Search Documents

By G. A. Kordosky

Solution mining followed by solvent extraction-electrowinning (SX-EW) is one possible way to economically extract copper from ore bodies which cannot otherwise be profitably exploited. Published costs for the unit processes of SX and EW are out of date especially in view of the newer reagents now available and the newer circuit configurations, This paper updates the costs for SX-EW in 1985 dollars and also discusses some of the trade-offs which must be made when designing an SX-W plant.

Jan 1, 1986

By J. Yianatos, P. Vallejos

In the last decades, the exponential increase in the cells’ volume resulted in significant advantages such as investment costs, footprint and energy savings. However, in larger size cells, despite the increased diameter/height ratio, new constraints arose related to the need for decreasing the larger froth transport distances to enhance the froth recovery. Thus, the use of froth crowders and internal launders became compulsory to maintain the froth transport distances but decreasing the ratio between gas and collected mineral flowrates. Consequently, the bubble load will increase until reaching a critical bubble surface coverage. In this paper, the concentrate carrying capacity (tph/m2) is described in terms of the bubble surface coverage (bubble loading) at the pulp-froth interface and the froth recovery (froth transport) and is evaluated as a function of the cells’ volume and operating variables. A sensitivity analysis, based on industrial operating and design conditions, such as superficial gas rate, particles size, froth crosssectional area and cells’ volume, was developed for evaluating the metallurgical performance of cells from 100 to 630 m3. Results show that limiting carrying capacity can arise for the whole range of cells’ volume, depending on critical operating conditions, particularly in first rougher cells and cleaning stages of industrial flotation circuits. The increase in cells’ volume consistently increases the bubble loading (bubble surface coverage) under all conditions, approaching the limiting conditions more rapidly in the case of cells without internal launders. Otherwise, the limiting condition was achieved when the particle size DPS decreased from 50 to 20 (μm) and for superficial gas rates significantly less or larger than 1 (cm/s). The use of internal launders allows for increasing the range of the operating conditions needed to reach a certain carrying capacity. Keywords: Bubble carrying capacity, flotation cells, bubble surface coverage, cells’ volume

Jan 1, 2020

The price of copper has gone into the tank. So has gold. Environmental regulations are more restrictive. Global warming has world leaders and environmental groups seeking international regulations to keep the planet from heating up - mostly by restricting the use of fossil fuels. And the US Secretary of the Interior wants to make it more costly -prohibitively so for smaller companies - to mine hard rock metals in the United States. By rights, miners should be carrying around a pessimistic attitude about their industry. But miners are an optimistic lot, always believing that things will improve. That optimism was in evidence in Tucson, AZ in early December, when about 620 miners met at the Double- tree Hotel for the Annual Meeting of the Arizona Conference, put on by SME. Attendees listened as a United States congressman commented on the recent tax cut bill, mining regulations and the continuing need for the mining industry to improve its image in the eyes of the general public. Session speakers discussed how improved technology has made their processing operations at Sierrita and Morenci more efficient and cost-effective.

Jan 1, 1998

By P. W. A. Mayer

"As the push toward the northern regions of Canada steadily increases to exploit the rich mineral reserves, interest is steadily rising in respect to accessibility and climatic conditions and the problems posed thereby. In twelve years of operation, the Iron Ore Company of Canada, and associated companies, have found, through advanced technology, ingenuity and, most of all. need, some of the answers to the running of a profitable year-round open-pit mining operation."

Jan 1, 1966

By Cristhian Vía

El artículo detalla una experiencia de implementación de microequipos trackless para el minado de vetas angostas, orientada a mantener anchos de minado económicamente factibles, rentables y seguros y a reducir significativamente la sobredilución. Se explica el diseño geomecánico para dimensionar aberturas y paneles, y se describe la estrategia de minado en cada operación unitaria tanto como los parámetros de control. Como resultado, se reportaron mejoras en todo el proceso de minado y se redujeron a cero de los accidentes por caída de rocas. Se perfeccionaron los indicadores de seguridad de la unidad, se redujo la sobredilución de 30 a 10%, y el costo de minado disminuyó de 34.17 $/Ton a 20.63 $/Ton.

Dec 31, 2020

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By B. J. Morash

"The six mineable coal seams at Quintette Coal Limited (QCL) vary in thickness from 0.75 m to 9.5 m and include waste partings varying from 0.2 m to 4 m thick. They are highly faulted and folded in some areas and dip angles range from horizontal to 90 degrees. Due to this variation in thickness and orientation of the seams, several different mining methods are used to economically recover the coal. The key to QCL's success depends on the timely collection of detailed geology data and on mine planning which allows selection of the best method of mining to achieve maximum coal recovery with minimum dilution and cost. This paper will describe the various methods of mining employed and the criteria used to select them. IntroductionThe unique challenge in mining at Quintette Coal Limited (QCL) is to extract large quantities of coal and waste, from a complex orebody, with constricted areas for mining and waste disposal. This challenge dictates the mining of as many as four 10 m benches per year, through complicated coal structures, from three separate open pits with a total of 19coal seams. This total is made up of 5 seams at Mesa, 8 seams at Wolverine and 6 seams at Shikano (Fig. 1).Computer-aided mine planning and scheduling is carried out on a routine basis to ensure the prudent selection of methods of mining, to produce plans which ensure delivery of appropriately blended raw coals to the plant, and to coordinate disposal of large quantities of waste.Several methods of mining are applied simultaneously, and as a result coal and waste are released at different rates from twelve to fifteen mining faces. In order to ensure uninterrupted flow of material from excavators and to utilize the truck fleet effectively, a computerized dispatch system is employed.GeologyGenerally, geological conditions can be related to structural (faults and dip angle) and/or stratigraphic (coal seam and interseam waste thickness) sources"

Jan 1, 1988

Three computerised sets of minerals information are being developed by New Zealand Geological Survey in co-operation with the Resource Management and Mining group of the Ministry of Energy: 1. Geological Resource Map: a file of information on the location, geology, geochemistry, production, and potential use of individual occurrences of aggregate, mineral, geothermal, coal, oil, and gas resources. The computer program can be used for search and retrieval of information and the production of maps and tables. The data is being published as a series of 1:250 000 maps with accompanying text and tables. 2. Minerals Bibliography: an index and retrieval system for mineral exploration related; open-file company reports, N.Z. Geological Survey files, scientific research publications and university theses. 3. Minerals WhoÆs Who: an annotated directory of geologists involved in mineral exploration, mining and research.

Jan 1, 1986

Jan 1, 2000

By W. W. Adams

"The third annual safety contest for plants producing sand and gravel, which was conducted in 1911 by the United States Bureau of Mines in cooperation with the National Sand and Gravel Association, registered further progress in safety as compared with the two previous annual contests. Both the accident-frequency rate and the accident-severity rate were reduced.The period covered was the calendar year 1931; sixty plants participated, and 17 States were represented by the participating companies.The contest covered accidents and man-hours worked by all men at the participating plant who were employed by the same company; and it included work up to the point of delivery of the material directly to the consumer or to an independent agency of transportation--in other words, to the point of relinquishment of control of the material by the producer.The purpose of the yearly contests for producers of sand and gravel is to aid in the promotion of safety among the employees and in the reduction of accident costs to the companies. The contests develop friendly rivalry among the various plants and among the employees of individual plant in a concerted effort to prevent accidents.Two safety trophies are awarded annually, both of which are provided by Rock Products magazine. One of the trophies is for the host safety record among plants that were in operation the contest year 100,000 or more man-hours; the other trophy is for the best among plants that were in operation lees than 100,000 man-hours. Awards and the relative standing of the various plants are based upon statistical compilation by the Bureau of Mines of accident reports and employment reports furnished by the enrolled companies. are summarized at the close of each year, and the summaries are submitted to each company concerned for certification as to the accuracy of the summary and the completeness of the company's reports from which the summary was prepared. When the summery is returned signed by an official of the company, the records are considered to be a trustworthy basis for determining the relative standing of the various plants. The position of each plant is determined by its accident-severity rate; that is, the number of days of disability resulting from accidents for each 1,000 men-hours of work done by all employees at the plant."

Aug 1, 1932

By J. L. Lummus, Frank O. Jones

A field procedure for determining graphite in drilling mud is presented which is sensitive to 0.25 lbs/bbl and accurate to 20 per cent. The method, utilizing oil flotation principles, is suitable for use in all oil-free water base muds except those containing ligno-sulfonates, lignites, or surface active agents. INTRODUCTION Graphite was proposed as a drilling lubricant as early as 1940, but has not been used extensively until recently.' Graphite has been substituted for oil in certain instances to avoid oil contamination of core samples since it has been found that graphite does not interfere with routine core analysis. A major difficulty in using graphite is the lack of a satisfactory field test for determining the concentration of graphite in mud. DISCUSSION OF METHOD Several possible methods of analysis were investigated, including chemical separation, density fractionation, radioactive tracers, and oil flotation.', ' The investigation indicated that a satisfactory method for field use could be devised using an oil flotation method. It was found that toluene shaken with a highly diluted mud sample would recover sufficient graphite to be apparent in the oil phase. Refinement and standardization of technique made it possible to detect as little as 0.25 lb/bbl graphite and to estimate graphite content to within 20 per cent by using a visual comparison method. The test is limited to oil-free water base muds. Quebracho, phosphates, or barytes in the mud do not interfere with the test but surface active agents, lignosulfonates' and lignites evidently render !he graphite water-wet so that none may be recovered by oil-flotation. PROCEDURE Instructions for determining graphite in mud: 1. Collect representative one gallon sample.- from mud stream. Transfer immediately 350 ml portions of this Sample into four mixing cans labeled A, B, C, and D. Measure out graphite (same as is used to treat mud) for addition to cans as indicated below, using either a specially designed scoop or a balance. Can: A B C D Grams Graphite to Add: none 2 4 6 Stir samples B, C, and D for 15 minutes with propeller type mixer. 2. Clean and rinse well with water four 250 ml volumetric flasks labeled I, 11, 111, and IV. Using a 5 ml hypodermic syringe, transfer the indicated volume of samples from cans A, B, C, and D into designated flasks as follows: From Can: A B C D To Flask: I II III IV Add This Volume of Mud: 4 ml 2 ml 2 ml 2 ml 3. Measure 100 ml fresh or distilled water to each flask and swirl gently to disperse mud. Add exactly 5 ml toluene to each flask. Stopper and shake each

Jan 1, 1953

By Yagmur Sirinyurt, Ayhan Ali Sirkeci, Gülay Bulut, Mustafa Özer, Tuncer Acar

"The basic requirement of glass industry for the silica sand is at least 99% SiO2 content. On the other hand, coloring impurities such as Fe and Ti, must be removed. Flotation is the most widely used method for the purification of silica sands from impurities. In this study experimental studies were carried out to reduce Fe content of Mersin (Turkey) district silica sands by flotation. Silica sand sample with a d80 particle size of 1.85 mm was reduced below 0.5 mm in size. Then the size fraction -0.5 +0.106 mm was subjected to flotation tests. In flotation tests, sulfonate-type R801-R825, fatty acid based DER NA 7 (Produced by a Turkish company) and HA110-HA150 a blend of various chemicals produced by Mersin Cam-Is Mining Company (producer of glass raw materials) were used as collectors. Flotation tests showed that sulfonate type R801-R825 collectors provided much better results in acidic medium (pH: 3). The optimum pH value for DER NA, HA150 and HA110 collectors was found to be 7. It was observed that the addition of collector at once caused an increase in the amount of floated product that resulted in a loss of silica to the tailings. In the case of multistage addition of the collector much better selectivity was achieved. As a result of flotation tests conducted under best conditions, a concentrate assaying 0.046% Fe was obtained with a weight percentage of 93.4 when DER NA 7 was used as a collector. In the case of R801-R825 a concentrate was produced with 0.058% Fe content with a yield of 98.4%. On the use of HA150-HA110 the concentrate was produced with 96% weight recovery and 0.052% Fe content."

Jan 1, 2014

By Selim E. Woodworth

This paper, describing the milling practice on the Mother Lode as typified in the mill of the Argonaut Mining Co. at Jackson, Amador County, Calif., is one of a series prepared by the United States Bureau of Mines. The data herein presented and furnished through the courtesy of E. A. Stent, managing director and vice president of the Argonaut Co., covers operations from 1914 through the year 1929.

Jan 1, 1931

By Robert L. Lagace

The objective of this task was to perform theoretical analyses related to identifying and increasing the understanding of wireless propagation mechanisms in mines, and for predicting the performance ranges and limitations of proposed systems. This was to be achieved by building on and extending previous ADL work* and utilizing experimental data as they became available in the radio frequency bands of interest. B. TASKS Theoretical radio wave propagation investigations undertaken on this task centered on three areas. The first area dealt with extending previous UHF wireless propagation results*: to estimate the losses caused by the presence of haulage vehicles such as trains in coal mine tunnels; to estimate the propagation losses and wireless communication ranges expected along a longwall coal face tunnel; and to assess the applicability of previous analytical approximations to tunnels having reduced crossectional dimensions, such as those found in low coal and in the presence of haulage vehicles. The second area dealt with the development of a suitable propagation model to adequately explain the unexpected, highly favorable LF to MF band wireless radio wave propagation behavior experimentally observed in Consolidation Coal Co.'s Ireland mine. The third area dealt with the formulation of a model for evaluating the overall system transfer function and transmitter requirements for a hoist shaft LF communications system, taking into account the hoist rope/shaft transmission line characteristics, the cage and sheave wheel line terminations, the signal inductive couplers, and hoist shaft signal and noise data.

Jan 1, 1975

By S D. Dessureault

The largest surface coal mine in North America requires complex materials handling infrastructure to fulfil the highly variable quality specifications of its contracts. These diverse demands, reflected in the arrival of numerous customer trains every day, necessitate the integration of information in every stage of production. To meet this goal, quality measurement, train line-up and mine planning processes are being integrated into local and remote control rooms. The effectiveness of such a system can only be measured by comparing decisions that are made with, and without, each of the individual integrated control systems. Traditionally, mine controllers use their experience, intuition or a variety of trial-and-error spreadsheets to determine the ideal materials handling flows needed to achieve the correct quality. These balanced decisions are complex since many factors must be considered such as the mine plan, fleet costs, quality variability and others; consequently mine controllers usually have widely varying success between crews.An evaluation model was developed to assess the impact of a decision support system (DSS) integrated in a control room for controlling the coal blending process. To this end, an ARENA-based simulator representing the whole production process can be used to pull performance and current materials handling settings directly either from the real-time systems in the mine, or from historical data. In this way, the same shift (breakdowns, cycle rates, etc) can be simulated and performance compared. Different settings of the DSS, in terms of what information is displayed and the methods for doing so, can be tested for effectiveness. The historical data are extracted directly from a corporate data warehouse, without altering the everyday working databases. At the same time, the simulator writes its results back into the same data warehouse structure, allowing the same KPI reports to be used to measure simulated shifts.

Sep 26, 2011

By D. Harrington

Springing or chambering of deep drill holes is common practice in some quarries. It involves definite hazards from premature explosion during placing of the springing charges or the final charge due chiefly to heating of the bottom of the holes by the successive exploding of the springing charges or, in some instances, from burning of paper or other material following detonation of the explosives The danger is either unknown or disregarded in many instances by those who place the charges in the holes. Disregard of this hazard probably is, at least in part, responsible for the far too high fatality and injury rate due to charging explosives and premature slots in quarry work. Awareness of the danger' should result in elimination or at least of material decrease in injuries from this cause.

Jan 1, 1941

By Robert J. Evans

The monorail bridge conveyor (MBC) is a prototype continuous face haulage system that was surface tested and evaluated by the Bureau of Mines. The MBC consists of a series of cascading belt bridge conveyors suspended from roof-supported monorail track. Tests were conducted to determine MBC haulage capability, maneuverability, power consumption, and reliability using rigid and chain-suspended monorail track installations. Subsequent modifications to improve operation and reliability made during surface testing are described. Mining plans were devised to show potential MBC installations for room-and-pillar, longwall development, and shortwall mining sections. Compatibility tests were conducted with the Bureau's prototype hopper-feeder, to provide additional surge capacity and lump-breaking capability. Results from the surface test program, along with modifications to improve system operation and reliability, indicate that the MBC has the potential to perform success- fully in an in-mine trial.

Jan 1, 1987

By Thomas C. Denton

The Old Reliable copper mine was first examined by Harlow D. Phelps , an engineer of the Bureau of Mines , in October and November 1942 , in compliance with a request from the War Production Board , which furnished copies of assay maps of the 100- and 200-foot levels and requested that they be check-sampled . The author and R. li. Grantham and W. D. Hughes , engineers of the Bureau , made a second and more detailed examination later , after a number of manways had been opened that were inaccessible when the first examination was made .

Feb 1, 1947

By W. Ayvazoglou

A large number of organizations interested in the search for mineral deposits have adopted the magnetic method of geophysical prospecting, as it has proved to be the most simple, convenient, and rapid, and at the same time the least expensive in comparison with other methods. According to the last statistical data, about two millions square kilo¬ meters were explored in the United States by different geophysical methods. Ninety-six per cent of this area was prospected for oil and 4 per cent for minerals. Detailed exploration by means of the magnetometer has been carried out over about 85 per cent of this surface. The great advantages offered by this method resulted in the fact that the magnetometer was tried out in most places in which geophysical methods were applied. The main purpose of such e:rploration is to obtain the maximum knowledge valuable to the geologist; therefore good geological interpretation of the results of measurements is important. The possibility of drawing practical conclusions from a map representing the results of the study of the terrane depends greatly on the accuracy with which the measurements are made. The purpose of this article is to show the different sources of error by which the work of an operator may be affected and to discuss the means by which the carrying out of a magnetic survey may be improved.

Nov 1, 1931

By I. B. Lambert

The guide has been developed by officials from resources and environment agencies in the Australian Government and the South Australian and Northern Territory Governments. It elaborates on the Australian Government?s policy that new uranium mines are to be approved subject to world best practice environmental and safety standards. The guide outlines the best practice principles and approaches that apply generally to mining in Australia, before giving more detailed consideration to best practice environmental protection and regulation for ISR mining.

Aug 1, 2010