Search Documents

Breakwater Resources Ltd is a Canadian base metals producer with Cu-Pb-Zn operations in Canada, Honduras, and Chile. Two of its operations contain economical gold levels which are recovered in both gravity and flotation concentrates. The gold payable terms in zinc concentrate are poor when compared to gold concentrates or copper concentrates and various flow sheets have been evaluated by Breakwater staff to maximise gold reporting in higher value products. The Myra Falls mine in British Columbia recovers coarse gold in the grinding circuit, part of which is upgraded and sold as a gravity-gold concentrate with the balance being directed to the copper concentrate. A sampling survey showed that there was potential gravity-recoverable gold in the copper regrind circuit. Installing a gravity concentrator in the copper regrind circuit increased the gold grade and recovery in the higher revenue copper concentrate and reduced the quantity reporting to the less well paid zinc concentrate. The El Toqui Mine in southern Chile has distinct high-and low-gold orebodies which are campaigned separately through the flotation plant. The high gold zone yields both a gravity concentrate and an unusual gold flotation concentrate. The gravity concentrate undergoes intensive cyanidation and electrowinning on-site to produce dore, while the fl otation concentrate is sold to gold producers. The zinc concentrate contains signifi cant gold values. The paper describes efforts over the past few years to improve gold returns at Breakwater's operations and highlights the different approaches dictated by the mineralogy of the gold occurrences at these two operations.

Aug 1, 2010

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

By J. S. Stachulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The first objective is to prevent a fife.The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife.The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife. Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By J. S. Stacbulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The flirt objective is to prevent a fife. The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife. The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife.Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

This method determines tellurium at concentrations down to 0·01 p.p.m., with geochemical accuracy. Tellurium is volatilized from the rock at 800°C in the presence of sulphur from decomposing pyrite, condensed, dissolved, and finally determined by atomic absorption in a long tube burner. The distribution of Te is shown near some gold lodes at Kalgoorlie. Lastly, a method of synthesizing Te-free pyrite from sulphur and ferrous sulphate is described.

Jan 1, 1969

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By D. Vogt, T. Hattingh

"This paper argues that the technology change to mechanization is also going to require a change in people. It presents a model for technological progress and adapts it to the mining industry. It then goes on to motivate the need for mines to become learning organizations in order to achieve maximum value from their people as they become less labour-intensive. In an important sense, mechanization is as much about knowledge as it is about technology.The change when a mine introduces mechanization or a level of automation is not simply one of technology but also a stage in the development of mining from ‘art’ to ‘science’. ‘Art’ describes a state of technology characterized by tacit knowledge, an understanding that comes only from experience, and has no formal procedures and little structure. In contrast, ‘science’ represents a state of technology where all the component processes are understood in detail, all knowledge is explicit, and processes and structures are formal.Studies of other industries, including metal part manufacture and aviation, show that each stage in the progression from art to science changes the nature of the organization and requires a different mix of skills from the workforce. Perhaps the most important change is the increase in knowledge and decision-making required as the technology gets closer to science.There is anecdotal evidence that South African underground hard-rock mines are not learning organizations. Mines by their nature are capitalintensive with long lead times from investment to returns, so there is reluctance to change from the original plans or to encourage staff to think independently. Particularly as mines move from art to science, this reluctance must be overcome.The important lesson for engineers involved in introducing mechanization is to understand that success or failure will be determined by the people involved, and not solely by the technology. The process will almost certainly require a culture change on the mine. We recommend that the mechanization team includes an expert in human and organizational behaviour to ensure that a receptive workforce and management are in place to accept the new technology when it arrives."

Jan 1, 2016

By A. U. Miller

Definite progress has been made in accident prevention in Illinois during the past few years; the State Department of Mines and Minerals is receiving excellent cooperation from coal companies and employees, the companies are making greater effort to maintain their mines in good condi- tion, and the employees are eliminating more unsafe practices. As a result, some coal companies have made commendable safety records that prove that coal can be mined with a comparatively low accident rate. However, there is need for further improvement, as the accident rate of the State as a whole is much higher than it should be. During the 55-year period 1882-1936, in- clusive, reports of the State Department of Mines and Minerals show a total of 7,005 (an average of 127.36 per year) men killed in and around the coal mines. Of this number, 6,425 (91.7 percent) were killed underground, 346 (4.9 percent) in the shaft, and 234 (3.3 percent) on the surface. Of the fatalities underground, 3,300 (51.3 percent) were killed by falls of roof, sides, or face coal, 1,167 (18.1 percent) by haulage, 639 (9.9 percent) by handling explosives, 579 (9 percent) by explosions, 151 (2.3 percent) by electricity, and 589 (9.1 percent) by other means. Of the fatalities in the shaft, 171 men (46.5 percent) were killed by falling down the shaft, 14 (41.6 percent) by the cage, and 31 (8.9 percent) otherwise. On the surface, 113 (48.2 percent) of the fatalities were due to railroad cars, 51 (21.7 percent) to machinery, and 70 (29.9 percent) to other causes. The fact that 7,005 lives (an average of 127.36 per year) were lost during 1882-1936 is sufficient evidence that in the past too little interest has been taken in safety by either the management or workers. A realization of this deplorable loss of life should act as an incentive to the industry to make greater effort to prevent accidents in the future. After an accident occurs, the facts pertaining to it become history, and anything that may be done afterward cannot change in any way the damage that has already been done, such as loss of life, personal injury, and destruction of property. The main benefit that can be derived from an acci- dent is that suitable procedure may be adopted and some lesson may be learned to aid in preventing a similar accident in the future. All accidents, par- ticularly serious ones, therefore should be investigated and an effort made

Apr 1, 1938

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By D. Hoffmann, S. Plumb

IRUP is an iron-rich ultramafic pegmatite rock that formed due to hot ironrich fluids and gases replacing local stratigraphic zones of the Bushveld Complex. This study focuses on the estimation of the probability of IRUP occurrence on the Merensky Reef at the Marikana Karee Mine. A 2.15 million centare IRUP-rich domain at the Karee Mine was initially defined from the interpretation of a surface aeromagnetic anomaly, and exposures in the mine workings. Surface boreholes (spaced 250-500 m apart) within this IRUP domain contain approximately equal numbers of IRUP-replaced and IRUP-free intersections. Owing to the uncertainty in the continuity of the IRUP alteration (a result of the wide borehole spacing), the risk associated with the development of mining infrastructure within this domain is unquantifiable. Semi-quantitative data comprising visual estimates of IRUP replacement from reef development mapping data and surface borehole reef intersections was interpolated into blocks using indicator kriging estimation. Comparative analyses of the estimate of IRUP occurrences were made by changing the block size and declustering the data systematically. Reconciliations of the probability of IRUP predicted from the block models derived from the different data-sets and sequential indicator simulation models were analysed for four mining study blocks. A quantitative approach to modelling the occurrence of IRUP can be an additional tool for refining the estimate of the geological losses that inform the mine plan in such high-risk zones.

Jan 1, 2015

By Guillermo Silva, P. Katsabanis

The conventional approach to design wall control blasts relies on the borehole pressure as the most important explosive parameter. Borehole pressure is intimately linked to explosion pressure, which in turn is related to the detonation pressure of the explosive. For fully coupled charges, the borehole pressure is equated to the explosion pressure, while for decoupled and decked charges its value is typically calculated under the assumption that the explosion products behave like an ideal gas when they expand into the volume of the hole.

Jan 1, 2003

By M S. Tuohy

Since the independent review of fatal accidents in the mining industry carried out by Dr Sean Brady (the ‘Brady Review’), High Reliability Organisations (HROs) and their operating principles have been discussed across the Queensland mining sector. HROs are organisations said to consistently avoid serious failures, reliably delivering their organisational objectives despite operating in environments characterised by high levels of inherent risk and/or operational complexity. HRO concepts have previously found application in other similarly hazardous industries to mining. However, as Hopkins (2009) pointed out, HROs ‘are very elusive creatures that inhabit the realm of theory more than the real world’. The Queensland Resources Council (QRC) with support from the Commissioner for Resources Safety and Health initiated a review of how HRO principles can be translated to the mining industry. The review was conducted by Noetic, an Australian management consulting company that specialises in hazardous industries, including mining and metals, and has prior experience applying HRO theory.

May 5, 2022

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit, in Yemen, contains at least 9.4 Mt at a grade of 10.7% zinc, 2.2% lead and 77g/t silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to conventional smelter/refineries, and it has been necessary to formulate a less conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material, at Yanbu, in Saudi Arabia. In order to give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulphide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, the flowsheet for Yanbu and presents preliminary costs for both operations

Jan 1, 2002

By Andrew Bamber

The introduction of pre-concentration technology into the underground narrow-vein mining scenario has the potential to change the entire economics of utilizing bulk-mining methods in these situations. An idealized integrated underground mining and processing system, comprising elements of bulk mining, underground preconcentration and backfill systems is presented. Through simulation and a systems engineering approach, the implications of enabling the utilization of bulk mining methods in a narrow vein deposit through the adoption of this technology is considered. Parameters considered include orebody characteristics, ore mineralogy, grade, metal value, mining rate and cost.

Oct 1, 2004

By W. W. Adams

The quantity of explosives sold in the United States in January, 1931, for domestic consumption, amounted to 368,100 kegs (9,202,500 pounds) of black blasting powder, 4,610;000 pounds of permissible explosives, and 16,533,000 pounds of high explosives 'other than permissible. These figures are based on reports received by the United States Bureau of Mines, Department of Commerce, from nearly all manufacturing companies, and include an estimate of sales by several companies that do not furnish monthly reports. Reports actually received from manufacturers showed soles of 365,977 kegs of black blasting powder (consisting of 220,892 kegs of granular powder and 145,085 kegs of pellet powder), 4,687,900 pounds of permissible explosives, and 15,496,152 pounds of high explosives other than permissible. Sales in January, 1931, were smaller than in January, last year, the decreases being 14 per cent for black blasting powder, 19 per cent for permissibles, and 17 percent for high explosives other than permissible. Sales in January 1931 when compared with soles in December 1930, show increases for all three classes of explosives as follows: 2 per cent for black blasting powder, 16 per cent for permissible explosives, and 7 per cent for other high explosives.

Jan 1, 1931

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By J. B. Zadra

The use of activated carbon for extracting gold and silver from pregnant cyanide solution and pulp has been investigated many times. The primary advantage of this use of activated carbon is that .the dissolved values can be recovered from slimy ore pulps or from slime portions of ore without settling and thickening or filtering. The loaded carbon is removed from the barren pulp, and the pulp can then be discarded. Activated carbon has been used recently in treating gold ores containing very little soluble silver. When the carbon was loaded with a suitable amount of gold, the silver load was negligible. The remaining problems concerned the removal of the gold from the carbon, the recovery of the gold as bullion, and the reuse of the unloaded carbon. As described in a recent report, a method that solved these problems was developed. The gold-laden carbon was leached with caustic sodium sulfide solution and the gold simultaneously recovered by electrolysis. Both the carbon and the spent solution can be reused. That process was applicable to gold-laden carbon only. It was not applicable to carbon carrying silver, because sodium sulfide does not leach silver from carbon but "fixes" it. It has been necessary, therefore, to develop a modified process for the removal or desorption of both gold and silver from loaded carbon. This modi¬fied process permits the use of activated carbon for extracting both gold and silver from gold ores carrying enough silver to have economical interest or in which silver may be the predominating value.

Jan 1, 1952

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009