Search Documents

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By J. Barrett

State-of-the-art wireless communication and location-tracking technologies will dramatically change the face of mine worker safety. The MineTracer System developed by a Liberty Lake Washington company is a broad capability wireless sensor network based on a new breed of technologies known as wireless mesh systems. In this paper, R&D Manager Jim Barrett summarizes the balance of engineering tradeoffs that result in a system that (1) performs well, (2) is survivable against many types of mine accidents, (3) operates for many hours post-accident on battery power, (4) meets stringent MSHA requirements for intrinsic safety, and (5) is economically affordable for the mines.

Jan 1, 2009

By W. T. Irvine

"The H.B. Mine, a zinc-lead operation of the Consolidated Mining and Smelting Company of Canada Limited (Cominco), is in south central British Columbia, on Sheep Creek, a west-flowing branch of the Salmon River. It is 3 miles by road from B.C. highway No. 6, 30 miles south of Nelson, B.C., with an excellent highway connection to the smelter city of Trail, 35 miles from the mine. The nearest permanent settlement is the village of Salmo, 7 miles distant by road. The mine is situated along a belt containing other important zinc-lead deposits, including those of the Canadian Exploration Company, 3 miles to the south, and the Reeves MacDonald mine, 9 miles distant again to the southwest.Deeply oxidized outcrops were located in 1907 on the north side of Sheep Creek valley by two prospectors named Horton and Benson. The property was given the name H.B., after the two discoverers, and there commenced a long and intermittent series of mining operations designed mainly to develop and extract oxidized lead-zinc ore. In 1925 a determined attempt was made by a British syndicate to develop a large tonnage of sulphide ore, but this ended in failure after some 3,000 feet of lateral development had been done. In 1927 Cominco acquired the mine, but it lay idle until 1946 when a geological study was followed by a program of surface drilling which encountered extensive sulphide mineralization. An underground development program revealed more details of the deposit, and sufficient ore was found to warrant construction of a 1,000-ton mill. Mine preparation and mill construction were completed by early 1953, but production was deferred due to low metal prices. The mine was finally brought into production early in 1955."

Jan 1, 1949

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

By Brian R. Zelenka

The Bureau of Mines (Bureau) reviewed all available information regarding geologic and depositional processes contributing to potential coastal and offshore platinum group metal (PGM) placer deposits around the Goodnews Bay Mining District. The Bureau found that favorable environments for PGM along with gold and chromite enrichment include: (1) buried paleofluvial channels; (2) recent paleofluvial channels with little marine sediment overburden, (3) beach deposits, particularly in the upper swash zone and near back beach environments; (4) paleostrand lines; (5) shoal lag deposits inside the mouths of Goodnews and Chagvan bays; and (6) bases of far offshore tidal ridges which may represent reworked glacial deposits. Limited geologic and compositional (assay) data prevent determination of deposit size and grade of PGM mineralization for each deposit class. Future geologic sampling requirements for demonstration of identifiable offshore and beach PGM-bearing placers are discussed. Beach and offshore sampling programs conducted by the Bureau in 1986 will contribute additional information providing verification of specific deposit classes.

Jan 1, 2011

By Greenwood J. N

This is the fourth paper in the series on Australian w,ar materials and the work was undertaken as part of the programme for producing hard carbides. It had been intended to determine the influence of tantalum and columbium' carbides in mixtures with tungsten carbide. Owing to other, urgent developments, it has not been possible to proceed with that programme.1. THE PROCESSING OF A TANTALITE ORE(a) The OreThe minerals in which tantalum and columbium most commonly occur are tantalite and columbite. These two minerals are the end members of an isomorphous series of tantalates and columbates of iron and manganese, but in nature the series grade into each other.Some of the best deposits of tantalum and columbium ores in the world occur in the north-west of Australia. Until recently tantalite low in columbium was the only mine~al in demand but discoveries of extended uses for columbium, e.g., addition of ferro-columbium to high chromium I steels inhibits intergranular corrosion (weld decay), have created a demand for columbite low in tantalum as weB. Both of these types of' ore occur in the Pilbara district in Western Australia and most of the ore mined is exported to America after a preliminary grinding and concentration by gravity.A sample from the Bynoe Harbour locality, west of Darwin, was used in this investigation. It consisted of coarse lumps of tantalite with quartz in minor amounts. Cassiterite w.as also present. A recent investigation!l) gave the analysis as:

Jan 1, 1943

By S. Kodama

Starting on a small scale, the equipment for processing synthesis gas to form liquid hydrocarbons was expanded to handle 100 m) 3/hr. This reactor was successfully designed and constructed, and a basis for future design methods was established. Because, however, this work was carried out on an empirical basis, it is felt that a more thorough theoretical study should be made in an effort to increase the efficiency of the process, particularly in the development of a simpler converter.

Jan 1, 1951

Battle Mountain Gold Company's Paj ingo Mine is the first gold mine developed by the Company in Australia. The Mine located in northern Queensland commenced operations in September 1987. The high grade epithermal orebody is selectively mined and processed through a conventional carbon in leach/carbon in pulp (CIL/CIP) plant at a rate of 200000 tonnes per annum. In 1988 it produced 61000 oz gold and 152000 oz silver. Inadequate preoperational development of non technical management and organisational functions often leads to inefficiencies that last well into the operation. The Pajingo experience in this regard is oaTple ented by those from a number of other recently commissioned small operations. A checklist is discussed to assist any future preoperational group in focussing their attention into areas that seem to be of secondary importance at the time but often have a significant impact on overall management efficiency later.

Jan 1, 1989

By Douglas G. Fox

Outputs from industrial activities planned in the Riley Ridge natural gas project are modeled to determine the potential locations of air pollution impacts on the Bridger and Fitzpatrick Wildernesses in Wyoming. The nature of modeling, especially with regard to its realism, is discussed. Alpine lakes which, along with their watersheds, have minimal buffering capacity are being studied because of their sensitivity to acidic deposition from proposed new air pollution sources. A hypothesis which relates a source's emissions to deposition and lake chemistry in a worst-case sense is presented. Research designed to test the hypothesis and reduce uncertainties is outlined and progress reviewed. Focus is placed on the meteorological transport and atmospheric deposition parameterization contained in the hypothesis.

Jan 1, 1984

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grind-ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1965

By R. L. Miller

"Why should we care about diesel quality amidst the complexity of mining for minerals? Mining companies use a large amount of diesel fuel in their worldwide operations, both for moving ore from the mine to the processing mills or transportation hubs, and to generate power for onsite processing. This creates a large carbon footprint and poses both environmental risk with the production of emissions, and public perception of how those companies do their business as stewards of the environment while incurring a huge fuel expenditure. To improve diesel quality and create incremental value and greater environmental stewardship, the opportunity is broken down into several segments: 1. Mining industry diesel consumption 2. Fuel quality issues 3. Impacts on operations, economics, and emissions 4. Potential solutions 5. How improved fuel quality saves fuel expenditures 6. Economics of improved fuel quality 7. Recommended testing process 8. Fuel quality analysis checklist MINING INDUSTRY DIESEL CONSUMPTION The average grade of mined Australian ore bodies has halved, while the waste removed to access the minerals has more than doubled over the last 30 years, thus increasing energy consumption by 70%, (http://eex.gov.au/industry-sectors/mining/). Energy consumption and intensity in mining and mineral processing is rising at around 6% per annum. The mining industry is a huge consumer of diesel fuel worldwide, and the SRS Rocco Report of 4 August 2014 gives a better picture of recent trends. To better understand the reasons to reduce both fuel costs and consumption, we need to compare metrics on the amount of diesel consumed per each ounce of gold produced over the last decade. The rate of diesel consumption in gallons per each ounce of gold produced for the top five worldwide gold producers has doubled in the last 8 years from 12.7 gallons per ounce in 2005 to 25.8 in 2013 as shown in Figure 1 below.This is caused by 1) lower ore grades requiring more hauls to get same amount of finished gold product, and 2) haul trucks moving ore from deeper sources in open pit and underground mines. For one large multi-national gold mining company, the 2005 waste rock / production ratio was 52 metric tons/gold ounce; by 2013 that ratio had grown to 113 metric tons/gold ounce per the same SRSrocco 4 August 2014 report. Using the metrics above, the top 5 gold miners used over 591 million gallons of diesel fuel in 2013. The cost of diesel in dollars per ounce of gold has increased from $30.48 in 2005 to $101.14 in 2013, an annual appreciation of 16.2% as shown in Figure 2 below."

Jan 1, 2017

By J. P. Powell

The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Mid continent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also. The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County, Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that could not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 1.36 million barrels of water had been injected.

Jan 1, 1953

By Pawan L. Sethi

Design and construction of deep foundations and basements is increasingly becoming more complex, as the density and frequency of urban development increases. This growth brings various associated challenges in the form of design considerations and construction challenges. This paper discusses some of the challenges routinely encountered as well as some specific complications in this area, based on author’s experience gained through exposure as specialist contractor (designer), consultant and specialist consultant, along with some information on how these challenges were overcome. The paper highlights some of the key aspects of design coordination and importance of having an awareness of the overall perspective. Examples will be used to illustrate practical problems and the approaches used to respond.

Nov 1, 2022

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By Lawrence W. Sott

This Bureau of Mines report presents several factors that currently enter into the design, manufacture, and testing of windows and lenses used in explosion-proof enclosures. Emphasis is also given to the sealing concepts for lenses. Criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure, rather than upon the minimum material properties of its constituents. Procedures for surface preparation of adherends are also discussed.

Jan 1, 1982

The nature of metallurgical engineering?applying and optimising chemical and physical processing of ores into useful materials?is reviewed. Important trends that shape the context in which metallurgical engineers practise are identified ? increased global production of primary metals, declining prices, environmental constraints, and increased property requirements of materials. A successful department of metallurgical engineering is one which employs a team of academic leaders to develop graduate engineers who are productive across the full range of metallurgical processing. Keywords: metallurgical engineering, primary metals, commodity prices, processing

Jan 1, 2003

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

Production scheduling of open pit mining is a key area as it deals with the management of operating cash flows of mining companies. The efficiency of long-term schedules is usually assessed with economic criteria such as net present value (NPV), discounted cash flow rate of return (DCFROR) and payback period, which are not sufficient on their own for revealing the complex picture of the decision-making process.This paper offers a thorough analysis of the most important contemporary criteria of long-term production scheduling, as way to provide the mining practice with a new approach to the decision-making process. The list of criteria includes technological, economic and probabilistic ones. A detailed case study is provided aiming to illustrate the applicability of the criteria for comparing the scheduling approaches regarding the economic interests of a mineÆs owner and contractor. The results obtained can be used for revealing new trends in the current methodology of open-pit production scheduling optimisations.

Sep 26, 2011

By Peter W. Lotz

Contents of: ?Sampling for Cyanide in Metallurgical Processes? ?Sampling at process level of operation ?Sampling at environmental level ?Sample stability and integrity issues ?each citing possible objectives, practical example and reasons for surprises Overall recommendations on sampling plans and procedures to maintain sample integrity

Jan 1, 2005