Search Documents

By Martin Dirks

Nowadays the sinter cooler often becomes the bottleneck of the sinter production, with outdated equipment leading to low productivity and high operation and maintenance costs. Furthermore valuable energy is simply destroyed in the cooler, which is not compatible anymore with a cost efficient and environmentally friendly sinter production. Paul Wurth has developed and improved two types of coolers, the annular cooler and the shaft cooler which offer flexible solutions to the specific situation of each client. The classic design of the annular cooler was completely revised and is now composed of a rigid ringframe construction as opposed to the traditional design with individual sintering cars, avoiding the typical problems of centering. Additional features of the PW annular cooler are the low air leakage rate and the increased effective cooling surface due to the removal of dead areas. This leads, in addition to the lower weight, to lower operating costs and a smaller space requirement. The shaft cooler stands out with an even smaller space requirement and a lower sinter outlet temperature because of a very long residence time of the sinter inside the shaft. Its development into a pure counter flow cooler aims at maximizing its energy efficiency, as it is designed as a system with a very low demand for cooling air, high air discharge temperatures and highly reduced dust emissions. For both cooler types flexible heat recovery solutions can be offered. These solutions include the supply of hot combustion air to the ignition hood burners and the sinter strand, the production of steam for the clients steam grid or the production of electric energy.

Aug 16, 2017

By Joan C. Biordi

A molecular beam-mass spectrometer-low pressure flat flame apparatus has been constructed for the purpose of examining the chemical microstructure of normal methane-oxygen-argon flames and those inhibited with Halon extinguishants. Details of construction and performance of this apparatus and of related flame temperature measurements are given. Particular attention is paid to the empirical characterization of the perturbation to the flame caused by the sampling probes. The composition profiles obtained for normal flames are compared to those of flames inhibited by CF3Br. In addition to the usual stable species (CH4, O2, CO, CO2, H2O, H2, and H2CO), the inhibitor, its products and intermediates associated with its reactions could be followed. In particular, hydrogen bromide, bromine atoms, hydrogen fluoride, and carbonyl fluoride were observed. The relatively rapid disappearance of inhibitor and early appearance of fluorinated reaction products suggest a short lifetime for the CF3 radical in this system. Observation of COF2 suggests that CF3Br is effective as an inhibitor, at least in part, by virtue of its interference with the oxygen containing species of the normal chain reaction. Profiles of the 17+ peak at low electron energy suggests that the hydroxyl radical may also be sampled, but the profiles obtained are not yet sufficiently accurate to determine the effect of inhibitor on this important flame radical.

Jan 1, 1973

By B McCarthy

Mining has been typified of late as a boom and bust, cyclical industry operating against a steady decline in the size and quality of mineral deposits. Decreasing deposit grades and increasing costs of traditional mining techniques, all in the face of another commodity downturn, are forcing mining companies more than ever before to seek out new and innovative ways to operate. New technologies are emerging to model, control and track resources through the mining value chain, to move material about mines more efficiently, and to identify and separate ore from gangue early in the extraction process.Discovering such technologies however is only the first challenge for mining companies. Actually implementing technological change successfully has proved to be an even bigger challenge. Like for many industries, fulfilling the promised benefits for the expense and timing envisioned, has not been easy when innovative technologies are introduced.Citing the author’s insights and experiences in a number of emerging technologies, this paper explores barriers to implementing technological change in the mining context. Key elements of a change management framework, first developed for implementing mine management systems, are described to give mining executives insight into how they and their organisations can succeed through technology-driven change.CITATION:McCarthy, B, 2016. Successfully implementing technology-driven change in the mining environment, in Proceedings International Mine Management Conference, pp 89-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By C Jenkins, J Jasper, Y Suryaputradinata, S Lozyk, M J. Hartmann

The primary objective of mining companies is to function as a profitable business by delivering products that fit customer requirements in a safe and sustainable manner. Optimum resource utilisation is a critical focus area to achieve this objective, and the long-term sustainable business performance of a mining company is determined by the extent to which this is achieved. Technology improvements and/or new technology development could improve resource utilisation. However, adding new projects to a Brownfield operation carries risk. Overall project schedules, tie-in schedules and safety risks normally receive adequate attention, but the introduction and integration of new technology to a Brownfield site also carries the significant risk of failure to achieve design performance (quality or throughput). This risk must be addressed via rigorous design phase risk assessments and piloting. Post commissioning, the effective metallurgical integration of any new technology/circuit/process plant into an existing process plant calls for critical assessment, through circuit performance testing, and optimisation to ensure alignment with design criteria. In addition, this approach provides clear focus areas for further optimisation of the new plant and additional opportunity for overall plant optimisation. Roy Hill recently navigated this process successfully, and this paper provides feedback on the journey that led to improved resource utilisation.

Nov 8, 2021

By Joe Pease

"The demand for minerals and metals is increasing. Head grades of ore bodies are dropping. Remaining ores are becoming finer grained, more complex, and more logistically challenging. Mineral processing – in particular comminution – already consumes a huge amount of energy. But in 20 years’ time, it will require about six times as much energy as today to meet the world’s mineral demand.Unless we do something different.As minerals professionals, it is our job to find that “something different”. The world is relying on us. Of course, we must look for new breakthrough technologies and techniques. We must find them, and we will find them – most likely in surprising areas.But what if we also already know how to make 30-50% improvements to efficiency? Just by using existing technologies, by applying modern analytical techniques, by custom designing our plants, by applying manufacturing principles, by breaking down our management silos between disciplines.The thing is, industry professionals already know this. Yet – in spite of a lot of intelligent people trying very hard – we just can’t seem to make it happen.This discussion considers why, despite our best efforts, we don’t get the best out of what we already have. Why we are wasting energy and money. Once we understand why, we can set about unlocking that value and improving industry productivity and energy efficiency. We will discuss the role that professionals and volunteer professional organisations like CMP and CEEC can play in catalysing the changes."

Jan 1, 2015

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965

By John R. Hawley

Ontario, one of the richest mining districts in the world, is a natural storehouse for much of the earth's fresh water supply. Covering over 344,000 square miles, the surface of this Canadian Province is dotted with 250,000 fresh water lakes and is laced with uncounted thousands of fresh water rivers and streams. The southern portion of the Province, for the most part, is flat or lazily rolling farmland. This is where most of the people in Ontario live. Although it is not a major mining area, southern Ontario does possess important deposits of salt, oil, gas and gypsum. Most of these deposits are being actively worked. Toronto, the capital city of Ontario, lies deep in the southern region. Here the climate is mild and the winters are short. The total annual precipitation consists of 27 inches of rain and 65 inches of snow. Most of the major mining companies that do business in Canada have made Toronto their Canadian headquarters. There are two reasons for this. The first, of course, is money. Toronto is the gathering place of many well- known financial institutions. The second is access. Toronto lies within a few hundred miles of some of the most spectacular mining enterprises that exist in the world.

Jan 1, 1973

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

Stillwater Mining Company has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The first use of a TBM was a 4 m (13 ft) diameter main beam unit at the Stillwater mine starting in 1988, where 6.4 km (4 mi) of tunnels were driven parallel to the J-M Reef orebody on four different levels. TBM?s were central to the development of the East Boulder Mine as two 4.6 m (15 ft) TBM?s drove two 5,639 m (18,500 ft) parallel tunnels to access the J-M Reef; one of these units is still in service driving a 2,591 m (8,500 ft) access West of the East Boulder mine for the Graham Creek project. For the Blitz Project, a 5.5 m (18 ft) diameter main beam unit will be utilized to drive a 6,858 m (22,500 ft) ventilation and rail haulage level East of the Stillwater mine. TBM?s have been preferred method for developing new mines and sections of the J-M reef as the geometry and geology of the Stillwater Complex allow for faster development compared to conventional methods.

Jan 1, 2012

By V. A. Nieberlein

The purpose of this investigation is to determine the reserves of columbium (niobium) minerals in Arkansas and to develop metallurgical methods for concentrating the minerals and extracting the metal. The columbium resources of central Arkansas were explored by drilling and trenching, and a number of samples were taken. On the basis of this exploration the known reserves of the metal were estimated to be over 78,000,000 pounds. The reserves could possibly be extended by additional exploration to 150,000,000 pounds.

Jan 1, 1954

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce risks of coal dust-fueled explosions. The goal of this NIOSH study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust (<75 µm diameter) in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity. Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing, and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle is operated at high fluid pressures to produce smaller droplets and move more air. These findings can be used to select sprays and design spray arrays to control airborne float dust over the entire longwall ventilated opening. INTRODUCTION Coal mining processes produce airborne dust that naturally deposits on the floor, roof, and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 microns in diameter, are deposited in return entries of coal mines and can be re-entrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; NIOSH, 2006). These particles are also those most likely to participate in coal dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (CFR, 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal dust-fueled explosions. Water sprays are both effective and widely accepted as a method for controlling underground coal mine dust. In fact, water sprays are considered to be the most economical and technically feasible means of reducing dust concentrations in underground coal mines (Courtney and Cheng, 1977; Barker and Humphreys, 1996). Sprays are used in several ways to control dust in mining processes: inhibiting dust formation, immobilizing dust to prevent it from becoming airborne, and capturing airborne dust (Cheng, 1973). Reductions in airborne dust concentrations have frequently been attributed to inertial impaction between water droplets and dust particles, forming larger agglomerates which then quickly precipitate out of the airstream (McPherson, 1993). Inertial impaction activity is generally accepted as the major capture mechanism for airborne particles larger than 0.5 µm in diameter. It is this mechanism that is evaluated in this study."

Jan 1, 2017

By A. Becker, C. Gauvreau, L. S. Collett

"A scale model was designed to simulate the airborne Barringer INPUT time domain electromagnetic system. The amplitude of the response to a vertical conductive dyke varies considerably with the conductor's thickness conductivity product (TCP). The response increases from a minimum detectable level at a TCP of about 2 mhos, rises to its maximum value at a dyke TCP of 15 mhos and then falls again so that conductors with a TCP exceeding 500 mhos would probably remain undetected. Measurements made with both standard receiver coil configurations (maximum or minimum coupled) indicate comparable effectiveness for both systems, either from the viewpoint of vertical conductor detection or from the viewpoint of discrimination against overburden anomalies."

Jan 1, 1972

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By Farnham. G. S.

It is difficult co know how to deal with this subject before a group having such mixed interests. The mining man is not coo concerned with the problems of alloy research. The engineer is more interested in properties of materials than how these properties can be achieved. The business man feels that scientific history and prognostication are not for him, predicting trends or possible developments in the economic field being a more than sufficient occupation. Yet the application of physical metallurgy research to industry is of importance to miner, engineer, and business man, for only through such application can the continuing existence of industries manufacturing or consuming metals be assured. History shows that hard work does not guarantee industrial survival. For instance, the Bessemer method of steel making superseded puddling operations; it, in its turn, has been largely displaced by open-hearth processing; later, steels made in electric-arc furnaces displaced open-hearth products in the quality field; and now, very specialized steels are being made in high-frequency rather than in arc furnaces. It is apparent then, if industry is co remain healthy, complacency must give way co imaginative planning, based on a thorough knowledge of production technique, a knowledge supplied by efficient research.

Jan 1, 1947

By Pedro Lilienfeld

The objective of this program was the development, design, and fabrication of six personal-sized completely self-contained dust monitors capable of real-time as well as time-averaged monitoring of the concentration of respirable particles in coal mines, in the range of 0.1 to 100 mg/m3. The operation of these monitors is based on light scattering and passive air sampling. The design stressed overall miniaturization, ruggedness, simplicity and versatility. These instruments incorporate a single-chip CMOS microprocessor to perform all signal processing, data display and storage, and timing functions. The overall dimensions of these devices are, approximately, 10 by 10 by 5 cm.

Jan 1, 1982

By DIEGO RAFAEL MONTEIRO DINIZ

Os processos de recebimento, armazenamento e distribuição de combustíveis em grandes empresas mineradoras necessitam de um controle robusto e eficaz de todas as operações, uma vez que representam elevado custo por tonelada de minério produzida e expedida. Para tanto, a automatização dos processos que envolvem combustíveis é necessária, capaz de promover redução de custos, aumento de produtividade, confiabilidade e precisão nos dados e melhorias nas condições de trabalho na gestão e operação em combustíveis. Foi aplicada uma análise descritiva de um estudo de caso de um projeto de automação para esta finalidade implantado na empresa VALE S/A. Foi feita uma avaliação sistemática dos recursos, equipamentos e tecnologias necessárias a completa automação e integração dos processos que envolvem combustíveis e os ganhos alcançados após a implantação.

Oct 30, 2017

By C. M. Iheagwara

An overview of the scope and ramifications of scrap recycling in the Nigerian metallurgical industries has been presented in this paper. The modern state-of-the-art processing techniques and the operational strategies employed in the recycling plants are discussed. Optimization techniques for cost effective recycling operations are highlighted. As new units within existing metallurgical plants and new metal working plants approach commercial operations, expansion of existing recycling plants and the emergence of new ones have been showing to hold the key to their profitability from the raw material standpoint. The present economic predicament of the entire industrial sub-sector, lack of sufficient foreign exchange to procure new machineries and the emergence of a maintenance culture have triggered a phenomenal increase in the number of spin-off industries which depend on metal recycling activities. This, it is argued, widens the horizon for scrap processing/recycling.

Jan 1, 1992

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By M. S. Enders

The McDonald deposit is a volcanic-hosted epithermal gold resource that is estimated to contain 251,000 kg of gold in 375 Mt of ore at an average grade of 0.7 g/t gold. Phelps Dodge exploration geologists, working for the Seven-Up Pete Joint Venture, discovered the deposit in 1989. By the end of 1992, 494 drill holes for over 113,000 m of drilling, bulk sampling, soil geochemistry, geophysics, metallurgical testing, engineering, and environmental studies had been completed to support feasibility studies. The discovery of McDonald required vision, persistence, and commitment of everyone from the geologist on the drill rig to the senior management of the company.

Jan 1, 1995

By Carleton Ellis

(Presented at a meeting of the New York Local Section of the Institute, Apr. 12, 1912.) I. INTRODUCTION. THE problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific stand-point, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by way of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " ?flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of combustion as they occur in ordinary flames. All hot surfaces have an accelerating influence upon chemical changes in gaseous systems. If, at any temperature, a gaseous system, A, tends to pass over into another system, B, contact with a solid at the same temperature will accelerate the process. To take a very simple example, if a mixture of hydrogen and oxygen in their combining proportions (electrolytic gas) were maintained in an inclosure with smooth glass walls at a temperature of, say, 450° C., there would certainly be a tendency to form steam, but the rate of change would be negligibly small. If, however, there were brought into the system some porous solid material at the same temperature, so that a large surface was exposed to the gases, the rate of change would at once be rapidly accelerated in the layer of gas immediately in contact with the hot surface. Steam, the product, would diffuse outward from the surface, and the supplies of hydrogen and oxygen at the surface would be renewed by diffusion inward. Thus combustion would proceed heterogene-

Sep 1, 1912