Search Documents

By Bailey, Lewis Newton

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on Apr. 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103d Engineers, killed in action near Fismes, Aug. 9, 1918. Bowles, Martin F., 2d Lieut., Co. B, 355th Infantry, killed in action, Sept. 3, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on Oct. 7, 1915. Dougall, Ralph, 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on Oct. 12, 1917.

Jan 3, 1919

By Leonard Obert

Part I of this report3/ proposed a sonic method for determining pressure, in situ, on rock pillar, arches, and other structures. The method required (1) a laboratory determination of the variation of the velocity of sound with pressure in samples of rock taken from mine pillars to establish a velocity pressure relationship for the type of rock, and (2) a measurement of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. The success of this method depends on the extent to which velocity of sound varies with pressure. Furthermore, Young's modulus of elasticity, E, can be calculated from longitudinal velocity, V, by the relationship, E = V2d ...(1) where d = density. Hence, the variation of the elastic modulus with pressure also can be determined. It pointed out that this method might be extended to assist in the prediction of rock bursts, inasmuch as the rock is subjected to extreme pressure in these instances.

Jan 1, 1940

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the US, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available.1 The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts. Definitions of some terms used in this presentation are necessary before proceeding.

Jan 1, 1980

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

The Cowarra gold mine is at latitude 36°O'S. and longitude 149°19'E. which is roughly 20 miles north-north-east of Cooma.The deposit was· originally worked towards the end of the last century, but the presence of sulphides associated with the gold in the primary zone caused cessation of work when that zone was reached.GEOLOGY AND MINERALIZATIONThe principal country rocks are sandstones and shales of Silurian and Ordovician age, both very strongly folded with structural pitches ranging from a few degrees to almost vertical. The mine proper is within Silurian rocks and the main orebody (there are several minor parallel bodies) is developed within a shear striking approximately north, dipping approximately 70° east, and ranging in width from 2 ft to 15 ft but averaging about 4 ft.This shear is impregnated with quartz and sulphides with which the gold is associated. The predominant sulphide is pyrite though pyrrhotite is commonly present in quantity.Arsenopyrite and bornite are present in smaller amounts.Stillwell (1936, 1937a, 1937b, 1938, 1941) has published five mineragraphic reports on the ore.The various levels have been mapped in detail (Figs. 1-3) and the No. 2 level plan (Fig. 1) shows the general relationship of shearing, as now indicated by mineralization, and faulting. There is no apparent connection between the fold structures and mineralization.Fig. 3 is a longitudinal projection showing the distribution of gold expressed as inch-ounces. The estimation of...

Jan 1, 1965

By Shosei Serata

The Stress Control Method improves productivity and safety in underground coal mining. The method stabilizes the roofs and floors of mine openings in both shallow and deep coal beds, regardless of whether or not there are ground stability problems. This paper describes the means by which a tapered pillar experiment is used to collect in situ data, which is then used as input for a computer model. The resulting computer model is then used to optimize Stress Control design for the mine under study. The behavior of any underground coal mine is not elastic, as is generally conceived in the conventional view of rock mechanics, but rather is highly time-dependent and site-specific. Unfortunately, conventional rock mechanics methods based on the elastic principle are not able to capture the highly non-elastic nature of ground behavior which actually occurs. To capture actual behavior, a new method of study is required. In this regard, geomechanical study of an underground coal mine may be compared to studying the behavior of a living fish. Its true behavior zannot be understood by examining it "dead in the laboratory. It Is the "live" nature of the coal mine that is required for design optimization of the Stress Control Method in the given mine. The Stress Control Method is based on a time-dependent theory of the global behavior of the mine ground, which generally contradicts the conventional elastic theory of ground behavior. Therefore, site-specific adaptation of the Stress Control Method required a comprehensive understanding of the global behavior of the mine as a function of time and site-specific ground conditions.

Jan 1, 1986

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By Charlie Jefferson

Main Goal: Resource Assessment 1. Incorporate existing data & results, old process. 2. NEW Quantitative Analysis (Chung and Chen) 3. Try mass balance of U and geochemical tracers 4. Use holistic process approach ?with key foci ?Targeted basin / belt assessments ?Is there as much in the Athabascaas they say? ?Athabasca reference for other basins (Thelon, etc) ?Compare sandstone & volcanic with USA, Kazakhstan etc: do their models apply here? ?Which IOCG systems are prospective for uranium? 5.Consider Groundwater, Environment; 6.Communicate

May 1, 2006

By Ernst P. Hall

The Irwin Basin. (Fig. 1)* is a synclinal or shoe-horn *Figure numbers throughout refer to color slides not included with the preprint shaped basin in the Pittsburgh Coal Seam, It is approximately 10 miles wide and 22 miles long at its maximum points. The surface of the land above the basin is hilly, rolling farmland,, typical of this area of Pennsylvania, and it is criss-crossed with streams and highways and liberally dotted with farm houses and communities. In-general the coal is pitched from north to south with a total drop of 610 feet'. The coal seam cross-section from east to west is bowl-shaped and rises as much as 375 feet from the low point of the bowl to-the-outcrop. Cross-sections showing coal elevations are shown on Figs, 4 and 50 Ground cover above the coal will vary from 0 to 550 feet, averaging about 350 feet throughout the area. This area is richly endowed with a history of coal mining. The first car of coal shipped cast of the Allegheny Mountains was mined in the Westmoreland Coal Company's Shady Grove (later North Side) Colliery in Irwin, Pa., early in 1853, This mine was opened in 1852 by Coleman, Hillman & Company. The coal was hauled from the mine to the freight station by horse-drawn wagon and. loaded into a then "standard" box car of 18,000-pound capacity. Coal mining in this region flourished and grew as steel production in nearby Pittsburgh demanded more and more of the high quality, metallurgical-grade coal of the region.

Jan 1, 1959

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

By Y. C. Kim

For the past few years, the Cyprus Bagdad Copper Company began experiencing a significant "ore-dilution" problem from its low grade open- pit copper mine located at Bagdad, Arizona. To pinpoint the causes of this dilution, a study was initiated to investigate as well as to improve in-pit ore-waste selection-procedures using conditionally simulated ore-bodies. Prior to the actual use of conditional simulation; a comparison of different estimation methods for a mined-out area in the pit was performed. Specifically, kriging estimates were compared against the original estimates of the company which were based on the polygonal approach. The results of this comparison clearly identified part of the so- called "ore-dilution" problem, which was the initial over-estimation of average ore grades from blast rounds, using the polygonal approach. The results from the use of conditionally simulated orebodies demonstrated that the "ore-dilution" problem can be reduced by more than half if in-pit ore- waste selection is based on the kriged estimates rather than the polygonal estimates. This simulation study also showed that the current use of the polygonal approach has the effect of shipping a larger tonnage of lower grade material to the mill.

Jan 1, 1982

By João M. S. Rodrigues

The use of sandblasting as a treatment method for conditioning anodes for zinc electro-winning was investigated and compared with conventional fluoride preconditioning. The anodes were made from two different lead-based alloys (Pb-Ag-Ca and Pb-Ag). Laboratory results showed that sandblasting and preconditioning both minimize lead contamination in the zinc and sludge generation. Sandblasting was found to have no aggravating effect on the anode corrosion. The sandblasting treatment was tested on Pb- Ag-Ca anodes on an industrial scale in the celJhouse of a local zinc producer. An unexpected finding of the large-scale tests was that the sandblasting appeared to strengthen the anodes, resulting in reduced warping during handling and operation.

Jan 1, 1996

By D. C. McLean, S. A. McKay

The purpose of this paper is threefold: 1) to describe actual ground control installations made at the various mines of the International Nickel Co. (Canada) Ltd mines in Sudbury, Ont. during a planned test program. 2) to suggest new ground control techniques which are now possible by the use of fully grouted bolts 3) to indicate the possible economic advantages to be gained by the use of resins and resin grouted bolts to control difficult ground conditions. Were a theme selected for this paper it would be: "Preserve the original roof in best condition possible by the use of smooth blasting techniques and fully grouted roof bolts — since the original rock is the best and cheapest material available for ground support." TYPES OF BONDED BOLTS As has been shown previously, there are several ways in which a bolt may be bonded. These are illustrated in Fig. 1 and 2. There are three general types of grouted bolts: 1) pretensioned, 2) post-tensioned, and 3) untensioned. The type which will be of most benefit to the user will depend upon the particular ground support problem involved. Despite the many arguments propounded for the necessity for using a tensioned bolt, ample evidence exists from actual experience that untensioned bolts can be effective in many instances. The outstanding characteristic of a grouted bolt is that it provides the user with a variety of rock consolidation techniques heretofore unavailable with conventional rock bolts. Many of the unusual characteristics of grouted reinforcing bar have been evaluated by researchers in the concrete structure field.' Underground application has largely been pioneered in the construction field, with especially good work being reported from the Snowy Mountains Hydroelectric Authority in Australia. Techniques developed there using cement grouted bolts are now being adapted in many large government construction projects in this country with excellent results. The ap- plications described in this paper are those in which Cyanamid's Roc Loc Mining Kits were used exclusively. SLUSHER DRIFTS AND FINGER RAISES (BOX HOLE BROWS, DASHES) A common mining problem especially where block caving methods are applied is that of maintaining the roof in slusher trenches particularly at the intersections of the trench with the feed raises (box holes) through which the large fragments of broken ore tumble. Typical sections are shown in Fig. 3 and 4. In Fig. 3, the drift is normally driven 7 ft wide by 8 ft high initially. The rock involved is a hard norite (diabase) which is usually competent but has "block cleavage". This roof has a tendency to fall out in large blocks when subjected to operating stresses. Depending upon the initial condition of the roof, the drift is either lined with 2 to 3 ft of concrete immedi-

Jan 1, 1964

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By Shepherd J

Megascopic and microscopic studies of cleats and mining induced cleavage in Ihe first workings at Leichhardt Colliery reveal the presence of four distinct fracture sets. Microscopic studies confirm underground observations of the fracture sets.The most likely order of formation of the fractures is (i) "butt" cleats (ii) facc cleats (iii) shallow dipping faults (iv) mining induced cleavage. Three fracture sets apparently formed by tensiIe failure. Microscopy shows that the mining induced cleavage surfaces have preferred starting or lerminating points at the extremity of a "butt" cleat and a vitrite-dull coal band boundary. It is postulated that the induced cleavage begins at 'butt' cleats which behave as Griffith flaws under high compression around Leichhardt Colliery faces. Instantaneous outbursts of coal and gas are associated with only those workings which are affected by mining induced cleavage and occur at or adjacent to working faces.

Jan 1, 1981

By P. W. van Deventer

?Soil quality is the capacity of a soil to function, within ecosystem and land use boundaries, to sustain biological productivity, maintain environmental quality, and promote plant, animal and human health?. In the long-term, vegetative rehabilitation of mining wastes aims at, as far as possible, the proper ecological integration of the reclaimed area into the surrounding landscape, which is sustainable and requires minimal maintenance. A certain succession pattern is therefore needed. Recent ecological concepts recognize the role of the substrate?s quality and nutrients in affecting the rates and directions of succession patterns. Although pedogenesis and eventually soil quality in mine waste are not well known, monitoring of soil quality parameters in kimberlite mine tailings reveal a remarkable establishment and or improvement of specifics oil quality indicators. During the same time the vegetative cover?s total functionality as well as reproductive ability improved. Functions of soil, and thus soil quality, can be assessed at the field, farm, ecosystem, pedosphere, and global scale. It is recognized, however, that management of soil becomes increasingly difficult at larger scales, but for demarcated mine waste sites it is possible to ameliorate and manage and assess soil functions and quality. Therefore the significance of the study is the following: soil functions and quality become inseparable from the idea of system sustainability, and are considered as key indicators of ecosystem sustainability on rehabilitated mine tailings material.

Jan 1, 2008

By Jeffrey C. Hillman

The need to recruit locally produced engineers by the South African Mining Industry led to the Engineering Faculty at the University of the Witwatersrand developing a number of academic bridging initiatives for educationally disadvantaged students. The graduation rate achieved during the initial five years of operation by the most successful of these programmes has been on a par with that of al other students but the performance of subsequent intakes has declined to such an extent that the continuance of this scheme could now be at risk. One reason for this reduction in throughput is that many of the applicants for the increasing number of mining bursaries have been more interested in the bursary than the profession and have either failed or dropped out due to a lack of application and motivation. This will have serious consequences for both Wits and the Industry if it continues and some method of identifying unsuitable or suspect applicants needs to be introduced as a mater of urgency. It is recommended that an introductory course be set up at a working mine that would be run under the auspices of Wits, as a joint venture with industry, and include a level of academic input that would provide both bridging needs and certain first year credits. The final form of this course will require extensive consultation with al parties but needs to be completed before the end of 1996. It is further recommended that the advertising and promotion of mining careers be expanded and much improved.

Jan 1, 1996

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

USBM Contract H0133045 consists of the design, build and test of 50 waveform generators. The waveform generator is a small ULF transmitter operating in the 1 to 3 KHz frequency range for the purpose of locating trapped miners during a mine disaster. This contract provided for the design, test, and building of 50 waveform generators using a discrete component construction with an option of using hybrid construction techniques within 105 days after the effective date of the contract. Because of large quantity economic considerations, this option was not initiated. Two engineering models were designed, constructed and tested and 50 final production units were fabricated using discrete construction. Complete documentation is supplied under a separate package which includes final schematics, parts list, layout information, equipment specification, production test procedures and qualification test procedures. Ten units have been delivered to the USBM. The remaining 40 units are being retained for packaging under contract H0242010 Transmitter Package and Receivers.

Jan 1, 1974