Search Documents

By Clarence A. Johnson

The discovery of the Prudhoe Bay field temporarily reduced interest in the development of coal conversion processes, but interest is being re¬newed by the current energy crisis. According to M.A. Wright, Chairman of the Board of Humble Oil and Refining Company(l), the reserve in the Prudhoe Bay bield has been confirmed to be about 10 billion barrels. At first glance this appears to be an extremely large reserve which will eliminate supply problems for the United States for some time. This feeling of security is lost when one realizes that by 1980 the world will consume the reserves of a Prudhoe Bay or a Libya, or Venezuela in less than a year, based on the recent predictions of U.S. and world reserves made by Eastman-Dillon, Union Securities Company(2). Recent forecasts of U.S. demand and source of supply made by Kenneth E. Hill of Eastman-Dillon are shown in Figure 1. This forecast shows a decline in domestic supplies (excluding Alaska) after 1973, with the total domestic supply leveling off in 1975 at about 13 million barrels per day. Since the predicted demand increases from about 14 million barrels per day in 1970 to about 20 million barrels per day in 1980, about 35% of domestic consumption must come from imports or non-conventional sources by 1980. More imminent is the shortage of low sulfur fuel oil which has been created by the new, tough air pollution regulations that are basically legis¬lating eastern coals out of the market. As an alternate to importing large quantities of low sulfur fuel oil or importing and desulfurizing regular fuel oil, one of two domestic solutions is possible: stack gas clean-up or solids fuel pretreatment. Stack gas clean-up may be the cheapest approach for old installations, but fuel pretreatment has real advantages for new installations. Coal pretreatment at the mine could eliminate all solids fuel handling

Jan 1, 1972

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By Robert T. Chapman

The revolution in equipment for blasthole drilling, ore loading, and ore hauling has been so rapid over the last ten years that it has generated an important new profit potential in the mining industry. With the new high-capacity machinery now available, it is possible for a mining enterprise to earn a profit from larger and lower grade orebodies than ever before despite the ever-increasing burden of rising costs. Just what such equipment can accomplish when coupled with improved mining practice has been demonstrated with startling success at the No. 1 mine of Minerva Oil Co. near Cave-in-Rock in Hardin County, Ill. The No. 1 is an underground operation which has been producing fluorspar and zinc ores and concentrates continuously since 1944. A few years ago, when the mine neared the familiar cross-roads where rising costs, increasing tonnages, and relatively static product prices converge, company officials decided to bolster the operation with new mobile equipment. They chose three machines which proved so effective that output at the No. 1 doubled between 1963 and 1965,while costs dropped by about 40% in the same period.

Jan 11, 1966

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

By W. W. Adams

The first full year of the second World War for the United States presented a picture of the metal-and nonmetal-mining 4 industry which, without proper analysis and explanation, would convey a distorted view of achievements during 1942, especially because employment at gold and silver (lode and placer) mines-the largest group-declined to such an extent that the over-all totals for the country were reduced even though increases were made at mines producing copper, lead-zinc, iron, miscellaneous metals, and non-metals. A complete panorama of the metal-and nonmetal-mining industry, exclusive of coal mining, reveals a decrease in the number of men employed, the man-hours of employment, and the accident-frequency rates. Were the gold and silver (lode and placer) mines to be considered as a separate category; it would be seen that the number of men employed at all the other groups of mines increased appreciably over 1941. These other increases must be considered important, since these mines produced the vital war minerals that made valuable contributions to the military successes of the United States and its Allies during the year. A separate analysis of each of the various groups of mines may be found elsewhere in this bulletin. For the purpose of maintaining continuity in this series of bulletins, however, the discussion in this introduction will be confined to the entire metal-and nonmetal-mining industry (excluding coal mining, for which a separate bulletin, No. 462, has been published).

Jan 1, 1945

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018

By R. V. Ramani

Minerals, together with agricultural and forestry products, are the primary source of wealth produced in the United States. Although the production of minerals requires only a small fraction of the state's total land surface, as compared with either agriculture or forestry (Table 1), mining activities generally are much more disruptive to the land surface, and rehabilitation is more complex and costly. The past 10 to 15 years have witnessed a sharp increase in mineral exploration and mining, particularly coal mining, which has brought with it an increase in conflict over land use and an increase in negotiations for purposes of mineral prospecting and mining. The general increase in the production and consumption of coal and the particular increase in the percentage of coal extracted by surface mining methods coupled with a growing nationwide environmental consciousness have created increased public concern and in some cases outrage over mining activities. Although there is ample evidence to indicate that it is possible to plan for and design mining activities in such a way that they are compatible with other activities and can thus be made a part of a sequential land-use plan, there is a general lack of knowledge regarding the importance of mining as the provider of basic and essential raw materials to supply society's constantly expanding and increasing mineral needs. This lack of knowledge extends to such matters as land and mineral rights negotiations, the character of mineral deposits and minerals, mineral economics, and land-use planning.

Jan 1, 1977

By Wayne W. Murdy

Since 1993, Newmont has been actively growing through the development of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru began operating in October 1993 at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau Joint Venture in Uzbekistan, the first of its kind in the CIS. In early 1996, Newmont started operating the Minahasa mine in Indonesia. Now, in early 1997, Newmont is undertaking the construction of a $1.9 billion project in Indonesia and is completing a feasibility study with our partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards, and Newmont has been very successful in all of them through risk mitigation programs including utilizing strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, utilizing World Bank, EBRD and IFC financing and building and maintaining strong ties with host governments. This paper describes in more detail, some of the risk mitigation programs that Newmont has used to successfully grow the company through development of major foreign mining operations.

Jan 1, 1997

By Jeffrey A. Aldinger

This U.S. Bureau of Mines report presents an analysis of surface coal mining accidents involving mobile equipment for the years 1989 through 1991. Mobile equipment is defined as haulage trucks, front-end loaders, bulldozers, scrapers, and road graders. These five pieces of mining equipment accounted for 20 pct of all surface coal mine accidents and 41 pct of the fatalities. The general discussion of these accidents covers the accident causes, the primary activity of the accident victims, and other contributing factors. A more detailed analysis of accidents associated with each piece of mobile equipment is also provided. This report will provide mine managers and mine safety personnel with a better understanding of the hazards associated with mobile mining equipment. It identifies where improvements in mobile equipment safety can be made and those areas requiring additional safety emphasis, such as safety training, work procedure changes, or engineering changes to the equipment or work environment. The analysis was performed by a team of researchers using accident data and narratives provided by the Mine Safety and Health Administration.

Jan 1, 1995

By W P. Breytenbach

"The phased application of statistical process control (SPC) infers that processes are classifiable as pre-SPC (or phase zero), phase I and phase II processes, with different objectives being pursued in the different phases. Phase zero processes, defined as processes affected by assignable causes of variation, are characterised as follows: out-of-control with unknown autocorrelation structure having an unknown statistical distribution not performing consistently on target with minimum variability potentially incapable of conforming to the product specifications. The objectives of phase I SPC is to obtain estimates of the mean (µ), variance (s2), probability density function (f(X)) and the autocorrelation structure, as well as transforming the process into a phase II process (defined as a process conforming to specifications and performing on target with minimum variability). As in any other type of research or pragmatic improvement intervention, sampling is required is to achieve these objectives. The challenge of deciding a phase I sampling plan is multifarious since it has to cope with the aforementioned effects of assignable causes and provide for rigour estimates of the unknown parameters. Furthermore, deciding sampling plans in phase I invariably presents a classical catch-22 situation: appropriate sampling is required to determine the autocorrelation structure of a variable, but knowledge of the autocorrelation structure is required to formulate an appropriate sampling plan. This paper suggests, for random variables, guidelines to formulate sampling plans, and presents a methodology to estimate the inherent process parameters of process variables and an approach to identify assignable causes in phase I. CITATION:Breytenbach, W P, 2014. Rational sampling and standard deviations for random variables in phase i application of statistical process control, in Proceedings Sampling 2014, pp 141–154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

SME's Annual Membership Report - 1961 Membership Directory

Jan 7, 1961

By Oliver Bowles

Limestone, including dolomite, is the most widely used of all rocks - nearly 300 million tons annually in the United States alone. It occurs in some form in every State and is produced in thousands of localities. Because of its attractiveness, substantiality, and durability it is employed extensively as a building stone. In crushed and broken form it is used for concrete aggregate and railroad ballast and in highway construction, metallurgy, agriculture, and a host of chemical and industrial processes. This paper proposes to furnish general information on the origin and occurrence of limestone and dolomite, chief production centers, major uses, and methods of quarrying and preparing stone for market. Footnote references will guide the reader to sources of more complete information.

Jan 1, 1956

By N Murthy

Alumina is a major impurity in Australian iron ores and as the higher grade ores become depleted there will be a stronger focus on treating lower grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the alumina content. High alumina in iron ore is deleterious in that it can:• produce slags with lower desulfurising capacity,• reduce sinter/pellet strength and quality, and• produce higher slag volume and increase slag viscosity.Meeting iron ore quality specifications for alumina by blending ore from different sources will eventually be insufficient. Hence, innovative flow sheets based on new and commercially available technologies will be required. Their advantages and disadvantages, the testing methodologies and the challenges and diffi culties involved in reducing the alumina content of iron ores are presented and discussed.

Jul 11, 2011

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By Mining Engineering

The 43rd Annual American Mining Hall of Fame Awards Banquet and Fundraiser, sponsored by the Mining and Minerals Education Foundation (MMEF), will be held Dec. 6 in Tucson, AZ. Each year, the MMEF honors a slate of individuals and companies who have made notable contributions to the advancement of the mining industry. This year’s distinguished nominees are: Kathleen L. Quirk, president and chief executive officer and a member of the board of directors of Freeport-McMoRan Inc. is the 2025 Hall of Fame Inductee. Quirk joined Freeport in 1989 and had responsibility for a broad range of corporate functions, including tax, investor relations, corporate development and treasury before being named chief financial officer in 2003. She was named president of Freeport in 2021 and became a member of the board of directors in 2023. As a senior member of the company’s executive team for more than 20 years, she has been instrumental in Freeport’s strategic planning and execution of company goals. During that period, Quirk was named Best CFO in Metals and Mining by Institutional Investor Research magazine on numerous occasions. She holds a bachelor of science in accounting from Louisiana State University.

Aug 1, 2025