow-tie analysis process will assist operators in developing meaningful and ‘operational’ bow-tie diagrams to support risk management systems and practices.

Apr 16, 2024

By Albert W. Deurbrouck

This report describes the preparation characteristics of the Pittsburgh and Upper Freeport coalbeds in Hancock , Brooke , Ohio , and Marshall Counties , W. Va . Over 4.5 million tons of coal was produced in these four counties in 1962. Most of this production came from the Pittsburgh coalbed . Twelve coal samples were collected for this study , 11 from the Pittsburgh bed and 1 from the Lower Freeport bed . Two of these samples could be upgraded to produce metallurgical - grade coal . The sulfur content of the Pittsburgh- bed coals was generally excessive --as high as 4.9 percent in the raw coal and 3.19 percent in the float 1.30 specific gravity fraction . The rank of the coals in this area ranges from high-volatile A to high-volatile B bituminous .

Jan 1, 1964