Search Documents

By R Osterman

As mining companies have to go deeper in search of ore and coal, the importance of protecting the highwall increases. Wall fatigue also increases with importance of the long life expectancy of a highwall, in particular the impact of fatigue influenced by resonance. Resonance is the tendency of a material to oscillate with greater amplitude at certain frequencies when exposed to a periodic force. Until recently, only dominant frequencies, either natural or induced, were all that could be measured through the fast Fourier transform of the blast-induced wave form.This paper presents a novel method to accurately predict the resonant frequency of a highwall. In fact, the method can predict the natural frequencies between any two monitoring points placed in line with the source of impact, and as such it can be used to determine the resonant frequencies of any physical object. The method not only predicts the resonant frequencies of the material; it predicts the structural response of the total frequency spectrum. This method helps describe the response of a mechanical structure to excitation. It describes the structure’s efficiency in the use of energy, that is, whether energy is dampened or consumed in resonance.The initial predictions have been so accurate that it made it possible to determine the fundamental frequency and the first six harmonics of a highwall in a northern Queensland coalmine. With the use of electronic detonators, the blast can be timed with a repeating delay to create an induced artificial frequency that has been determined to retain the least amount of energy.CITATION:Osterman, R, 2015. Transfer function – new method to accurately predict resonant frequencies of a highwall, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 233–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By F. Baerhold

Recycling of hydrochloric acid from the pickling of mild steel using pyrohydrolysis is a state-of-the-art technology. Recent developments have focused on the production of a high value iron oxide by-product, where the chemical purity and physical properties are the main issues. New processing routes, especially for TiO2 and Ni production, use leaching operations with hydrochloric acid. The feasibility of those processes depends on the availability of an economic and reliable process for the recovery of the acid. Depending on the level and type of impurities and the required specification of the by-product, pyrohydrolysis in a fluid bed or in a spray roast reactor can be the ideal solution. In stainless steel annealing and pickling lines, a mixture of nitric and hydrofluoric acids is used to remove the scale from the surface after heat treatment. Nitrate emissions from the pickling and the rinsing processes have to be avoided because of more stringent environmental regulations. An annealing and pickling line that is totally wastewater-free was developed, where not only the nitric/hydrofluoric acid but also the rinse water, is completely recycled. New developments to increase the HNO3-recovery rate and to obtain a metal oxide by-product that is easier to recycle are presented.

Jan 1, 2006

By P. Zhang

This paper gives a review of promising technologies for phosphate processing, and covers flotation, analysis and process control, as well as tailings treatment and utilization. Air bubbles of less than a µm in size, combined with relatively large bubbles, have been demonstrated, both in the lab and on a pilot scale, to improve flotation dramatically, by reducing reagent use while improving product grade. Innovative use of polymers has allowed rapid dewatering of fine tailings with a final product that does not segregate. The first online laser-induced breakdown spectroscopy (LIBS) analyzer was created, allowing rapid analysis of wet samples using the laser technology. Many large commercial projects are successfully pursuing the utilization of phosphogypsum.

Feb 1, 2012

By K. Eklund, T. Ahokainen

The Flash Smelting process is the most used production method for primary copper in the world. The basic idea of the Flash Smelting is to utilize the thermal value of sulfidic concentrates and melt the reaction product, in controlled conditions, without a need for external energy. This basic principle is utilized both in matte smelting and in Direct-to-Blister Flash Smelting Processes. In this paper, the behavior of normal (CuFeS2) concentrate of FSF-process is compared to the behavior of high grade feed material produced by Outokumpu Concentrate Upgrade Process with the aid of computational fluid dynamics (CPD) simulation using add-in subroutines developed by Outokumpu Technology. Results consist of the information concerning the behavior of the suspension, reaction efficiency and other parameters concerning the reactions of the feed material. It will be shown that, using the Upgrade Process, the throughput of copper from the Flash Furnace can be almost tripled.

Jan 1, 2007

By Pieter-Jan Kleiterp

Caterpillar has been involved in highwall mining since the purchase of Bucyrus in 2011. The Cat® HW300 is a continuation of the Superior Highwall Miner that was first sold in the USA in 1994. Currently, there are more than 80 machines supplied worldwide, and Caterpillar envisions increasing the population steadily in the coming years. The Cat highwall miner product group, based in Beckley, WV, has been involved in the sales of all miners to date. With the dealer model that Caterpillar is using, more people, dealers in particular, need to be trained on the application of highwall mining. A site investigation is a highwall specialist?s work, and Caterpillar assists dealers and customers in determining the technical feasibility of highwall mining on mine sites. With the ever-increasing amount of requests, it proved to be important that people without highwall mining expertise, yet who are familiar with mining, could perform a very quick analysis of a potential highwall mining site to determine at an early stage if it is worthwhile to invest the time and money of all parties?customer, dealer, and Caterpillar?in further follow-up. Therefore, Caterpillar would like to introduce the Cat HW300 QuickScan tool.

Jan 1, 2014

In this paper, three types of value-adding in the minerals industry are discussed: downstream processing, improving the efficiency of existing processing and increasing the knowledge base and expertise of the staff. It is shown that, while downstream processing seems to offer a good way of improving Australia's trade position, there are a number of impediments to such development, notably, limited access to the appropriate technology and overseas markets. Transport costs can also be a problem. To reverse the situation will require more positive policies by government. In the meantime, something can be done towards adding value by increasing the efficiency of existing processes. Examples are given, showing how it might be possible to make economies in reagent costs in the gold industry, how innovative technology has led to more complete processing of a tailings dump, how research might lead to an increase in the throughput in the production of synthetic rutile and how it is possible to leach selectively from gold/copper ores.

Jan 1, 1995

By Paul C. Miclea

With the growing urban population and the concern for traffic congestion and pollution (emissions control), public transportation is becoming more and more attractive to both city dwellers and managers. To gain access to the central area of the city, the sub- way remains the most viable alternative, despite its higher cost when compared to above ground or elevated transportation systems. There are relatively few regulations and criteria for subway ventilation, particularly when compared with mine ventilation. The main document that provides guidance and general recommendations for subway ventilation and environmental control is the Sub- way Environmental Design Handbook, published in 1976 (2nd edition) by the U.S. Department of Transportation, Office of Re- search and Development. Many of the subway systems in existence today have been designed and built with ventilation features adequate for normal train operation, but their design does not consider stringent criteria for such emergency conditions as a train fire in a tunnel. The National Fire Protection Association's Standard for Fixed Guideway Transit Systems known as NFPA 130 as well as the ASHRAE Handbook - HVAC Applications (1995) provide specific design and operation requirements for subway ventilation systems. Some of the existing, old subways are upgrading their ventilation systems to comply with the new regulations. The ability of a particular ventilation system design to provide adequate ventilation during normal and emergency conditions can be evaluated using computer modeling and simulation techniques. A train fire will cause a sudden change in the tunnel ventilation pattern by adding an unsteady and fast-growing source of heat. The hot air and gasses created by a fire will tend to flow uphill, possibly against the normal flow, producing a 'backlayering effect." To prevent this effect from happening, enough ventilation must be provided and the governing criterion to establish the required airflow is called 'Critical Velocity." Several software packages are available for special applications on tunnel and station ventilation as well as to model the spread of smoke and heat in case of a major tunnel fire, using Computational Fluid Dynamics. This paper presents the current issues in subway ventilation, as shared by the public transit community around the world, together with modern alternative design concepts vis-à-vis the more stringent emerging Fire-Life Safety criteria. Examples of recent studies and ventilation systems design are provided.

Jan 1, 1997

By C. M. Campbell

IN 1934 Newfoundland, after extravagant operation based on exaggerated ideas of what she had to work with, became bankrupt, ceased to be a self-governing Dominion, and passed into the hands of a Commission. Since the days of Dawson, Canadians have been taught that no country in the world is as rich as their own. This idea has become a religion; contrary views are heresy, and are suppressed even by technical organizations and government departments. Following the alleged habit of the ostrich, we have buried our heads in the sand and have refused to face the facts. This policy of "to have today and to hell with tomorrow" is now bearing fruit. After forty years of operation on the basis of unlimited natural wealth, with resulting over-expansion, wholesale depletion of capital assets, and huge borrowings, we are, now that our wealth has been shown to be very limited, face to face with the status of Newfoundland. Already, in this Province, commission government of bankrupt municipalities is not uncommon. The ostrich is referred to as the most foolish bird in the world. That is not the case-no ostrich ever hid his head in the sand. In the clear air of his home on the South African veldt, an area characterized by low bushes, he is a conspicuous object. When danger approaches, he lowers his head; matches his background, the bushes; and danger passes him by. This leaves the Canadian, with his head still in the sand, to fill the r61e cast for the ostrich. Fortunately, a few Canadians never did get their heads covered; others are getting them out far enough to see what is going on. Their comments are very much to the point. "Nowhere in the world," says Mr. Meighen, "has more harm been done to any country by an exaggeration of its resources and potentialities than has been done in Canada'.

Jan 1, 1941

By J W. Glatthaar, M Mavotoi

The occurrence of fluorine in the copper/gold concentrates produced by Ok Tedi Mining Limited has provided a series of challenges to metallurgists since 1988. Although fluorine is distributed throughout the gangue minerals contained within Ok Tedi ores, itsÆ presence in talc and phlogopite (naturally floating fluorosilicates) has proven to be the predominate sources of fluorine in the final concentrate. Initial treatment for the fluorosilicates consisted of the use of a carboxy-methyl cellulose depressant added to the flotation cleaners. This was superceded in 1998 with the installation of a fluorine reverse flotation process for the removal of naturally floating fluorosilicates from the final concentrate when the fluorine content of the final concentrate exceeds smelter-defined trigger points. The fluorine reverse process is similar to by-product molybdenite concentrate production in that sodium hydrosulfide is used to depress copper/gold flotation whilst allowing the fluorosilicates to float. The process was installed in two parallel modules (to match the existing grinding/flotation modules at Ok Tedi), each consisting of a closed rougher/cleaner circuit configuration. Both rougher and cleaner cells are Jameson Cells from MIM Process Technologies, with the selection based on both processing characteristics and available construction space. This paper discusses both the nature of fluorine in-, and its removal from-, Ok Tedi copper/gold concentrates.

Jan 1, 2003

By Richard C. Barth

Fourteen field plots were established at active coal mines in the Northern Great Plains. A wedge was cut into spoil and backfilled with soil; soil depth ranged from 0 to 152 cm over a linear distance of 15 m. Perennial grasses were planted in each plot, and production was measured from 1978 to 1981. Based on spoil traits and biomass response patterns, plots were grouped into four types. Spoil for Type I plots was near neutral, slightly saline, nonsodic, and clay loam in texture. Perennial grasses reached maximum production with approximately 50 cm of soil depth. Spoil for Type II plots was characterized as sodic and fine textured; soil-depth requirements averaged 83 cm for maximum production. Spoil for Type III plots was characterized as strongly acid, and production increased throughout the soil depth range tested. Spoil for Type IV plots was similar to soil in chemical and physical traits; there was no production response to soil depth. Soil depth requirements were also dependent upon precipitation and species. In general, soil-depth requirements decreased in dry years and with use of introduced species. An appendix contains data evaluations on an individual plot basis.

Jan 1, 1982

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By C. Holmes, T. Holmes

Engineered-in material handling problems are responsible for significant unrealized value in mineral processing plants. At the root, is a lack of awareness and understanding of bulk material handling science and how important it is, especially in early design stages. Mineral processes add value to mined raw feedstock through physical and chemical transformations in unit operations, but only if the material can flow through them. Essentially, each unit operation receives a unique feedstock and produces a unique product to be collected, transported, and fed into the next unit operation. Such material-handling systems can only be expected to achieve design throughput if the system equipment is designed to the materials’ characteristics, over their full range of conditions. This requires quantification of flow properties to support the necessary customized equipment designs. Too often, assumptions or “library values” of a material’s properties are used as the basis for flow modelling and conceptual, and sometimes even detailed, design. This is especially true for hazardous materials like uranium ore, for which the additional precautions, costs, and time necessary for safe handling are often used to rationalize postponing or even bypassing testing. The surprises that often transpire in the wake of insufficient material handling consideration can have acute and costly effects. Fortunately, there is a better way.

Jan 1, 2020

By B. L. Gibbs

The mining industry is constantly in a state of flux -boom or bust; mine openings and closings. Part of the reason is the nature of ore deposits -they are there or they are not. Once they are mined, they are reclaimed and the move is on to the next deposit. Risks are usually high, and payoffs can be great or not so great. Many factors go into making a property payoff, and mining companies are continually searching for ways to remain profitable as long as possible. Computers and the people who can make them work are one of the ways available to improve productivity and ensure this happens. Computers have been used in the mining industry for the last 30 years (and more in a few cases). During the past 10 years, the explosion of micro-computing has changed how many mining companies do their work.

Jan 1, 1993

By Thomas Varley

"The literature on flotation of oxidized ores except for patents (especially for reagents) is very sparse. The Bureau of Mines in 1936, published a circular on the subject, by Ralston and Allen. The treatment of oxides by flotation was then in its infancy, but several of the most important mining companies in the Western United States and Mexico are now operating flotation plants for treating oxidized ores. The purpose of this present circular is to review the progress made and bring the subject up to date. One of the writers of the 1916 report (Mr. Allen) has been associated with some of the most important mining companies who have put into practical operation the process of flotation of oxidized ores; among these companies are the Shhttuck Arizona Copper Co., Bisbee, Arizona (now the Shattuck Denn Co.) and the San Francisco Mines of Mexico, Ltd., San Francisco Del Oro, Chihuahua, Mexico. His experience and other sources of information have been freely drawn on in pre-paring this paper. Mr. Ralston, assistant chief metallurgist of the Bureau of Mines, contributed many valuable suggestions and criticisms.Sulphidizing Reagents for Oxidize Ores.The various reagents and methods that might possibly be used for sulphidizing were summarized by Ralston and Allen as follows:""Sulphidizing (1) by the use of hydrogen sulphide on either the dry or the wet crushed ore, (2) by the use of solutions of the various sulphides and sulpho-compounds of sodium, (3) by the use of solutions of the various sulphides and sulpho-compounds of calcium, (4) by the use of sulphur vapor, (5) by the use of a sulphureted oil, (6) with colloidal sulphur."

Jun 1, 1927

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By Richard Lusignea

A single boom roof bolting machine was outfitted with measurement and recording systems for detecting changes in machine parameters while drilling. The purpose of this instrumented bolter or "smart drill" is to detect changes in roof conditions from the machine parameters of penetration rate, thrust, rotation rate, torque, rejected light from rock cuttings, and vibration of the roof during drilling. The system was demonstrated underground in coal mine conditions and showed correlation between rock type and drilling parameters.

Jan 1, 1982

By A Huebner, A Noack

Companies all over the world are very sensitive concerning their IT and network security. In most network connected technical installations and machines however, network security is not taken into account to a significant extent: insecure protocols are run, unencrypted information is exchanged freely and even broadcasted wirelessly and networked machines are accessible via insecure file transfer protocol (FTP).What happens in case of malfunctions of such technical installations? Who is responsible? Who can be held liable in case of accidents? The first computer worm for automation systems (æSTUXNETÆ) (Symantec, 2010) was discovered during 2010.The paper is intended to create sensitivity among decision makers for potential security and resulting safety leaks and points out the current status quo in technical network security. It outlines best practices for secure networking and procedures for remote access and remote software updates on stationary equipment and mobile mining machinery. It describes how to ensure authentic and genuine configurations and software targets and how to ensure secure communication for autonomous and remote controlled equipment. For such equipment in particular, the following statement should apply: æThere is no safety without network securityÆ.

Sep 26, 2011