Search Documents

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By Linney, Robert J.

REPUBLIC Steel Corporation's iron-ore properties in the Adirondacks consist of mines, mills, and sintering plants in the Mineville and Port Henry area and at Lyon Mountain. This article will deal with the properties in the vicinity of Mineville and Port Henry. In 1938, when Republic leased the Mineville- Port Henry operations from the Witherbee Sherman Corp., these properties had just come through some hard depression years. As a result, the mine development program was far behind schedule; most of the equipment needed replacement; and above all, the entire system of mining had to be completely changed to reduce operating costs. The concentrator had been in operation for many years; the process was dry and dusty. Machinery and equipment were either badly worn or entirely obsolete. The sintering plant, also long in operation, was badly in need of repairs.

Jan 1, 1943

By F. B. Kuhnow

When performing blasting operations in open pit settings, energy is released and transmitted through the geology. Some negative effects can have significant impacts on mining operations and adversely affect mine production. This technical paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. The paper includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blastinduced ground motion. Based on the results, a set of criteria is provided to implement in current and future mining operations that involve blasting near underground concrete structures. A set of techniques on how to improve vibration levels for safe operations is also presented. Knowledge of particle velocity and wave propagation for site-specific circumstances to determine a safe level of vibration is recommended. Emphasis is placed on making use of electronic detonators and early delay detonators to achieve successful levels of vibration. A dynamic analysis is necessary to determine if vibration from blasting can damage the concrete shaft structure. When reinforced concrete structures are subject to blast loading, both concrete and steel are subject to very high strain rates. As opposed to static loads, when subject to high strain rate loads these materials increase their strength significantly. In fact, they increase by more than 50% for reinforcing steel, by more than 100% for concrete in compression, and by more than 600% for concrete in tension. This finding is of significant importance in mining operations because it allows an increase in flexural capacity of individual members as a result of high strain rates. Therefore, an elevated ground vibration (PPV) or particle velocity is permissible when blasting takes place near concrete structures.

Jan 1, 2014

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By W. Missildine, J. K. Hrica, I. Benbourenane, T. J. Orr, J. L. Bellanca

Each year, haul truck accidents account for a large portion of mining injuries and fatalities. To better understand why these accidents continue to occur, researchers from the National Institute for Occupational Safety and Health (NIOSH) utilized a cognitive task analysis methodology to identify the user requirements of surface haul truck operators and assess differences in perceptions between operators, managers, health and safety professionals, trainers, and maintenance personnel. Additionally, researchers used the critical decision method to focus on better understanding the cognitive demands, decision-making, and problem solving during nonroutine incidents. The preliminary results of this study identify and explore themes within the broad categories of hazards, skills & expertise, and training and provide detailed accounts of nonroutine incidents such as near-misses, loss of control, and collisions. These accounts reveal insights into operator decision making and event progressions that can then be used to build more realistic training scenarios and address hidden hazards and root causes of these incidents. These results, along with potential solutions offered by study participants, can inform future research and help identify creative interventions that can be used by mine operators to address haul truck safety issues

Mar 2, 2022

By Z. G. Li

The large-scale vibrating screen has been applied widely in coal industry and other industrial areas as a kind of important device. As vibration mechanical device, it works very hardly and works in very bad environment so that the structure of screen is damaged easily. Therefore, it is very important that how to detect the fault of structure as early as possible to make the repair schedule reasonably and economically and to avoid the body hurt and device damage. As a kind of important structure of vibrating screen, the lower crossbeam is the main carrying structure and it is easily damaged, so it is regarded as a researched object in this thesis and it is tested under the load in the laboratory. Based on the test, acoustic emission wave signals can be got-ten by modern acoustic emission testing technique. Then, the ?wavelet packet - energy? from the characteristics of acquiring signals is used as neural network input vector. In the BP network structure design, the design of a hidden layer with variable number of BP network is established. Based on the error by contrast, the best nerve number can be identified in the hidden layer. Through integrated analysis, using Levenberg-Marquard BP study algorithm, network-training errors are relatively small, the acoustic emission signal is used in BP neural network as a pattern of recognition. In Matlab6.5, neural network model identification is created and taking advantage of nonlinearity and the ability of learning and memory of Neural Network, this model is fixed by training structure of network with training samples. The work presented shows that acoustical emission signal processing and research on early fatigue fault diagnosis based on the wavelet and the neural network is viable.

Jan 1, 2014

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

During harsh weather conditions, the presence of fog, dust in the environment degrades the image’s quality, which affects the visibility of drivers of heavy earth-moving machinery in opencast mines. Due to low visibility, mining operations cannot be carried out as drivers are easily prone to accidents. This paper proposes a technique that includes developing a vision enhancement system called perceptive driving assistant system for increasing visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery at opencast mines during harsh weather conditions to overcome the problem. The system consists of high-quality Internet Protocol cameras and thermal cameras for real-time image processing and other well-defined devices, which is quite capable of enhancing the visibility of the image, outlining edges of the road, and detecting obstacles present on the path of operators for smooth driving and reducing threat of accidents. A high-speed graphical processing unit has been used for quality-performance parallel computing, which is well suited for real-time operations to empower fast real-time operations. The calculated frame per second (fps) of image enhancement, object detection, and edge detection is 17.91, 15.91, and 25.09 fps, respectively. The actual frame rate is 26.07 fps, and after applying the algorithm, the final frame rate is 19.65 fps. The calculated accuracy of the object detection model is 81.23%. Field trials indicate that the developed system has performed adequately during foggy weather.

Sep 21, 2022

By D. Bernard

Over the last decades, the wrought aluminum casting industry has made significant progress with regards to process consistency by the introduction of new technologies in the field of liquid metal processing and casting. These technologies, combined with the application of best practices, have led to increases in productivity as well as better process performances and product quality. The competition in the addedvalue aluminum products (by opposition to P1020 production) is, however, very strong and involves players that did not hold a major role five years ago but who are now exerting a strong competitive pressure on our industry even sometimes from far abroad. There are still technical and technological challenges remaining in the different areas of aluminum casting production, amongst which metal pre-treatment, furnace operations, in-line treatment and casting hold a predominant influence. The comprehension of the contribution of each individual process step to the entire process chain is a key element and must be considered in future process optimisations. This paper presents the technological position of the casting industry and tries to highlight areas where further progress can be made.

Jan 1, 2006

By Richard L. Fowler

Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the beam coverage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve a completely self-contained shuttle car system which responds to the existing mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to evaluate various guidance techniques during the feasibility study. Subsequent simulation runs were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing was performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated the predicted performance capability during underground face haulage tests. Dust did not impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance. Closed loop steering control with manual override is recommended for the lateral guidance system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.

Jan 1, 1973

By G. C. RIDDELL

THE metallurgist, chemist, and physicist are blazing trails that lead far afield. Pushing on into an "Alloy Age" they see a non-ferrous era over- taking iron and steel. Delving into the nature of the physical world, they break down a supposedly indivisible element, hydrogen. Not content with terrestrial problems, they peer back along the cosmic ray into iaterstellar space, glimpsing forces that are, apparently, still busy with the task of atom-making. Mastering and organizing the material and physical, they advance steadily toward that borderland of science where the concept of matter itself seems abandoned, and force is the substance left.

Jan 1, 1930

By S. Kariyawasam, R. McNealy

Pipelines are subject to multiple threats often requiring quantification of pipeline risk and engineering evaluation of in-line inspection and other data to effect discovery of conditions defined by the regulation. Public concern and pressure from regulatory bodies are accelerating the need for pipeline operators to formalize and intensify their approach to integrity management. Most operators need a phased approach to progressively adopt the most relevant and needed assessments. The organized and relevant assessment steps need to be introduced according to data available and maturity of the integrity management program. Each refinement to the quantification offers distinct advantages to the user. In this paper, the progressive integrity assessment solutions using quantitative methods are presented. Methodologies for engineering evaluation of integrity in-line inspection data for immediate and future integrity are summarized. Corrosion is used as an example, but the approach is applicable to any time-dependent defect based hazard. Strategies for pipeline integrity management are discussed.

Jan 1, 2005

By P .. R. Ammann

A two-stage pyrometallurgical process has been developed for the recovery of copper (and other non-ferrous metals) from copper smelter slags. All types of slags, including highly oxidized, converter-type slags, are cleaned in an electric furnace which employs mechanical mixers to promote magnetite reduction and copper extraction at high rates. In a 10-ton pilot furnace, it has been demonstrated that slags can be cleaned to 0.2-0.3 per cent copper with economically acceptable usage of raw materials and energy; copper is recovered as a high-grade matte. Pilot plant data have been scaled up to a commercial furnace and engineering designs have been made for a furnace to treat 60 tons per hour of slag from a Noranda Reactor and the associated converters. Plans are being formulated for the construction of a prototype slag cleaning furnace.

Jan 1, 1976

By R. S. Douglas

THE Granby Consolidated Mining, Smelting and Power Company, Limited, is engaged in the mining and concentrating of copper ores, and, incidentally, in the mining of coal and the production of electric power. The Company has been engaged in these various operations both on the mainland of British Columbia and on Vancouver island for the past forty-five years. This paper will attempt to cover their present operations in the Similkameen mining district of southern interior British Columbia. GENERAL CHARACTER OF THE DISTRICT The Interior Plateau in southern British Columbia ranges in elevation from 3,000 feet to 6,000 feet. In the vicinity of Princet0n, a depression in the Plateau forms a well defined basin which is floored with a series of nearly flat-lying Tertiary sediments containing some workable seams of lignite. From this basin, the upland surface rises gradually t0ward the south, from an elevation of 2,000 feet at Princet0n to 4,000 feet at Copper mountain, and 6,000 feet in the upper parts of the Similkameen basin, where it merges into the rugged and diversified t0pography of the Cascade system, with glacier inhabited peaks rising to over 9,000 feet. The valleys of Similkameen river and its tributaries are wide, having flaring sides and gentle slopes, and are separated one from another by subdued rounded spurs, of which Copper mountain is typical. The drainage of this district is taken care of by Similkameen river and its larger tributaries, such as Pasayten river, and Wolfe, Friday, and Whipsaw creeks. The name Copper mountain is applied to a gently arched, nearly flat-topped spur between the deep valley of Similkameen river to the west and the shallower valley of Wolfe creek tO the east. The mountain is appro-priately named from the number of copper deposits occurring on its sides and summit, some of which have been developed int0 an important producer, known as the Copper Mountain mine.

Jan 1, 1943

By Salustio s. Guzman

The standard .free energies of formation of tin chlorides were estimated with reviewed and estimated basic thermodynamic data, and measured reversible potentials for the disproportionation of tin dichloride into metallic tin and tin tetrachloride. Values for cºp, Sº, Hº?-Hº 298, -(Gº - Hº298) /T,.Hºf, Gºf, and log Kp are given in tabular form, these estimations are compared with estimations reported in the literature.

Jan 1, 1985

By S. Davis

It has been accepted almost as dogma that sampling contributes most of the error to fluctuations in gold fire assays. Differences in assay results on pulp material from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" or relatively coarse gold particles. It is true that if coarse gold particles are present they contribute to substantial sampling fluctuations, but while the process of sampling is probably the major source, the analytical process cannot -be completely ignored as a possible contributor to erratic assay results. In order to maintain a stable assay process, the analytic part of the system must be kept in control as well as the sampling and preparation part. One way of monitoring the performance of the analytic system is to systematically assay standard material whose sampling characteristics are carefully controlled. Gold assay standards are not prepared nor can they be prepared to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for preparation (which includes both the processes of comminution and splitting) followed by fire assay, to make inferences only about the fire assay process. Because most gold ores are very heterogeneous, sampling errors would in most cases completely mask the contribution of the analytical errors. Assay standard material is prepared only to assess the accuracy and variability in the fire assay process.

Jan 1, 1995

By Robert J. Tuchman

This report presents the origins of the Bureau of Mines and the evolution of the Pittsburgh Research Center from its inception to its present form. Areas of major research emphasis over the years, as well as administrative reorganizations, are discussed.

Jan 1, 1998

By Thomas E. Shumka

ASTM E2905 describes a two-part standard for electromagnetic methods for preparation and examination of ring gear teeth in the mining sector for SAG and Ball Mill ring gear drives, including pinions? particularly on the addendum, dedendum, and root areas. This practice addresses the need to detect surface breaking flaws electronically and to have the ability to accurately size any surface breaking cracks found on cast and forged SAG and ball mill ring gear and pinion teeth faster and more effectively than other methods. Eddy-current surface arrays are seeing increasing use throughout the industry for the detection of surface breaking flaws in conducting materials. Example applications include examinations of pipelines, bridges, engines, aerospace structures, and any conducting material for surface breaking flaws including cracks. In addition, model-based methods are being used to size cracks accurately found in the addendum, dedendum, and the root of SAG and ball mill girth gear teeth. As visual interpretation of a surface breaking discontinuity on gear teeth is the normal analysis, the colors and 3D images that are provided with this technique, help with visualization and therefore are absolutely invaluable in such circumstances. This practice will help to standardize the use of this nondestructive testing approach.

May 1, 2013

By D. R. Tweeton

The U.S. Bureau of Mines has developed tomographic computer programs for geophysical applications and is distributing them as part of a Bureau plan to facilitate the transfer of technology to potential users. These programs were developed for predicting and monitoring the flow pattern of leach solution during in situ mining. The Bureau has also applied them to assessing high-wall blast damage and examining the integrity of mine-related geological structures. This report describes the curved ray program BOMCMTR (Bureau of Mines curved ray tomographic reconstruction), tells how to run it, and gives examples with synthetic and field data. BOMCRATR provides optional mathematical constraints to counteract the nonuniqueness of tomographic reconstructions with crosshole data. These constraints include limiting the maximum and minimum velocities, fixing the velocity at any point to any value, and establishing layers in which velocity does not vary with horizontal position. The user can test for nonuniqueness by varying the initial velocity pattern, The program can perform either curved or straight ray analysis. Ray paths are calculated analytically in triangular pixels, which is faster than incremental numerical approximations,

Jan 1, 2010

By T. Holmes, S. Davison

"The Special Standard Surge bin at Agrium’s Vanscoy Potash Operations (VPO) has been plagued with flow problems and wear, and corrosion issues for it’s entire working life. Investigation showed that the carbon steel construction, bin geometry, and resultant funnel-flow pattern were directly responsible for production losses and disproportionate maintenance and capital costs. Potash enters this bin at between 140°C and 165°C, but the stagnant potash outside the active flow channel was much cooler, allowing moisture to migrate toward the outer regions, which caused corrosion of the walls and reduced live capacity as the potash in this area hardened and built up on the walls over time.A 2013 inspection revealed holes and paper-thin areas in the lower cylinder wall sections and in the conical hopper. The only thing preventing major leaks and even a potentially catastrophic failure was the buildup of stagnant hardened product on the cone walls. It was concluded that the cone had reached the end of its life and required replacement. VPO’s original plan was to replace the cone in kind and repair the cylinder as necessary; however, a failure-mode and bin-performance investigation combined with a lifecycle- cost analysis indicated it would be better to redesign the hopper.For success in retrofit projects, it is essential at the design stage to consider the bulk solid flow properties and the operating environment involved. Because education in this area is not offered at a university level, engineers often do not fully appreciate the effects of the flow properties of bulk solids on bulk material handling equipment.Jenike & Johanson conducted flow properties tests on samples of potash and using the data, redesigned the bin and the feeder. After the modifications, VPO’s surge bin provides safer, more reliable operation with a much longer predicted working life. Using this retrofit as an example, we aim to provide a general understanding of bulk solids flow theory and highlight the importance of customizing the design to the appropriate flow properties in the cost effectiveness, reliability, and safety of a bulk material handling system."

Jan 1, 2016