Search Documents

By David D. Eyer

In today's world coal market, coal quality is becoming increasingly important. Often the coal quality parameters are one of the crucial considerations in the development of a coal mine. Because of the user's tighter specifications and because of strict environmental regulations, coal producers are being called on to predict with increasing accuracy, not only the quality of their product but also the variability of that quality. This area of reserve evaluation is naturally receiving a great deal of scrutiny. Consolidation Coal Company has developed reliable and sophisticated methods for predicting coal quality, but the company's efforts continue to search for even better techniques. The following is a step-wise summary of The methods currently used by consolidation coal company, with A recent project used as an example. Two of the newer, and as yet experimental techniques will be briefly discussed.

Jan 1, 1980

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By J Janus, J Krawczyk

Local accumulation of methane in workings of a longwall is one of the most common causes of mining accidents. This gas has many sources: it may leak from goaf through permeable sealings, or through gaps between roof support sections. This stream is then mixed with ventilation air. In the case of auxiliary ventilation ducts, or free jet fans, we have to consider the propagation of a clean air stream in areas with an air-methane mixture. Therefore, modelling the mixing process of methane with ventilation air is important for determining the hazardous areas and thus to ensure safety. Computational fluid dynamics (CFD), specifically the finite volume method, provides tools for such modelling. However, this method requires validation. For this purpose, we have compared measurements with simulations for selected test cases having sufficient similarity to the present problems. In typical methane explosion hazard areas, such as a longwall, it is difficult to make measurements sufficiently to confirm credibility of 3D CFD simulations. As a relevant alternative, an injector methane drainage station placed in an underground gallery has been selected. The stream of drained goaf methane is entrained by compressed air powered injectors and then mixed with ventilation air. Research in this area does not interfere with mining operations, it can be performed safely in a repeatable way. Flow within the site has many similarities to conditions in mine drifts of the longwall area. Comparative research of measuring the methane concentration distribution in the mine drift downstream injector station, with simulations of propagation of the methane stream, was carried out. For measuring the methane concentration distribution in the mine drift a multipoint measurement velocity system developed at the Strata Mechanics Research Institute was used. For the simulation a finite volume method for turbulent flow of gas mixtures was applied. Preliminary results of comparison are shown as graphs and tables.CITATION:Janus, J and Krawczyk, J, 2013. An analysis of the mixing of air and methane in the stream produced by the mine injector station - Presenting preliminary results of measurements and modelling, in Proceedings The Australian Mine Ventilation Conference , pp 49-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Norma Golumbic

The primary purpose of the Bergius (hydrogenation of coal) and Fischer-Tropsch (hydrogenation of carbon monoxide) processes is the production of synthetic liquid fuels. This objective is of importance in insuring an adequate supply of motor fuels and lubricating oils in the United States. In the urgency of the basic research and process development work on synthetic liquid fuels, the possibilities for the production of synthetic chemicals inherent in these processes have hitherto received little attention in this country. However, the by-products, as well as the primary products, from the Bergius and Fischer-Tropsch processes are rich source materials for organic chemicals. The overhead oil from liquid-phase hydrogenation of coal, for example, contains benzene, toluene, xylene, cyclohexane, methylcyclohexane, aromatic solvents, about 20 percent tar acids (largely phenol, cresols, and xylenols), and 3 percent nitrogen bases. Wax, alcohols, and acids are by--products of the Fischer-Tropsch synthesis. In addition, techniques have been developed which make possible the production of aliphatic hydrocarbons, alcohols, acids, aldehydes, and other oxygenated organic compounds. These chemicals are more valuable on a unit basis than gasoline. Because of continued rapid expansion of the plastic, resin, lacquer, and solvent industries, larger amounts of many of these chemicals will be needed in the near future.

Jan 1, 1949

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1952

By V. H. Forsythe

Mr. Chairman, members of SME, and guests It is indeed a pleasure to have the opportunity to appear before this group. The topic of this paper is, "Current Trends in Related Industries and Their Influence on Electric Shovel Design and Size". Before getting into the major items, it is well to point out that this text will deal with loading shovels primarily, since their application is almost universal in major open pit mining operations throughout the world. Related industries influence our design in many ways. For the sake of simplicity, these industries will be broken down into two major categories. The first category to be discussed will include industries that will indirectly influence design and size, while the second category will include industries whose products can directly be incorporated by the engineer in the design of shovels.

Jan 1, 1964

By N. Rouse

Underground raises and slots are a vital part of underground blasting operations. Raises and slots are vertical shafts or openings used for ventilation, ore passes, or creating voids in stopes. In the author’s experience, raise and slot designs can vary significantly from operation to operation or even within a single operation, sometimes for reasons unknown. The results of the various designs can differ depending on drilling accuracy, geology, and the explosives used in the design. The purpose of this paper is to summarize the recommendations found in published literature on raise and slot design in one document, while incorporating some of the author’s own experience with optimizing raise and slot designs in underground operations. Some inspiration is also included from burn round designs; small versions of raises drilled horizontally in development blasting rounds. This document includes discussion points on drillhole diameter and depth, pattern design and relief requirements, explosive types and loading recommendations, and timing. Ultimately, this document can be useful to those looking to design a raise or slot blast for the first time or for those looking to improve on the results from the raise and slot blasts used at their operations.

Jan 1, 2024

By Roger G. Long

This final report reviews installation, maintenance and inspection of mine pager telephone installations. A Technical Handbook was developed and distributed. Certain commercial telephone test equipment was modified and a tone source and switching circuit were developed for use in the testing of mine pager phone systems. Descriptions are included of the modifications to a commercial test set and of a tone source/ switching unit.

Jan 1, 1975

By J Whittle

This paper describes what is involved in carrying out a comprehensive optimisation of a long-term operating schedule for a mining complex. It details the data that must be assembled and discusses the different approaches to optimisation and what limitations they put on the variables and constraints that can be handled.CITATION:Whittle, J, 2014. Not for the faint-hearted, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By B Dodd

This paper details how the Australian Securities and Investments Commission (ASIC), as a disclosure and conduct regulator, approaches regulation of continuous disclosure, capital raising and control transactions in the mining and resources sector, and the reasons for the approach. In examining this topic the paper considers the Joint Ore Reserves Committee (JORC) Code (JORC, 2004), the VALMIN Code (VALMIN Committee, 2005), the relevant ASX Listing Rules and the relevant provisions of the Corporations Act 2001 (Corporations Act). This paper discusses ASICÆs approach to expert reports and disclosure with reference to Regulatory Guides 111 Content of expert reports and 170 Prospective financial information.CITATION:Dodd, B, 2012. Issues in capital raisings and disclosure, in Proceedings International Mine Management 2012, pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By GEORGE S. POPE

This bulletin is a revision of Bulletin 63 and is published by the Bureau of Mines in order that purchasers of coal for Government, State, municipal, or private use may be informed regarding advances or refinements in sampling coal deliveries and preparing specifications for the purchase of coal. The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form, but the same in principle, has been gradually adopted by other departments until, at present, of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publioations a listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples representing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the specification method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly representative of the commercial product delivered in wagons, railroad cars, or ships. Therefore the method of taking and preparing samples for shipment to the laboratory has been given fully as much care as the making of the analyses and tests, and a general plan of collecting samples fairly representative of the delivered coal has been evolved through various modifications and improvements based on experience and increased knowledge of the physical and chemical characteristics of the various coals that are purchased by the Government. The method that is in general use by the Government is described in the following pages. In connection with studies of the coal deposits of the country, of the best methods of preventing waste in mining, and of increasing efficiency in the utilization of coal belonging to or for the use of the Government, geologists and engineers of the United States Geological Survey and of the Bureau of Mines have visited more than 2,500 coal mines scattered through all of the coal-producing States and Territories. From each mine 2 to 8 or more samples were taken, the number depending upon the size of the mine and its output. The analyses and descriptions of the samples collected up to the end of the fiscal year 1913 are published in Bureau of Mines bulletins 22 a and 85,b and those of samples collected in the fiscal years 1914 and 1915 are presented in a bulletin that will soon be published by the bureau. A study of the analyses of these samples and of the samples taken from cars shipped from a number of the same mines shows that the mine samples are as a rule of higher grade than the average commercial shipments, particularly with respect to containing a lower percentage of ash and having a correspondingly higher heating value. This difference is due to the fact that the Government inspector, proceeding on the basis of what can be done by a good miner, usually removes more of the partings of bone, slate, and other extraneous matter from his mine samples than the average miner does in ordinary practice, the aim of the miner being to get the maximum number of tons past the tipple inspection, as his earnings are based on his output. The average miner, therefore, does not always take as much care as he might in rejecting the impurities. The difference may be caused, too, by the presence of pieces of the mine roof and floor in commercial shipments. The Government inspector can readily

Jan 1, 1916

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By K. J. Ladwig

The Bureau of Mines conducted a field investigation of the water quality in inundated underground coal mines in the Northern Anthracite Field, eastern Pennsylvania. Water samples were collected at multiple depths from nine abandoned mine shafts in the Wyoming Basin, ranging from 68 to 650 m (223 to 2,132 ft) in depth and intersecting as many as seven mined seams in a single shaft. The shafts were also monitored for fluid resistivity, fluid temperature, Eh, and pH using downhole instrumentation. The monitoring program showed that the formerly highly acidic mine water is now slightly alkaline. Sulfate concentrations decreased as much as 74 pct in the flooded workings and 54 pct at a mine water discharge from values reported in 1964 and 1968, respectively. These data are consistent with the inhibition of pyrite oxidation and gradual flushing of oxidation products in flooded mine environments. The monitoring program also revealed significant vertical stratification in water quality in five of the nine shafts, each characterized by two easily recognizable zones. The transitions between zones were sharp, marked by rapid changes in Eh, pH, and ionic composition, the upper zones being less contaminated than the lower zones. The development of stratification appears to be a function of shallow localized flow conditions, arising primarily from the relative positions of mine openings and structural features of the coalbeds.

Jan 1, 1984

By T A. J Hopper, S Mukkisa, K-O Ott, D Palmer

RIG Technologies has developed new technology that can successfully acquire high quality natural gamma ray (GR) and hole deviations, downhole while drilling, on reverse circulation drills. This technology survives the hostile downhole environment with shocks of between 400–2500 g for 7– 10 days at a time. The Logging While Drilling (LWD) service eliminates the need to run in-rod surveys, either by the driller or by wireline trucks and crews. This time saving is in the middle of the drilling process, thus enabling drills to keep drilling and increase their productivity. Additional to the natural GR and directional survey, the downhole tool is equipped with sensors to measure the downhole dynamic response of the drilling system providing insights into rock hardness, density and potentially clay types. These parameters have never been acquired behind the hammer before and coupled with surface measurements from the drills themselves, form a rich data set for trainable machine learning algorithms shortening the time to receive advanced geophysical answer products from sometimes months, to live feeds directly from drills (Hopper, 2019). Alive, high speed, two-way data link between surface data acquisition systems and downhole geophysics tools has been established and incorporates calibrated surface measurements of dynamic forces directly on the drill string to match up with those measured downhole. Receiving live streams of natural GR and hole deviation surveys as the drill is drilling allows true remote decisionmaking with live data available anywhere in the world. The combined data from surface and downhole dynamics builds a data set that could begin to enable true optimisation of autonomous drilling processes.

Nov 8, 2021

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William C. McCulloch

INTRODUCTION The particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 25,400,000 tons of bituminous coal were cleaned by air machines during 1965. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 19 16, by the Sutton, Steele and Steele Co, Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., seven other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine. 2. Arms "Concentrator," oscillating table. 3. Hey1 and Patterson oscillating table. 4. "Stump Air-Flow," pulsating air jig. 5. "Super Airflow," pulsating air jig. 6. Ridge air jig. 7. Phillip air jig. While not all coals can be beneficiated by air washing, the air washing of coals that are easy to clean can be readily proved advantageous. Of all the preparation methods, pneumatic cleaning is the most acceptable from the standpoint of delivered Btu cost. This is based on the premise that a percent of moisture is just as detrimental as a percent of ash. The principle of dry concentration has never been determined with scientific accuracy. To the present time the study has been more of an art than a science. It is possible to forecast the results of wet concentration from a study of the washability characteristics of the raw coal but only after applying rule-of-thumb methods of interpretation to the specific gravity and size distribution can it be ascertained that the raw coal is amenable to dry concentration. Air as a separating medium dates back to biblical times as exemplified in the winnowing of chaff from the grain. However, the same application of air to coal serves merely to blow the dust away and size the remaining particles. Pulsating air was the solution to the problem and largely eliminated the necessity for close screen sizing which was required on early separators. Because of the low density of air, a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. Also, the

Jan 1, 1968

By W. H. Pomroy

This report describes research by the U.S. Bureau of Mines to design and in-mine test a rapid response pneumatic fire detection system for multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. The Bureau's prototype system is described, with emphasis on design features that counter commonly experienced and/or perceived operating problems with pneumatic detection systems. Finally, the results of a 3-year in-mine performance evaluation of the prototype system are discussed.

Jan 1, 1990

By H Arvidson, V Chamberlain, J Joughin, N Pollock, F Cessford, T Flitton, T Rowl

Environmental, social and governance issues (ESG) have become a defining feature in the marketplace to differentiate preferred investments. With the sustainability commitment and reporting landscape anticipated to evolve exponentially, it is now imperative to rapidly develop the approach taken by mineral companies to adequately identify and address ESG risks and opportunities in the reporting of Mineral Resource and Mineral Reserve (MRMR). MRMR cannot be effectively reported as technically and financially assured and realistically executable, if ESG is not integrated into the strategy, business model, input assumptions and process that defines and drives robust MRMR public reporting. Regulatory reporting codes across the globe are presently in various stages of being updated and modified to ensure ESG factors are appropriately covered as a key part of diligent and transparent disclosure. Security exchanges are making it clear that companies must not omit ESG risks from reports to investors. This paper discusses associated challenges for MRMR reporting and suggests avenues for improvement. Key themes include: the importance of procedure rather than prescription and checklists; how ESG criteria impact Modifying Factors and determination of Reasonable Prospects for Economic Extraction (RPEE); the need for financial models to account for material ESG commitments; the uniqueness of each mineral asset; the need for education, upskilling and accreditation of both ESG experts about MRMR reporting and equally Competent Persons in ESG matters; and the need for clear and balanced reports that meet the needs of end users. (RPEE is adopted here for simplicity and consistency, recognising that some reporting codes still include ‘Eventual’ in the term (ie RPEEE). Whilst RPEE and RPEEE are subtly different the intent is to point to the process of assessing ESG factors in determining reasonable prospects.) The principles of transparency, materiality and competence remain paramount when considering the impact of ESG matters on MRMR reporting, and this necessitates an inclusive, cohesive, and integrated approach to assessing ESG issues to ensure the necessary expertise and diligence is applied.

May 24, 2023