Search Documents

By D. Harrington

Correct ventilation of underground workings whether in coal or in metal mines consists in establishing such control of air currents that the miners may work in safety, with maximum comfort and efficiency, and without impairment of health; also in controlling the air flow so that the mine workings may at ordinary times be kept reasonably free of harmful gases or dusts, and so that in time of emergency, as when a fire or an explosion occurs, there may with minimum delay be maintained as much or as little air flow as is desired throughout the mine in its entirety or in certain parts of the mine. Control of air flow is the essential point of any mine ventilating system, and is obtained only by the installation of mechanically operated fans, and other ventilating devices such as doors; overcasts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. Much has been written about natural ventilation, and many claims have been made that in specific mines or parts of mines there is sufficient natural air flow. As a matter of fact, there are actually very few if any mines, coal or metal, where natural ventilation creates atmospheres anything like adequately safe or healthful for underground workers even at ordinary times or under ordinary. conditions; and at the time of a fire or an explosion mines depending upon natural ventilation are practically helpless, and are decidedly dangerous for the unfortunates forced to be in them either at the time of the disaster or afterwards when trying to handle conditions arising from the emergency.

Jan 1, 1929

The status quo of ecological rehabilitation in metal mine in China and progress in the technology for ecological rehabilitation are presented, including soil reconstruction, soil improvement, plant selection. The present and future research fields are suggested: basic theory of ecological rehabilitation, operative technology of ecological rehabilitation, new technology application research and ecological rehabilitation plan, management and policy.

Jan 1, 2014

By RAY LYMAN WILBUR

SINCE boyhood I have had a keen interest in mining engineering. To see the prospector with his pack outfit and his pan, followed by the assayer and the trained engineer, has always had -something of the lure of romance for me. It is appropriate that the American Institute of Mining and Metallurgical Engineers should hold a general meeting in California, since this State has long been a home of mining engineering. Here, after the early open methods of mining, it has been necessary for the universities to train men in geology and mining, so that the earth could be penetrated and the rich ledges opened. In the eighty years in which the mines of California have been offering experience to the miners of the world, we have seen mining engineering evolve from a comparatively simple art, covered largely by rule of thumb, into a complex group of specialties, each utilizing the very latest discoveries in the various fields of physical sciences. Mining, too, has become a great business requiring large financial support and the most careful handling. Those mining engineers who have applied new processes in special fields have thus been able to give a wide-flung range to their activities in all parts of the world. The hand of nature in distributing minerals over the surface of the earth has compelled the mining engineer to become a modern pioneer, facing the heat of the tropics as well as the frozen regions of the north. There has been a marked cosmopolitan aspect to mining engineering, since the engineer had to go wherever the prospector discovered favorable leads. This has meant dealing with the harshest of conditions, the handling of labor of all sorts, the control of sanitary conditions, and relations to all forms of transportation. Naturally this has called on some of the very best minds in all countries to unlock the stores of hidden wealth. To make them available for civilization has been the job of the mining engineer.

Jan 1, 1929

By J. G. MacGregor

At this, the opening meeting of the Western Quebec Branch of the Institute, it seems fitting that the first paper presented should embrace a survey of the known mineral deposits occurring in the area, and also a review of ?the exploration methods that have brought about their discovery. And since the study of geological structures must always be the guiding principle of an intelligent exploration campaign, it also seems to be the appropriate occasion to review the geological situation from the economic angle, in an attempt to arrive at a re-statement of the known facts governing the deposition of the mineral bodies . . It is not my intention to confine my remarks entirely to the geological problems involved, but rather to pass under review the exploratory methods that have been employed in the past and that are presently being used, and to offer a forecast of the type of exploration campaign that will be largely adopted in the future search for ore.

Jan 1, 1929

By A. W. Fahrenwald

Flotation practice in Idaho is now about 13 years old. The advance has been steady during these 113 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. Ores of the District The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and' 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By S. Gan, E. van Niekerk, L. Birrell, D. Robbertze, L. Ncubi, B. Zhao

Quality assurance and quality control (or QAQC) plays a key role in safeguarding the level of confidence of the data generated during mineral exploration and mine development, and is also part of the reporting code requirements for resource estimation and reporting, as well as mining investment. Implementation of good policies and working protocols in quality management will result in the generation of reliable information, which is critical for decision-making on the future of the mining project. The use of certified reference materials, i.e., standard, blank, and duplicate samples, proves effective and efficient for ensuring the level of data confidence in terms of precision, accuracy, and sample contamination. This is well demonstrated by the practice of QC in the exploration programme for the chrysotile tailings storage facilities of Havelock Mine, using 1254 samples from 53 drill-holes. Different statistical tools were applied to analyse the assay results from these samples. The outcome substantiates that the QC practice established during the Havelock exploration project is aligned to best practice guidelines in the industry. The resource delineated indicates that the tailings material at Havelock could potentially become a significant source of supply to the global magnesium market.

Jul 2, 2022

By G. C. RIDDELL

THE metallurgist, chemist, and physicist are blazing trails that lead far afield. Pushing on into an "Alloy Age" they see a non-ferrous era over- taking iron and steel. Delving into the nature of the physical world, they break down a supposedly indivisible element, hydrogen. Not content with terrestrial problems, they peer back along the cosmic ray into iaterstellar space, glimpsing forces that are, apparently, still busy with the task of atom-making. Mastering and organizing the material and physical, they advance steadily toward that borderland of science where the concept of matter itself seems abandoned, and force is the substance left.

Jan 1, 1930

By Barry James

Energy, like labour and materials, is one of the basic production inputs in the industrial minerals industry. This paper discusses the significance of the changing energy situation in Canada as it affects the industry. It is apparent that the importance of energy as a management concern has increased considerably since 1973. The importance placed on energy management today will undoubtedly be an important factor in determining company and industry sector strength and profitability tomorrow.

Jan 1, 1978

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

Two outstanding features of the world's young orogenic belts are their very consistently developed suites of volcanic rocks and, it is now recognized, the rather distinctive types of mineralization they contain. Further,it is now known that these volcanic suites exhibit evolutionary patterns, and it is beginning to appear that this evolution in style of igneous activity is accompanied by a parallel evolution in style of mineralization. Specifically,podiform chromite and stratiform pyritic copper ores of Alpine ultramafic/submarine tholeiite association progressively give way to more zincian stratiform ores associated with andesites and dacites, "porphyry copper"deposits developed in quartz dioritic to dacitic plugs, and lead-zinc stratiform ores related to increasingly pyroclastic, rbyodacitic volcanism.This "coupling" is exhibited well in the volcanic arcs - the young orogenic zones-of the SW Pacific which, with tbeir abundance of youthful and commonly unmetamorphosed materials provide an opportunity for investigating, through a petrochemical approach, the possible significance of ores in the elucidation of mechanisms of lava formation. It is suggested as a working hypothesis that in the orogenic (voleanic arc) regime ores are associated with the cale-alkaline rocks because these cale-alkaline rocks are in part generated by exhalative loss, and the ores are among the manifestations of tbat loss.

Jan 1, 1978

By R. R. Sayers

The hazards connected with work under abnormal air conditions are becoming of increasing importance from a financial as well as a physiological stand- point, due to the extension of compensation laws to include diseases caused by dusts, toxic gases, and abnormal temperatures and humidities. The United States, with the excention of California, North Dakota, Wiscon- sin, Massachusetts, and Connecticut, is the only English-speaking country to-day where silicosis is not compensated.3 Cases of permenent total disability or death due to silicosis mar aprear in common-law courts, particularly in the States that have not recognized silicosis as an occupational disease for which compensation should be provided. Such cases have recently been tried in one State, according to a magazine editorial, not providing scheduled commensation for employees affected by silicosis, with results favorable to the claimant. Clearly established cases definitely linked with occupation as the cause may be expected to be recognized as deserving by juries and courts, and awards will be made. In one Atlantic Coast State, according to this editorial, 108 claims for silicosis, including 21 deaths therefrom, are said to have been filed against two small plants engaged in finely pulverizing quartz sand.

Sep 1, 1932

By C. Michael Morgano

Static tests are costly and time consuming, so they are not always the best answer [ ]

Jan 1, 2005

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By Harold J. Rose

The economic situation in Switzerland during recent years has resulted in theoretical studies , engineering development work , and many commercial installations of ingenious methods for using energy more efficiently . The purpose of the present investigation was to learn of recent Swiss developments for the more effective use of coal , which comprises 98.9 percent of the romaining known mineral - fuel reserves of the United States .

Jun 1, 1947

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf' commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

By L. Telfer

Summary During Palaeozoic time, there were deposited in the Canadian Rockies four beds of phosphate rock, ranging in age from Mississippian to Jurassic. Two of these beds are of probable economic importance if some means of separating the phosphate from the gangue can be devised. All the more important beds of phosphate rock so far discovered are just behind the front ranges of the Rocky mountains, within fifty miles of the prairie lands of Alberta. Mining conditions are favourable, with an abundance of timber and ample power available. The phosphate beds are all of the sedimentary type, and they all occur, apparently, at the same stratigraphic horizons over a wide area. The conditions necessary for deposition evidently occurred at several different periods in geological time, and were widespread. The most important factor appears to have been the condition of the land surface surrounding the basin of de-position. Both oolitic and nodular phosphate were laid down under nearly similar conditions. Introduction Following the discovery of phosphate rock in Idaho and Montana, search was commenced in Canada to determine whether formations of similar age in the Canadian Rockies carried similar beds of phosphate. The most widespread search has been that undertaken by the mines department of the Consolidated Mining and Smelting Company of Canada. The following paper will discuss some of the results of this exploration.

Jan 1, 1933

Discussion of the paper of IRVING A. PALMER, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1447 to 1460. L. S. AUSTIN, Salt Lake City, Utah.-With the union of the Guggenheim interests and the American Smelting& Refining Co. in 1900, competition among the lead-smelting companies appeared to have been largely eliminated. This condition prevailed for but a short time, owing to the erection of smelteries by competing companies. Naturally, as competitors, the older companies endeavored to keep improved methods to themselves, not realizing, it would appear, that such knowledge could never be bottled up, but would drift into the common field of practice. Of late it has begun to be felt that more is gained than lost by adopting a franker and more open policy. The line, however, is drawn in. giving details of costs, which, fully known, it is felt, would be taken advantage of by a rival. As Mr. Palmer says, steady and substantial progress has been made, and latterly, I may add, the improvements have been radical. Sintering by the Huntington-Heberlein method or with Dwight-Lloyd machines has effected an important saving over reverberatory roasting, the cost being, say, 50 to 75c., as compared With $2 per ton by the older method. Moreover, the .large use of a sintered product has resulted in doubling blast-furnace tonnage. However, the change has not been an unmixed blessing, as in the machine roasting little time can be given to the breaking up of the blende, and it has been impossible to decompose largely the zinc sulphide, so detrimental in later blast-furnace treatment. The satisfactory roasting of the blende is still an unsolved problem. Nor is this all. For the best reduction it has been found that a part of-the change should be crude (unsintered) ore, indicating that the already fused material is only too ready to change to slag, thus lessening the opportunity for better reduction.

Jan 11, 1914

By Hitendrabhai S. Dewangan, Dr. Aashish A. Mehta

Pile foundation is widely used in construction of marine structures. In offshore & marine piling work, drilling/boring supporting fluid is used to stabilize the borehole (excavation) prior to tremie concrete. The poly-fluid is a synthetic drilling granular polymer characterized by high molecular weight.it is mainly used for the preparation of stabilizing and lubrication mud in drilling of deep foundations. Disposal of polymers after using it into the sea, pollutant the sea environment, which may be harmful for living organisms inside sea. To reduce the pollution in offshore/Onshore, it is essential to take the precautions during flushing operation with proper recycled, reused & it’s Disposal. To provide economic and environmental solutions, used slurry was treated with addition dose of fresh material/polymers. The amount of fresh materials/ Polymer to be added can be decided based on (viscosity, density and pH value) test results. Finally, initiate water flow and air agitation as required. Run the tests on the re generated slurry before transferring to storage tank. Also, after storage, polymers will be reused for next operation. Moreover, mud wastage coming from borehole will also be disposed at suitable dumping places.

Sep 1, 2022