Search Documents

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2002

By J. A. Younkins, J. A. Brooke

In 1931 the Philadelphia Company acquired by lease several coal mines in southern Greene County, Pennsylvania. These mines were known as the "Dora," "Seventh Pool" and "Rosedale" mines in the Sewickley seam, and the "Rosemary," "Seventh Pool" and "Warwick" mines in the Pittsburgh seam. All these mines are in the immediate vicinity of Greensboro, Pa., with considerable river frontage on both sides of that village. The mines in each seam are contiguous and to some extent the properties in the two seams lie one above the other. In 1938 the property known as the "Sandy Run mine," in the Sewickley seam, adjoining the Dora mine, was purchased from the Fredericktown Coal and Coke Co. Altogether, by purchase and lease, the company gained control of approximately 3400 acres of coal land in Greene County, from which it was estimated that some 20,000,000 tons of coal could be extracted. Geology of Warwick Properties Both seams of coal outcrop along or near the river on both sides of the town of Greensbgro. They lie on the eastern slope of the Lambert syncline, near the southern end of the axis, consequently the predominant dip of the seams is away from the river, so that development for river handling has the unavoidable disadvantage of adverse grades for haulage to the outside. Predominant grades away from the river at right angles to the "butt" cleat of the coal average about 2.25 per cent dipping in a westerly direction, but local dips occur, which are considerably greater. Predominant grades parallel to the river and at right angles to the "face" cleat of the coal average about one per cent dipping in a northerly direction. Both seams of coal lie in the Monongahela formation, the Pittsburgh bed being the bottom measure of the formation and the Sewickley bed lying about 90 it. above. Approximately midway between the two lies the Redstone coal bed, which is generally thin and of erratic occurrence and therefore of little commercial value. It is mined only locally where it attains sufficient thickness. Sewickley Bed The Sewickley bed is commonly called the "five-foot" or Mapletown" seam, because in Pennsylvania it reaches its greatest thickness and has been mined most extensively in the vicinity of the village of illapletown, approximately one mile west of Greensboro. In the early development of the Warwick properties, which occurred near the river, the seam had an average of 5 it. 2 in. in height. As development proceeded away from the river, however, the height gradually decreased until the average height of the present workings is about 4 ft. 6 in. Present development is encountering lower coal

Jan 1, 1947

By J. A. Younkins, J. A. Brooke

In 1931 the Philadelphia Company acquired by lease several coal mines in southern Greene County, Pennsylvania. These mines were known as the "Dora," "Seventh Pool" and "Rosedale" mines in the Sewickley seam, and the "Rosemary," "Seventh Pool" and "Warwick" mines in the Pittsburgh seam. All these mines are in the immediate vicinity of Greensboro, Pa., with considerable river frontage on both sides of that village. The mines in each seam are contiguous and to some extent the properties in the two seams lie one above the other. In 1938 the property known as the "Sandy Run mine," in the Sewickley seam, adjoining the Dora mine, was purchased from the Fredericktown Coal and Coke Co. Altogether, by purchase and lease, the company gained control of approximately 3400 acres of coal land in Greene County, from which it was estimated that some 20,000,000 tons of coal could be extracted. Geology of Warwick Properties Both seams of coal outcrop along or near the river on both sides of the town of Greensbgro. They lie on the eastern slope of the Lambert syncline, near the southern end of the axis, consequently the predominant dip of the seams is away from the river, so that development for river handling has the unavoidable disadvantage of adverse grades for haulage to the outside. Predominant grades away from the river at right angles to the "butt" cleat of the coal average about 2.25 per cent dipping in a westerly direction, but local dips occur, which are considerably greater. Predominant grades parallel to the river and at right angles to the "face" cleat of the coal average about one per cent dipping in a northerly direction. Both seams of coal lie in the Monongahela formation, the Pittsburgh bed being the bottom measure of the formation and the Sewickley bed lying about 90 it. above. Approximately midway between the two lies the Redstone coal bed, which is generally thin and of erratic occurrence and therefore of little commercial value. It is mined only locally where it attains sufficient thickness. Sewickley Bed The Sewickley bed is commonly called the "five-foot" or Mapletown" seam, because in Pennsylvania it reaches its greatest thickness and has been mined most extensively in the vicinity of the village of illapletown, approximately one mile west of Greensboro. In the early development of the Warwick properties, which occurred near the river, the seam had an average of 5 it. 2 in. in height. As development proceeded away from the river, however, the height gradually decreased until the average height of the present workings is about 4 ft. 6 in. Present development is encountering lower coal

Jan 1, 1947

By P. L. Weston, S. E. Khalafalla

A systematic study was made by the Bureau of Mines on the effect of so me hypothesized accelerators for the process of wustite reduction in carbon monoxide. When small concentrations of promoter materials in the order of 0.69 at. pct were added to the reducible charge, the rate of reduction to iron was increased. Promotion phenomenon prediction was made in light of a suyface reduction mechanism with the aid of Vol'kenshtein's effect regarding the propagation of crystal lattice disturbances by small amounts of relatively larger interstitial ions. The acceleration produced by a typical promotor, such as potassiunl, increases with protnoter concentration up to a maximum, beyond which the reduction rate decreases. Concentration for maximum promotion depends on the nature and physicochemical properties of the promoter. The extent of reduction rate enhancement is found to be directly proportional to the atomic volume and electronic charge of the additive. DESPITE the enormous volume of literature on iron oxide reduction, very little is reported concerning additive or impurity effects on this important metallurgical process. The beneficial effect bf calcium compound additions on the reducibility of iron oxide sinters has been reported by Tigerschiold,1 vor dem Esche,2 and Edstrom. Doi and Kasai~ found that the addition of lime or limestone to iron ores helps to break up any unreducible compounds, such as fayalite or ilmen-ite. and thus free the combined iron for reduction. Schenck et al. 5 suggested that the increased reduction rate obtained when adding lime could be accounted for by the instability of wustite in the presence of lime. Acid-base slagging reactions resulted in wustite disproportionation according to The dicalcium ferrite formed will yield iron and calcium oxide during reduction. Regenerated calcium oxide dissociates more wustite. This mechanism has been used by Seths and white7 to explain their experimental results. Recently, Strangway and ROSS' attributed the calcium carbonate acceleration of iron oxide agglomerate reduction to increased porosity, both initial as well as that developed during reduction. Aside from calcium carbonate, or oxide, no other promoter was noted in the literature, except for a brief mention by Barrett and woodg on the effect of sodium carbonate and aluminate as activators for the hydrogen reduction of magnetite at 600°C. The present investigation systematically studied a host of other promoters, including calcium and sodium, in an attempt to elucidate the mechanism by which promotion takes place and to fit the results into a simple chemical model. To attain this goal, the effect of promoter physical properties, such as atomic volume, electronic charge, and concentration are related to wustite reduction kinetics in this paper. Wustite reduction to iron, rather than the overall hematite reduction, was chosen since this reaction is known to be the slowest, and hence the rate-deter mining step for the overall iron oxide reduction process. EXPERIMENTAL PROCEDURE Raw Materials and Their Preparation. The pure or impregnated wustite pellets were prepared from minus 400-mesh chemically pure hematite powders. A known weight of hematite was thoroughly and uniformly mixed with a calculated weight of the additive. The mixed paste containing 35 wt pct water was gradually heated from 400" to 1200° C and fired at 1200°C for approximately 4 hr in an air atmosphere. After cooling, the sinter was pulverized to minus 100 mesh and pelletized into minus 4- plus 5-mesh spheres. Pellets were fired, similarly to the paste mix, air-cooled, sized, and stored. An appropriate weight of the charge (20 g) was placed in a zirconia reduction tube maintaining a uniform oxide bed height of 1 cm and a cross section of 7.1 sq cm for all of the test runs. The samples were supported in the vertical reaction tube by a bed of fragmented insulating firebrick plus 3- to 6-mesh alumina beads. The hematite was then transformed to wustite by reduction with a 30 pct CO2-70 pct CO gas mixture at 1000°C in a globar furnace. Complete conversion to wustite was ascertained by a continuous infrared gas analyzer recording the CO-CO2 content of the effluent gas until no carbon monoxide was absorbed from the inlet gas, and inlet-outlet gas analysis remained constant for 30 min. The wustite sample was then reduced with 100 pct CO at 100WC. From the recorded data, an initial rate of reduction was determined by the initial slope of the graph percent reduction vs time. In order to estimate the accuracy of the data, five separate determinations of the reduction curve of pure wustite, under otherwise identical conditions, were performed. The maximum deviation from the average reduction at 14 min amounted to 2 2 pct reduction. This deviation corresponds to 3.8 pct variation based on the percent reduction of the sample. Aiiy impurity effect below the limits of this maximum deviation was considered a spurious result. If the effect exceeded + 4 pct, then it was considered as a positive one. Considerable care was exercised in determining the initial rate from the slope of the initial segments of the curve. Each reduction curve was examined separately on large graph paper and the best tangent to the curve at zero time was drawn. The slope of this tangent was taken as a measure of the initial fractional reduction per minute. Although the time required to reach 50 pct reduction may be of special practical significance, initial rate measurements are invaluable in fundamental studies. These rates provide a measure of the process kinetics on the initial

Jan 1, 1968

By R. D. Archibald

Currently, around 100 million tons of construction materials and aggregates are shipped annually by rail. And recently, producers are looking much more carefully at rail not only to reduce fixed costs through increased volume, but also to eliminate operating headaches, such as increasing community pressures about trucks on the road, noise and dust. Many producers are uncertain as to how to enter the rail shipping business since railroads have historically been reluctant to ship small quantities short distances. This article provides strategies to help producers examine and pursue moving their rock by rail.

Jan 1, 1995

By Jürgen Kretschmann

The European climate and energy framework for 2030 is highlighting the reduction of man-made CO2 by increasing the use of renewable energy to mitigate climate change. In this spirit, Germany has decided to erase the coal use as an energy source by 2038 completely. Inevitably, this strategy promises a feasible, responsible, and sustainable post-mining management, because 200 years of coal mining have created numerous challenges necessary to tend to once the mining ends. Thus, the Research Institute for Post- Mining (FZN) at the TH Georg Agricola University in Bochum, Germany, has developed a holistic approach to meet these postmining challenges including further expertise present at our university. Here, the four strategic research pillars are (1) technical geoecology and hydrogeology to avoid and mitigate risks underground, (2) geomonitoring to evaluate and protect the surface, (3) industrial heritage preservation and engineering to secure and reuse brownfields such as mine sites, and (4) economic transformation planning of mining regions to enable a prosper future for generations to come. In all efforts, we aim to achieve the fundamental goals of the UN to deal with the resources of our planet responsibly and sustainably. Furthermore, we are synergizing increasingly with national and international networks in the interest of social, economic, and environmental stakeholders.

Jul 23, 2020

By W. B. Burchall

Introduction In presenting this paper the author wishes to state that the opinions here given represent only his personal views. A general survey of the subject has been attempted, but such deductions as may have been drawn are not necessarily endorsed by the Company with which he is associated. The aeroplane as an instrument of transport is yet a novelty, for it is only twenty-five years since man first flew. This statement, by itself, may be very deceptive, for compared with the steam locomotive or even the auto-mobile, this infant in industry has made some remarkable showings. The 'actual performance' speed-curve of aircraft plotted over a ten-year period is rising faster than the 'expectancy' speed-curve of 1924 indicated, and it should be noted that, today, the possibilities of 600 miles per hour provoke less scepticism than did the prophecies of 400 miles per hour only a decade ago. Commencing with the remarkable achievement of raising one man into the air, aircraft with an all-up weight of 14 tons are now in daily use on the British airways, and recently a non-stop flight of 5,340 miles was accomplished in an aeroplane, without refuelling. More true than ever is the statement that the records of yesterday are commonplace tomorrow, for new ideas are today seized on and exploited to the utmost once the period of scepticism and doubt has been overcome. In fact, so many new ideas have been brought forward, during the past few years, and applied successfully in our economic life, that one may well ask if today we are not a little too impatient, too exacting in demands, forgetting that real worth-while progress -is attained by no short-cuts.

Jan 1, 1933

By J Hartog, V Beehan, D Beeson

Treating an ore blend from five different deposits at Newgold’s Peak Gold Mine (PGM) has always been a challenge due to the inherent variability between each of the orebodies.Operating the processing plant at PGM with a ‘normal’ level of process control and a good operations and metallurgical team has allowed the processing plant to achieve above the name plate design at 102 t/h and recoveries in the order of 92.8 per cent for gold and 88.4 per cent for copper.With a company value and culture of striving for continuous improvement, PGM implemented the Manta Cube® system, an advanced process control system, for the semi-autogenous grinding (SAG) mill, gold leach circuit and tailings thickener over a 12-month period throughout 2012 and 2013.The overall benefits of implementing the Manta Cube® system has led to an increase in mill throughput of at least two per cent, improved SAG mill liner life, a ten per cent decrease in cyanide consumption and a reduction in flocculant of at least 30 per cent with no detriment to the gold and copper recoveries.The entire project had a payback period of less than two months, and the combined benefits resulted in an overall increase in revenue of at least $5 million per annum. This is quite significant for a processing plant the size of PGM.This paper describes the methodology, overall results and economic benefit of applying the Manta Cube® system on-site at Newgold’s PGM.CITATION:Hartog, J, Beehan, V, Karageorgos, J and Beeson, D, 2014. Optimisation of the Peak Gold Mine’s processing plant through advanced process control, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Stuart Hammer

The mining industry has seen a flurry of merger and acquisition activity of late. Rising metal prices, increased spending on infrastructure in developing nations and the growing demand for companies to diversify have helped fuel M&A activity in this industry. Many analysts believe that the robust M&A activity will continue, particularly if the demand for mineral resources in India and China remains strong. Because prospective purchasers need to evaluate the various risks confronting target companies, acquiring mining companies requires a considerable amount of due diligence. Of these risks, environmental risk is critical and warrants significant analysis. The failure to properly assess environmental risks associated with remediation, reclamation, compliance or litigation can undermine the transaction. Such assessment is a difficult endeavor, however, due to several challenges that companies face when assessing environmental risks. To make matters more complicated, despite these challenges, many sellers ask buyers to assume all environmental risks with limited post-closing indemnification rights. This article addresses the most significant issues that commonly arise when conducting environmental due diligence and allocating environmental risk in connection with M&A transactions in the mining industry.

Jan 1, 2008

By Christopher R. Lattanzi

"Discounted cash flow analysis provides a means of relating the magnitude of expected future cash profits to the magnitude of the initial cash investment required to purchase an asset or to develop it for commercial production. The objectives of discounted cash flow analysis are to determine:.. The net present value of a stream of expected future cash revenues and expenditures... The rate of return which the expected future cash flows will yield on a given level of initial cash investment.In the case of mineral properties, discounted cash flow analysis is generally accepted as the preferred method of valuation, whenever sufficient data are available to permit its reasoned application. Sufficient data are required to support estimation of all of the individual elements of cash revenue and cash expenditure which will be associated with the development and operation of the property, up to the end of its estimated life. It is the accuracy of these input estimates which determines the validity of the resulting determinations of profitability and rate of return on invested capital.In undertaking any discounted cash flow analysis, it is important to recognize certain fundamental attributes of the mining industty:.. The basis of any mineral development is the existence of an ore reserve... Costs are determined by the number of tonnes mined and processed, while revenues are determined by the number of pounds or ounces of metal produced. The two are related by the recovered grade of the ore... Profit is typically more sensitive to changes in revenue than it is to changes in cost... Commodity price is a principal determinant of revenue, but it is also the factor with which is associated the greatest level of financial risk.In the end, of all of the factors which must be considered in the discounted cash flow valuation of a mineral property, the most significant are the reliability of the reserve estimate, particularly with respect to recovered grade, the price at which the product is to be sold, and the risk of not maintaining the projected level of price."

Jan 1, 2003

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By D. J. DeLeo

In recent years the hue and cry of American industry concerning the pressure of foreign competition on the domestic marketplace has become all too familiar to most of us, as we are all well aware, the steel industry has not been exempted from this pressure, reduced production levels, work force cutbacks, and in some extreme cases, plant closings and company liquidations have resulted, new regulations governing imports and quotas have been enacted, foreign trade agreements reached, and more strict regulation enforcement practices undertaken, despite these, and other measures, the impact of aggressive foreign competition has not lessened, the concensus of numerous management consultants is that in order to successfully cope with these problems we must draw on all available technology to provide the tools which will enable us to enhance our management effectiveness, one area requiring particularly close attention in any mining operation is that of managing critical resources - namely time, energy and equipment in a fast and efficient manner, In mining, with critical resources deployed over a large geographical area, any degree of success involved with resource management is dependent upon knowing the current status of all work related activities, if we, as mine operators, are to be more successful in this area, additional tools are a necessity and modern technology has provided a multitude of new options from which to choose.

Jan 1, 1985

By J. M. Demarthe

The recovery of minor metals from zinc concentrates is dependent on the process used for their treatment. The behaviour of gennanium and indium in pyrometallurgical processes such as the Imperial Smelting furnace or the cupola furnace is of practical importance. The .Anaconda process for the treatment of zinc leach residues is not well suited to the recovery of valuable minor metals, and new technologies must be studied. In this regard, a solvent extraction process, using Kelex 100, developed by Minenet Recherche for the recovery of gennanium from dilute sulphate leach solutions is described. Also, new hydranetallurgical techniques in chloride media can be applied to the purification and concentration of minor metals depending on the stability of their chloro-complexes and the valency of associated inpurities. A synthesis of methods is proposed to address the problems related to the recovery of valuable minor metals in the zinc industry.

Jan 1, 1990

By Rogério Martins Pereira, Charles Pierri de Souza, Lucas Gabriel Correa

The Tandem Cold Mill is composed by stands with rolls positioned so that the rolling force can be transmitted to the strip being processed. Due to the mechanical stresses inherent in the process, the roll bearings are heated and are equipped with lubrication and cooling systems. Nevertheless, there is the challenge of continuously monitoring the temperature of the bearings, which would allow preventive intervention in case of overheating. This paper presents an in-house solution to temperature measuring system applied to the backup roll bearings of a continuous Tandem Cold Mill. The system uses Zigbee technology and is integrated with the main control system, allowing early diagnosis of bearing heating and proper intervention. Results and features of the system are discussed.

Oct 1, 2019

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By Walter Miller

NOW, after a year's continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity- more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser one-) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture.

Jan 1, 1943

Over the past few years, there has been an emerging relationship between business and civil society, especially NGOs. This relationship has the potential to bring about significant change, identifying common ground between commercial and societal interests. The mining industry has been a leader in acknowledging the need for community consultation and engagement. This paper argues that partnerships can make a very significant contribution to the industry as it comes to terms with the dilemma of an open economic system pushing against a closed ecological system.The paper will pose a number of questions: where is the locus for debate about sustainability in the mining sector?; how well embedded within companies are the new competencies that Leon Davis first identified in 1995 for the mining sector?; how has education for mining engineers or exploration geologists changed to prepare people for what are very different expectations within the working environment?; how well is the industry doing in managing its own environmental impact and what is its responsibility to an agenda for sustainability which extends beyond its own operations?;and how can NGO partnerships contribute to more sustainable outcomes? The paper does not aim to answer these questions, but to explore them in the hope that the issues and possibilities raised will contribute to advancing progress towards sustainability within the industry.

Jan 1, 2002

"Only the coal of the Sunnyside district in Carbon County is coked. Two companies, the Utah Fuel Company and the Columbia Steel Corporation, operating adjoining mines at Sunnyside and Columbia, produce coke.The Utah Fuel Company has 819 beehive coke ovens at Sunnyside. Only 350 ovens are being operated at the present time, largely because the smelters which had been using Sunnyside coke changed their equipment from blast furnaces to reverberatory furnaces.The Columbia Steel Corporation operates a plant of 33 Koppers type by-product coke ovens at Ironton, near Provo. About 800 tons of coal are used per day to produce coke for the company's iron blast furnace plant pie ovens produce about 400 tons of coke, 12,000,000 cubic feet of gas, 9,000 gallons of coal tar, 3,000 gallons of benzol and several tons of ammonia sulphate per day.The total coke production for the State from the earliest output of record in 1880 until June 30, 1924, is 5,947,714 tons."

Jan 1, 1925

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932