Search Documents

By W. B. Morrison

The principal factors influencing the total percent elongation of a lead-tin eutectic and several low-alloy steels which exhibit superplasticity were investigated. These factors are: a) Strain-rate sensitivity of the stress (m). b) Specimen geometry; in particular, diameter-to-length ratio (d0/l0), and surface irregularity (e.g. notches). A feature of the tensile deformation of a superplastic alloy is the early appearance of a neck which continues to extend throughout the test. As a result the total elongation is directly related to the diameter-to-gage-length ratio. The strain-rate sensitivity of the stress varies during extension, mainly because of microstruc-tural changes. A satisfactory correlation exists between the minimum strain-rate sensitivity and total elongation, as indicated in the equation shown below. Notches cause a considerable reduction in total elongation and their effect is greatest at high values of strain-rate sensitivity. An initial notch depth exists below which there is no appreciable effect on elongation. An equation relating elongation to strain-rate sensitivity and specimen geometry is proposed, THE total percent elongation of a tensile specimen is usually regarded as a measure of superplasticity. However, little attention has been given to the fact that total elongation is also a function of specimen diameter and gage length, even though the importance of geometry has long been recognized in the tensile testing of materials in which elongations are relatively small.* In the present study, the effect on superplas- tic extension of the ratio of specimen diameter to length was investigated and an analysis was made of strain distribution along the gage length. Superplastic alloys are characterized by having a flow stress sensitive to strain rate but relatively insensitive to strain.2"' In an earlier study,5 it was found that the strain-rate sensitivity of several low-alloy steels changed during the test and that the minimum value correlated best with total elongation. In the present study, the variation of strain-rate sensitivity during the straining of a lead-tin alloy was investigated. EXPERIMENTAL PROCEDURE Lead-tin eutectic alloy (32 pct Pb 68 pct Sn), made from high-purity lead and tin, was cast in the form of 1-in. diam rod. The rod was cold-rolled in stages to 0.25 in. diam and then swaged to 0.125 in. diam. Samples were cut from the rod at various stages of the mechanical working process. Tensile test specimens were then made by attaching threaded steel ends to the rods by an epoxy-base thermosetting adhesive which required a setting treatment of 2 days at room temperature. The rods were seated in the steel ends in holes approximately 0.01 in. oversize. The test pieces thus made were of various diameters and gage lengths. These were stored at a temperature of about -70°C (-94°F) until required for testing. The distribution of strain along the gage length of a specimen was determined at various stages of the tensile test. The lead-tin alloy was superplastic at room temperature and direct observations during testing were simple. The gage length was divided by reference marks into five initially equal units. These reference marks were made with ink and were reinforced during the test when the initial marks became faint. Photographs were taken, at intervals, of the deforming specimen and measurements of the elongation in each of the gage units were made on these photographs. Tests were also done on several superplastic low-alloy steels whose properties were described earlier.5 The chemical compositions of these steels are given in Table I. A diagram of the notched tensile specimen used in the steel tests is shown in Fig. 1. The specimens were tested at 900°C (1650°F) in a furnace through which a mixture of He + 2 pct H was continuously circulated.5 RESULTS Strain Distribution. Approximately 20 tests on lead-tin alloy specimens were conducted to determine the strain distribution during the test. An example is shown in Fig. 2 of the strain distribution in the gage

Jan 1, 1969

By J. B. De Hart

This paper has been confined to the consideration of the working of thick seams, from six feet to sixteen feet, which are pitching at about thirty degrees to the horizontal. The discussion has been limited to these set conditions because they are the ones of commonest occurrence in the Southern Alberta bituminous coal district, because, from the point of view of safety, thin seams are more easily worked, and because a discussion of all the possible combinations of thick and thin seams pitching at angles varying from zero to ninety degrees with the horizontal would involve a task impossible in the time available. It has been assumed that the mine makes gas freely and that the coal is friable and tends to make inflammable dust which is highly explosive. Since the problem requires the taking into account means of maintaining a high proportion of lump coal, it is further assumed that lump coal commands a price considerably higher than the price which can be obtained for run-of-mine or for slack coal. Figure 1, tabulating the various factors which must be considered and their relation to each other, indicates diagrammatically the complexity of the problem. Any method of working becomes divided into two distinct components, the active workings of the mine and the old abandoned workings. While these are in a measure distinct, they are nevertheless inter-related, as shown in the diagram.

Jan 1, 1930

By John R. Dudo

The Bureau of Mines Morgantown Petroleum Research Laboratory, with the cooperation of the Penn York Oil Company, cored the Dewdrop, Bradford Third, Lewis Run, and Sartwell sands in the Sartwell oilfield, McKean County, Pa. This report contains a review of the geology and depositional history of the field and an evaluation of the feasibility of secondary recovery of oil from the Bradford Third and Sartwell sands by waterflood or gas drive. Core analysis, geologic data, and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Reservoir geometry, rock properties, fluid characteristics and saturations, and relative permeability-saturation relationships were used to assess the floodability of these two sands. The results of this study indicate that between 53,000 and 61,000 barrels of oil can be recovered by water or gas injection. The success of a waterflood or gas drive will depend on the field injection rates of the reservoirs comprising this oilfield. Following an economic evaluation, additional field work is recommended to further test the floodability of the reservoir.

Jan 1, 1967

By AIME AIME

OCTOBER will be western month for the Institute. With meetings at Spokane, Tulsa, Los Angeles, and San Francisco, and with a large number of American Institute of Mining Engineers members and their families in the party sailing out through the Golden Gate to Japan on the afternoon of the tenth, the major activities of the Institute will, for this month at least, be west of the Mississippi. Despite cancellations due to necessity, most of the officers of the Institute will be present and taking part in some one or more of the Western meetings. Prof. Robert S. Richards, our senior past-president, will attend both the Spokane and San Francisco meetings and then go to Japan. President Bradley will preside at the San Francisco meeting and then head the party going to Tokyo. At Tulsa and Los Angeles, the principal officers of the Petroleum Division will be present and active and at all the meetings, directors, ex-directors and -present and past officers will be on the job and keeping things moving.

Jan 1, 1929

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987

By Abrahan Barriga

The present study demonstrates the feasibility of the ultrafine grinding and atmospheric leaching process applied to refractory gold concentrates from Salave Project located in northern Spain. At bench scale, it was found acceptable sulfide oxidation was about 84-85% and CIL gold recoveries between 95-96% applying specific energy consumption between 30 and 60 kWh/t during ultrafine grinding. The atmospheric oxidation of the sulfide concentrate was controlled between pH 4.4 and 4.8 with a mixture 90/10 of CaCO3/NaCO3 with residence time of 48 hours for the atmospheric oxidation and 30 hours residence time for the CIL process.

Sep 30, 2022

By D. M. Jepsen

One of the first things we tell a potential new client is that they have only one chance to make a first impression with an Aboriginal community; all future communications and engagement will be predicated on that first impression. The key components of this most critical meeting are not your power point, your maps, or your draft plan for development ? they are instead a genuine, evident and clear demonstration of a sincere desire to develop a positive relationship that is based upon respect, and consideration and understanding of local communities and their interests, needs and desires. Relationship building is the foundation of proactive and positive consultation and accommodation with Aboriginal communities and the tone is set with the first meeting. C3 has refused more clients than we have accepted due most often to the fact that relationships between the company and the Aboriginal community have already devolved into a tense and toxic scenario. Land access and tenure certainty for exploration and mine development is critical to the foundation of a healthy, sustainable and environmentally and economically sound mineral exploration and mining sector. Without certainty confidence to invest in mineral exploration will be severely eroded. We all understand that substantive investments in exploration are required to increase the possibility of discovering, defining and developing new mines. The development of positive relationships based on a shared commitment of understanding, mutual respect and trust by Aboriginal Peoples and the mineral sector can provide the required business certainty and deliver social and economic benefits for local Aboriginal communities.

Jan 1, 2012

By R. Minnitt, C. Morgan, D. Fourie

The problems associated with outliers and their adverse effects on resource estimation in deep level South African gold mines are presented, and solutions suggested in available literature are reviewed. Traditional Witwatersrand type outlier capping uses the 99th percentile grade as the upper limit, a somewhat blunt approach. The occurrence of high and low grade areas in mining operations and the estimation of resources using geostatistical techniques require that the assumption of stationarity be upheld. Honouring the stationarity of data requires that mining areas be subdivided into appropriately sized and spaced domains. In order to overcome high-grade conditionally biased block estimates, the overly strong influence of extreme grades is mitigated by using naturally occurring grade sub-domains, by identifying outliers within the grade sub-domains, allocating relevant capping limits, and weighting them in a post-estimation process to. Rather than applying a capping value across a domain it applies a maximum cap based on the extreme value and its range of influence; the method also ensures that relevant capping occurs even in lower grade sub-domains. The proposed method for capping outliers recognises that metal contained in high grade chip samples should not be over-capped, and based on the grade of surrounding samples. The post-processing method of capping outliers does not interfere with the kriging equations. The method is simple, elegant, and can be easily applied. An advantage is that the output from the kriging process is not overwritten, allowing for comparison between original kriging results and post-processing results.

Sep 1, 2021

By A von Johannides, G J. van Hout, L F

In the past various systems have been used to plan the extraction of ore from block cave operations. These systems have varied from rather sophisticated models with empirical ægravity flowÆ rules applied to the very rudimentary models where only the recorded mined tonnageÆs have been accounted for against the available resource. The normal requirement of these models has been to only plan the movement of ground through the drawpoints. Little cognisance has been taken of the other parameters that affect the total mining operations. The intended purpose of the linear program planning system is to not only include the management, resource availability and geotechnical constraints, but to also include the mining rules. The paper will discuss the various constraints that have been considered, and attempt to illustrate where the system better serves the production system than previous ones. A brief technical discussion on the linear programming system is included.

Jan 1, 2000

By H. C. M. Gordon

IT is essential to the success of any mining op::ration that the roadways through which the material wrought and ocher materials and supplies are to be transported should be kept in such condition that this transportation cart be effected rapidly and without difficulty. The longer the roadway and the greater the tonnage to be taken over it, the more necessary it becomes chat the construction and maintenance of the road be such chat traffic delays can be reduced co a minimum. le is proposed co deal with the development and construction of roadways serving longwall operations and, since a recreating system of longwall is worked, as a rule, only where roadways driven in the solid coal can be readily maintained, the discussion will be confined co advancing longwall roads which are driven through areas from which the coal seam has been totally extracted. In order to construct a roadway through extracted ground in such a manner that it will remain in a state of reasonably good repair without undue maintenance, it is necessary chat everything possible be done to bring the overlying strata co a state of equilibrium as quickly as this can be effected, and the operations should be so planned that future workings will not disturb the equilibrium so set up more than can be avoided. Obviously, the readiest way to obtain a stable roadway is to develop it by tunnelling through a settled waste. However, this cannot always be done, as some of the roadways must be developed and constructed as the walls progress, but level or lateral cut-offs can be constructed in this manner. Main-slope roads can be developed in a similar manner after the coal has been extracted and a waste formed for at !east five hundred feet on either side of the line of the permanent roadway from temporary subsidiary roads developed for this purpose along one or other of the flanks of the waste to be formed. This interval must be obtained in order chat the lacer extraction of the seam will not set up movements in the waste immediately overlying or adjacent to the constructed roadway, thus upsetting the equilibrium of the strata and distorting the road.

Jan 1, 1940

By George B. Langford

ON THE QUESTION of postwar controls there are today three schools of though ; some advocate state control of everything the socialists ; second are those who advocate the removal of all governmental control over industry - the freedom of enterprise ideal ; and third are those who advocate a middle course - sufficient control to stabilize economic and industrial life, and to prevent violent fluctuations such as we saw in the interwar years. I advocate this third course. I firmly believe un free enterprise, but not in freedom of enterprise, or laissez faire, and there is a great and significant difference between these two.

Jan 1, 1944

By Jan M. Mutmansky

Simulation is a general term which commonly appears in the technical literature and which can have different meanings to different people. One interesting definition (9)* applicable in an engineering context is the following: "Simulation is the use of a model to study a problem." In most cases, the model referred to in the above definition is a simulation model constructed in a computer language and implemented on a computer in order to solve the problem under consideration. The application of computer simulation models to the study of problems in materials handling and earthmoving has been successful in the past. Generally speaking, this method has been used where the system to be studied has many variables and where the ability to predict the outcome of the system under different sets of conditions is difficult. The prime reason for using such a model is to evaluate the numerous likely ways of operating any particular system without the necessity of actually conducting full-scale field tests. The simulation model presented here is such an application made to the process of tunneling and, in particular, to the process of tunneling with a boring-type tunneling device. At first glance, the process of tunneling may not appear to be particularly complex and susceptible to study by a computer model. However, a close analysis of the tunneling process will reveal that it is rather complicated as a result of limitations placed upon the system by restricted space in the tunnel, geologic variations along the tunnel

Jan 1, 1972

By Fred C. Bond

It sometimes happens that old knowledge is forgotten, or half-forgotten, and its rediscovery is hailed as a great new advance in technology. Autogenous grinding affords such an example. The oldest-or apparently the oldest-commercial application of continuous autogenous grinding on a large scale outside of South Africa occurred at San Juancito, Honduras, where a total of more than two million tons of silver ore were ground autogenously with complete success from 1918 to the early 1940's. The history of the San Juancito silver deposits begins in 1880 when- the New York and Honduras Rosario Mining Co. started mining silver at a rate which soon reached two million ounces of silver annually. In 1912 the Company's first mill, located in the village of San Juancito, was shut down and its equipment transferred to a new cyanide plant. This plant, constructed on a mountainside near the mine, was equipped with tube pebble mills in which Normandy or Danish pebbles were used initially.

Jan 5, 1963

By Georgene Renner, Chee Theng, William Gleason

"A walk through the exhibit hall or a glance at the technical programing that was offered at the 2019 SME Annual Conference & Expo and CMA 121st National Western Mining Conference in Denver, CO, Feb. 24-27 makes it evident that the mining industry is an innovative one that is on the cutting edge of technology. However, a glance at the nearly 6,700 attendees of the conference and it is also evident that while the industry is moving forward at a rapid pace in some areas, it is lagging behind in terms of diversity, both in gender and ethnicity.At Monday morning’s keynote session, Hannah Ubi, a millennial and a public speaker who joked that she is the proud owner of a sixth-place swimming trophy and a number of participation medals, addressed a full house that consisted of many men with gray hair or balding heads. The issue of an aging workforce that is rapidly being depleted by retirements is not a new one for the mining industry. In fact, it has been a concern for the industry for more than a decade. The central question has long been, “when the current senior-level people begin to retire, how do we replace them, and how do we fill the knowledge gap that is walking off into the sunset?” SME has been on the front lines in searching for solutions to the impending problem and, along with industry partners, has worked hard to develop programs that will address these issues. Among other efforts, the Society has developed a Ph.D. fellowship program to encourage people to remain in academia to teach the next generation and to help train the next generation to take over in the private sector.“The SME Foundation’s Ph.D. and Career Development Grant program is exceeding expectations at this point with two Ph.D. students graduating and taking a position in academia and two professors achieving tenure,” SME Executive Director Dave Kanagy said during the conference.The Society’s Minerals Education Coalition (MEC) has done its part to help educate future generations about the mining industry with initiatives like EngineerGirl, the Boy Scout Merit Badge and Move Mining, the Shark-Tank-style competition that was held on Monday with five finalists competing for the top prize (ME, April 2019, page 53)."

May 1, 2019

By Milton Fies

ALTHOUGH pig iron from iron ore and red cedar charcoal preceded the mining of coal by many years, for tradition says that Alabama iron was used to shoe the horses of Andrew Jackson's soldiers, coal was not produced until 1830. In that year, coal was mined in Tuscaloosa County, in the vicinity of what is now the University of Alabama, and shipped on flat boats (obviously during the wet season, for there were many shoals) down the Warrior River to Mobile. About that time, the first railroad, the Decatur & Tecumseh, was being constructed in northern Alabama to overcome the obstructions to freight traffic caused by the now well-known Muscle Shoals in the Tennessee River. This railroad was patterned after a railroad at Mauch Chunk, Pa., which was used for hauling anthracite from the Panther Creek valley. The Alabama railroad, which required about four years to complete, was 46 miles long and was used solely for the transportation of cotton. Although it was a failure, it demonstrated the practicability of the undertaking, and the succeeding railroads, which were begun in 1834, 1848, 1852, and 1853, added immeasurably to the development of the coal resources of the state. Between the years 1830 and 1860, practically all the coal mined in the state was dug from the outcrop near the river or from the river beds, and shipped by boat to Mobile. Transporting coal down the Warrior River was one of great risk, required much skill, and frequently had heavy losses. It is recorded that this coal was sold to the gas company in Mobile in 1844; it was most likely mined from the Black Creek Seam. In 1914, on the completion of Lock 17, the Warrior River became a navigable stream from 9 miles above Cordova, Ala., to Mobile and offers a great opportunity for the future development of the coal resources of the state.

Jan 9, 1924

The following paragraphs have been extracted from a recent publication of the U. S. Department of Commerce; Miscellaneous Series, No. 65, " German Trade' and the War, " which portrays the industrial, commercial and economic conditions of Germany, at the present time, and has been compiled largely from sources published in Germany. Iron and Steel The Krupp company, the greatest of the German munition works, was faced at the outbreak of the War with the disappearance of its great international business, but this was amply compensated by orders from Germany and her allies, and the activity of the company has been greatly extended. The general meeting of December 1914, voted an increase in the capital to 250,000,000 marks. The gross profits of the company, amounting to 61,900,000 marks in 1912-13, have been more than doubled during the war. The gross profits were 128,260,000 marks in 1914-15 and 143,360,000 in 1915-16. Large sums have been written off; 10,000,000 marks have been placed in the pension fund during the war, and 5,000,000 were appropriated for workmen's dwellings in 1915. Thirteen million marks have been devoted to war assistance in the last three years. The assets of the company were valued at 967,000,000 marks at the end of 1916. For the year 1916-17, the company paid a dividend of only 10 per cent., but set aside 85,425,000 marks for depreciation. The Bismarckhütte in Upper Silesia, capitalized at 16,000,000 marks, with a bonded indebtedness of 7,907,500 marks in 1913-14, reported 3,912,000 marks of net revenue from operation for that year. During the three years of war the revenue increased successively to 8,077,000, 11,805,000, and 16,994,000 marks. While the capital remained unchanged, and the bonded indebtedness was but slightly reduced, the dividends paid during the last four years were increased from 9 per cent. in 1913-14 to 15, 25, and 30 per cent. during the war. During the year 1916-17 the amount written off, chiefly on the works and plant account, was 10,553,000 marks, or nearly as much as the total set aside during the three preceding years. The turnover for that year reached a sum many times the amount of the capital. At the end of 1916 the company's shares were quoted at 275, as against 144 at the end of 1913.

Jan 8, 1918

By A Garvie, D Kentwell, J Chapman

"Most new mining projects require an initial assessment of the locations and volumes of potential acid forming (PAF) waste that is likely to be moved and dumped in surface waste stockpiles. This requires sampling of the waste rock zones and submitting the samples for a series of tests. Key to the outcome of the waste characterisation process is obtaining sufficient samples that are representative of the various rock types both in number and spatial distribution.Various regulatory bodies throughout Australia and the rest of the world are currently struggling with how to define minimum amounts of sampling to achieve realistic estimates without imposing excessive costs and time constraints on a project.This paper addresses two aspects of the process: what constitutes a æsufficientÆ number of samples how to use those samples in determining volumes of likely PAF material.Geostatistical methods of characterising orebodies with large numbers of samples are routinely used in the mining industry by geologists and geostatisticians to estimate and classify Mineral Resources. In theory exactly the same methods can be used to estimate PAF waste locations and volumes.In practice the number and spatial distribution of dedicated PAF waste samples at feasibility stage is typically so small that it is almost impossible to estimate the spatial distribution of PAF material with any degree of confidence at all. Consequently, the common approach is to characterise a few samples from a lithological unit and then assume that they represent the unit as a whole. This approach, however, can be fraught with risk.This paper describes some of the findings of SRKÆs evaluation of several coal projects with respect to PAF waste evaluation and highlights some common misconceptions held by people working in this area that do not have a knowledge of statistics or geostatistics.CITATION:Kentwell, D, Garvie, A and Chapman, J, 2012. Adequacy of sampling and volume estimation for premining potential acid forming waste evaluation using statistical and geostatistical methods, in Proceedings Life-of-Mine 2012, pp 79-88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By William F. Boericke

THERE was a time when the selection of fire brick was .left to the judgment of the head bricklayer of the plant, whose choice was not unaffected by a box of Christmas cigars from a friendly salesman. But the days are past when it was generally believed, with complacent philosophy, that bricks were bricks without much distinction, and should be bought on a price basis alone. Gone, too, is the belief that in certain types of industrial work the eventual failure of refractories was assured. Modern metallurgical practice, with its trend toward handling larger tonnages at higher temperatures, demands the use of refractories that cannot be supplied by random guess. The logical development is to inquire into the properties of the brick to be purchased, and this resolves itself into the use of specifications. In 1925, the General Refractories Co., with the active support and hearty cooperation of some of its larger customers, established a laboratory, at its Baltimore plant, for testing and research in refractories. This was the outgrowth of a growing appreciation of the value of research in the refractory field. Since then the work has become more involved' and the aims more ambitious, so that the present laboratory now employs a staff of 11 men working, under the direction of trained refractory technologists, on problems of research as well as the routine control of manufacture. It is believed s that `this type of laboratory is a comparative novelty among refractory manufacturing plants. It handles the testing and research work for all the 15 plants of the organization. Being at one of the works has the advantage of making it possible to carry on large scale plant tests on new products after the preliminary laboratory tests have been successfully completed.

Jan 1, 1929