Search Documents

By Vincent A. Scovazzo

Benchmarking is a business management process that seeks improvement through the study and reapplication of practices conducted by industry leaders. This discussion presents objectives and organization of benchmarking applied to mining geomechanics. Similar procedures have been successfully applied to mining companies, laboratories, and research organizations involved in mining geomechanics throughout the world. Benchmarking is a structured process that allows an organization to learn from the "best" in the field. The objectives of benchmarking vary depending on the company's targeted areas for improvements. Typical goals include ground control cost reduction, enhanced safety, optimization of geotechnical staffing, development of state-of-the-art design procedures, or the adoption of the "best in the field" geotechnical data management. Once the objective of the study is established and the practices and procedures to be benchmarked are identified, a benchmarking team is formed from internal and outside specialists. Benchmarking in geomechanics is fundamentally different than in most other fields because of the effects of local geologic conditions and regulations, both of which must be understood by all on the benchmarking team, before a comparative analysis can be made.

Jan 1, 2000

By Graham J. C. Carpenter, Marc Charest, Jason Lo

"The method of producing magnesium-based composites with silicon carbide (SiC) particulates embedded in the matrix of magnesium AZ9I D alloy by the squeeze-casting technique are described. This method involves the fabrication of a SiC particulate preform and the subsequent squeezing of molten magnesium into the preform. In this study, alumina, aluminum phosphate and a proprietary binder were used for the fabrication of SiC particulate preforms. The procedures employed in the fabrication of SiC! AZ9ID composites are presented, together with the results of characterization of the composites using optical and transmission electron microscopy. Special attention is given to the reaction products in the bulk alloy and at the interfaces between SiC particles and the AZ9ID matrix alloy.1. IntroductionInterfacial, microstructural and metallurgical characteristics play an important role in determining the mechanical properties of a composite. In theory, reinforcing magnesium with SiC particulates should provide an improvement in strength and modulus of the composite over the unreinforced counterpart. However, many factors resulting from the fabrication process can cause degradation rather than improvements to the mechanical properties. In particular, the interfacial characteristics are known to critically influence the properties of composites [1]. Before evaluating the mechanical properties of a composite, it is always useful to examine the microstructure, which is closely related to the mechanical behavior. This helps to reduce the labor-intensive steps of sample preparation for mechanical property evaluation, which can be particularly difficult as a result of the high hardness of composite materials, as well as providing a wealth of information on the microstructural and interfacial characteristics, particularly the reaction products caused by processing. This information is also pertinent in understanding the factors governing the mechanical properties of the composites.There are many factors which determine the nature of the interfacial characteristics of a SiClMg composites. Qualitative estimations of the interfacial bonding have been performed based on thermodynamics, electronic and electrostatic concepts. In addition, the kinetic conditions during the fabrication play an important role. From an interfacial energy standpoint, the driving force for the formation of a metal/ceramic interface is the decrease in free energy that occurs when intimate contact is established between metal and ceramic surfaces. The simple representation of the energy change per unit area of interface formed (~G) is given by Dupre equation [2]:"

Jan 1, 1996

Case studies from four western states are used to illustrate the impact of the environmental compliance process on the mining industry. The case studies were not chosen as a statistically significant sample of all mining operations in the western United States but were chosen as representative of operations on both public and private lands and in locations that exhibited varying degrees of involvement by governmental units, non-governmental organizations and the general public. Basically, each case study was chosen because some aspect of their environmental compliance process helped to illustrate an interesting point in the regulatory process. The criteria used to select the case studies were: mines located in different jurisdictional areas, mines located in varying geological areas~ mines located in areas having different historical relationships with mining: and operations that are in production as well as those seeking an operating permit. The variety of such projects should provide the necessary foundation to evaluate the impacts of the environmental compliance process in each location.

Jan 1, 1994

By Antonio Nieto, Jesus Castillo

Research and Development (R&D) departments in the mining sector are essential for creating new solutions on productivity, safety, and sustainability. Nevertheless, the selection of R&D projects is complex, often influenced by subjective judgments and uncertainties. This paper explores the application of the Multicriteria Decision Analysis (MCDA) as a structured approach to evaluate and prioritize innovation projects based on various criteria such as safety, cost, environmental impact, and social acceptability. By assigning weights and quantifying criteria, MCDA enhances decision-making transparency and objectivity. This study aims to show a method that facilitates strategic thinking, resource optimization, and stakeholder engagement, ensuring that selected innovations align with the company’s long-term objectives and commitment to responsible mining practices.

Feb 1, 2025

By John P. Mahaffey

Thank you Mr. Chairman, Ladies and Gentlemen of SME-AIM? for this opportunity to talk to you about, one of the most interesting and challenging facets of our mining industry. Because the need was then -we built in 1964 what is still today, one of the most sophisticated AC mining machine simulators for this or any industry. It simulated the electrical controls and circuits of an AC shuttle car. The student activated the controls on the main console, which represented the elementary control and power circuits. Its accompanying slide-tape program, student manual and worksheets provided our customers with an effective and highly motivational means to teach their face mechanics: 1. practical AC circuit and motor theory 2. print reading 3. troubleshooting techniques Nearly 10,000 men have put in over 100,000 manhours of training on the AC panel and its DC counterpart. The DC panel was modeled after the 14BU10 Loader. The success of these larger panels pointed out the need in our industry for an orangized, basic electrical program designed around mining machinery components & circuits. But probably more importantly, they brought to light the tremendous thirst for upgrading by our industry's employees. We then turned our attention to developing programs around very basic panels. The resulting programs were designed also to assure maximum student involvement.

Jan 1, 1975

The Bureau of Mines is the engineering arm of the Government for mineral resources. Its mission is to carry out laboratory and field studies that will assure the wise and effective development and use of our Nation's minerals, fuels, and underground domain in order to preserve the security and enhance the welfare of our people. Specifically, studies are directed to the means by which current and emerging demands may be met, the real cost of such achievements, and the assessment of related social and economic factors. Ways are sought to fulfill our material needs in a manner that minimizes occupational hazards to workers in the industry, reduces waste, and ensures that mineral raw materials are supplied and mineral-based products are used and are disposed of efficiently, without objectionable social and environmental costs. The headquarters of the Bureau of Mines is located in Washington, D.C. The Bureau's research and development program, however, is conducted at 19 research centers and laboratories located throughout the United States.

Jan 1, 1971

By Charles Taschereau

The statements made in this presentation contain certain forward-looking statements concerning potential developments affecting the business, prospects, financial condition and other aspects of Canada Lithium Corp. The actual results of the specific items described in this presentation, and the company?s operations generally, may differ materially from what is projected in such forward-looking statements. Although such statements are based upon the best judgments of Canada Lithium Corp. management as of the date of this presentation, significant deviations in magnitude, timing and other factors may result from business risks and uncertainties including, without limitation, the Company?s dependence on third parties, general market and economic conditions, technical factors, the availability of outside capital, receipt of revenues and other factors, many of which are beyond the control of the Company. Canada Lithium Corp. disclaims any obligation to update information contained in any forward-looking statement. Toronto Stock Exchange: CLQToronto CLQOTCQX: CLQMFOTCQX: CLQMF

May 1, 2011

By Ann Barron, Mark Abernethy

Along with the immense benefit of modern explosives seismic and acoustic effects caused by their detonation can be disruptive and alarming to many people. Claims range from affecting sexual performance to outright demolition of a residential structure. Regardless of the quality of the blast design and other precautionary measures, the inherent danger posed by the use of explosives often leaves residents searching for restitution. Consequently, many blasting companies today find themselves at the center of litigation. In the event that a blasting complaint proceeds to litigation your case will not be decided on “reasonable doubt” as in criminal trials. Instead, the jury will be instructed to decide guilt or innocence on a “preponderance of the evidence” presented. Even if you are able to present the best and most complete evidence that you have not caused the claim, the jury may rule in the favor

Jan 1, 2004

By Rene Steensma

The possibilities of the use of ultrasonics in the extraction of gold and silver is the subject of a study initiated in our laboratory since the beginning of 1986. The study consisted of various aspects of extraction, the results of which are in· different stages of advancement. Reduction in leach time combined with higher recovery are the most striking effects so far. The ultrasonics machine, originally part of a small pilot plant, forms now part of a much larger unit. This has the remarkable effect of even higher recoveries and shorter leach times. These data suggested a study on the possibilities of reduction of thiourea consumption. Although promising, the results of these studies require check testing and will be published as soon as our findings have been confirmed. During the study, which consisted of the application in thiourea and cyanide leaching, some interesting side effects were observed. In the first place, a reduction in penetration time which might make coarse grinding feasible. Secondly, an increase in compaction of the filter cake which reduces pregnant liquor losses, especially with clayey ores and industrial waste products. These will be studied under contract in the near future.

Jan 1, 1998

By Bernard Jones

LTUG ? A meeting of many mining companies that are using large tires ? Introduction of the mines and size ? Companies go over their usage of tires and performance ? As a group we discuss how the manufactures are doing with supplies and performance (who's running what sizes and manufactures they are using) ? The mine's best practices they use (which ones work for them and which ones don't) ? Where the mines see themselves going in the future ? What type of tire management the mines have in place

May 1, 2009

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By H. C. Lautenschlaeger

Let's start with a bit of History. Before the advent of woven wire screen cloth or perforated plate as we know it today, screens or sieves, as they were called, were probably made by the Greeks or Romans around the year 150 B.C. Coarse openings were made from bamboo or other woven reeds or with holes punched in leather hides, while fine openings may have been made using hair from the long tails of horses woven with small openings. The first metallic woven wire screens were probably produced by the Germans in the 15th Century. All of these screening devices were, of course, hand operated. The first records of mechanically driven shaking screens are found in "John Smeathon's Diary of His Journey to the Low-Country" in 1775. He was the English Civil Engineer who built the famous Eddystone Light House and discovered the formula for making hydraulic cements. He described a screen the Dutch were using as a wooden frame on which woven wire was mounted. This box was inclined at an angle and hinged on the lower end. The upper or feed end was equipped with a pulley so they could raise it up, say 5" or 6", and then let it drop abruptly onto a sill or stop plate, thus jarring the material deposited on the woven wire through the openings. Material that was passed over the deck was scooped up and redeposited on the woven wire for rescreening. This was an early form of what is today known as a recirculating load.

Jan 1, 1983

By Ernest A. Hersam

"INTRODUCTION.Luring the year 1923 a complete survey was made of the condition of research in the reduction (milling) and concentration of ores and nonmetallic minerals - that is, up to the stage where the ores or concentrates were ready for hydro- or pyro-metallurgical treatment. This survey was carried on under the general supervision of L. A. Lyon, assistant director and chief metallurgist of the Bureau of mines, in cooperation with the milling committee of the American Institute of mining and metallurgical Engineers, the Massachusetts Institute of Technology, and the University of California. Other institutions, including the National Research council, were of assistance and outlined recommendations during the study.While this report is on ""ore dressing"", it contains short sections on coal and clay. The mechanical handling that these minerals undergo is ""dressing"", so that ore dressing is inclusive of metallic and nonmetallic minerals. ""milling"", in its broadest sense, includes with ore dressing certain other metallurgical treatment which the report is not designed to cover.The survey revealed that considerable experimentation is being carried on great cost to the mining industry, but that the research is in general poorly coordinated while companies and firms are adequately taking care of routine tests and the mechanical features involved in their own operations, no comprehensive study of the fundamental principles of ore reduction is now in progress or contemplated. Many industries, besides mining, are interested in the preparation of materials for final treatment, rendering this investigation of value also to them. This class of fundamental research is neglected by industry unless there is some agency which can bring together at least a majority of this interested in a cooperative effort. It can not be effectively handled by a single company; and, moreover, no company can be expected to bear the whole burden of an investigation to benefit the entire industry or a number of industries hence there is need for concerted study within reasonable limits. Furthermore, co-operation eliminates duplication, which is largely a waste of effort and capital."

Mar 1, 1925

By P. J. K Leeuw, E. Uludag, M. J. Nong

Efficient drill-and-blast performance is pivotal to the profitability of deep-level mines, where high operating costs and declining grades demand maximum throughput. This study investigated persistent fragmentation problems at a longhole stoping operation that suffered from simultaneous oversized rock blockages in 300 mm × 300 mm grizzlies and excessive fines. Fifty-one muckpile images from five blasted stopes were analysed with Split-Desktop. Although the overall F₈₀ was 287 mm, nominally suitable for the grizzly aperture, the Rosin- Rammler uniformity index of 0.80 revealed a highly inconsistent size distribution containing both boulders and fines. Existing drill patterns were then evaluated with the Aegis underground software, which showed negligible crack overlap at the toe owing to inadequate spacing and burden. Insufficient energy overlap between blastholes, particularly at the toe, was found to contribute to the coarse fragmentation, while excessive fines were attributed to the crushing and severely fractured zones of blastholes. Optimisation simulations demonstrated that an 89 mm blasthole diameter on a 2 m × 2 m pattern would overlap, aligning with Aegis requirements of balancing powder factor, break angle, and energy distribution. Implementing this revised pattern is expected to reduce secondary breaking, prevent ore-pass blockages, lower fines, and ultimately improve overall production efficiency. The methodology illustrates how integrated image analysis and modelling software can effectively diagnose and address fragmentation issues, particularly in underground longhole mining, where challenging blasting conditions require a balance between achieving optimal fragmentation and maintaining stope stability. This approach offers a cost-effective pathway to improving comminution performance in deeplevel mines.

Oct 2, 2025

By W. Carter, P. Chaubal, K. Spaleck, M. Schoeman, J. Bobek, W. Seegers

Keywords: Pyrometallurgy, steel, hearth, blast furnace The Mittal Steel Company operates about 36 blast furnaces on four continents. Furnaces range from 1100 m3 to 4800 m3 inner volume. The focus of the group is to push for increasing productivity and increasing campaign life. This has been especially challenging, as many of these furnaces were not equipped for long campaigns during their prior rebuilds. Monitoring and operating practices have to be modified to match the new philosophy. Mid-campaign hearth repair strategies and hearth design philosophies have had to be reconsidered. The paper describes experiences with the current hearth designs and measures taken for hearth life extension. Additionally, the philosophy of recent hearth re-designs is discussed.

Jan 1, 2006

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By Alfred Weiss

These volumes report on the study initiated by the U. S. Bureau of Mines to develop and apply a methodology to quantitatively assess the probability and potential benefits of technological innovation over the next twenty-five years. The potential was recognized for new technology to solve copper industry problems in the United States. Objectives of the study were to: (1) Develop a methodology to obtain the opinions of mineral experts about future events -their likelihood of occurrence, and, conditional on occurrence, when and to what extent they are likely to occur; (2) Identify, select, and describe potential technological innovations which would have significant impact on copper production; (3) Implement the methodology and obtain the opinions of the mineral experts regarding selected copper technologies; and (4) Analyze the expected future benefits of successful technological innovations :n the copper industry. Although individual technologies are continuously examined throughout the copper 'community', this study is the first known comprehensive forecast of future copper technology. This study is also believed to be unique 1n that it represents the consensus opinion of over sixty expert copper technologists on the expected use of innovative technology in the industry over the next 25 years. The report is contained in three volumes.

Jan 1, 1983

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By Michael R. Kennedy

This report describes the demonstration of longwall mining in a seam dipping 27 to 34'. Equipment was selected on the basis of capability, compatibility, and co t. Snowmass, Bureau of Mines, consultants and manufacturers were involved in the selection process. The equipment arrived in early 1981, prior to completion of development for the first panel; therefore, the equipment was operated on the surface for training. The surface training paid off with a fast, efficient installation and start-up of the face. The longwall equipment operated very well on the steep pitch with an average equipment downtime of 21.9[9]. Coal handling outby the face was a problem which caused an additional downtime of 19.5%. Development for the panels proved to be the major problem in the economics of longwall mining on a steeply dipping seam. During the first 9 months of operation the longwall averaged 71.9 TPMS and development averaged 0.6 TPMS for an overall average of 14.1 TPMS. Had mining continued, timing of development would have been another major problem. Monitoring of subsidence, pillar stability and shield loading was done in connection with mining, but little useful information was gained from the monitoring.

Jan 1, 1987