Search Documents

By R. Chowdhury

The relevance of reliability studies for deep foundations is considered in this paper with special reference to pile foundations. Attention is drawn to uncertainties related to applied loads, the load-carrying capacity and the safety margin of a pile foundation. The essential steps in a reliability study are outlined. An essential goal of any study is the determination of the Reliability Index or Safety Index under different conditions of loading and operation. Calculations concerning probability of failure or success require an assumption to be made concerning the probability distribution of the safety margin. The significance of this and other assumptions should be clearly understood. Reliability approaches should be used to complement conventional deterministic studies.

Jan 1, 2010

By Carel Robinson

MECHANIZATION of coal mine, is radically changing the requirements for under-ground transportation. It has increased materially the need for reliability and belt conveyors are the most dependable means of moving coal away from the place where it is mined. Their record of freedom from delays is almost 100 per cent. Why then are- not belt conveyors in more general use. Part of the answer lies in the pour records made at some of the earlier installations, and in the fact that belts have so long been identified as a type of equipment suitable, in the main, only to thin seams. Another reason is lack of knowledge of the full potentialities of belt transportation.

Jan 1, 1941

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By A. C. Fraker, H. H. Stadelmaier

In the systems Mo-Fe-C, Mo-Co-C, and Mo-Ni-C the phase boumdaries of the cubic Ij carbides were determined at 1000°C and the variation of the lattice parameter with composition was measured. In the system Mo-Fe-C a single ternary carbide, Mo3Fe3C, was observed. In Mo-Co-C and Mo-Ni-C two new n phases of the type M12C were found: Mo6C06C and Mo6Ni6C. At 1000°C they coexist with the M6C phases MO3-4,CO3-2C and Mo3-4Ni3-2C, respectively. Mo3C03C and Mo4C02C are not separate phases but parts of a single M6C phase region, and the same is true of Mo3Ni3C and Mo4Ni2C. THE n carbide structure type has been known since it was determined by westgren' in 1933, yet reliable information on phase compositions of this type is ap-parently scarce. The following selection of suggested formulas illustrates the extent of the confusion con-cerning compositions: W2-3Fe4-3C,1W6Fe6C,2 W2_4Fe4-2C,3 (W,Fe)6C,4 Tj.-W4Co2C and nz-W6Co6C,5 n1-W3Co3C and n2-w4Co2C,5 W3C03C and w6Co3C2,7 MO3Fe3C,8n2-M04Fe2C,9 (MO,Fe)6C,4 MO3CO3C,8 n2-MO4CO2C.9 Many of these compositions obviously overlap, some disagree in carbon content. The use of the designations 77, and n2 is not consistent. There is uncertainty whether two carbides M6C coexist or whether there is only one M6C with a wide range of substitution of one metal for the other. The existence of M12C seems questionable altogether if one ignores the results of a neutron diffraction study of W6Fe6C supporting that particular metal to carbon ratio.'' More reliable information is available for the iso-typic oxides studied by Nevitt,11 Nevitt, Downey, and orris," and Meussner and carpenter.l3 That n car-bides and oxides are structurally identical, particularly with respect to the location of the metalloid atom, has been demonstrated clearly by Stadelmaier and Meussner14 and also by Parthe, Jeitschko, and sadagopan.15 Therefore the present paper, which attempts to establish the phase boundaries of n defini-tively for three carbon systems, has implications for the whole family of filled Ti2Ni types. EXPERIMENTAL PROCEDURE The samples were prepared in two stages. Pellets weighing 3 g were compacted from powders of the elements and presintered in a closed tube of fused silica that had been evacuated to lO-4 mm Hg. This was fol- lowed by arc melting the sintered samples under argon. Remelting the button once was sufficient to produce homogeneous specimens. The metal powders had the following minimum purities in wt pct: molybdenum 99.5, iron 99.0, cobalt 99.7, nickel 99.9, graphite 99.94. Carbon determinations by the gas volumetric method were obtained from thirty-one of the one hundred samples in the annealed condition. They were limited to compositions that were critical to placing a boundary line in the isothermal sections. The carbon losses were comparatively low and averaged less than 1.5 at. pct. For annealing, the samples were sealed in tubes of fused silica evacuated to 10-4 mm Hg. The annealing schedule was 20 hr at 1250°C followed by 150 hr at 1000" ±10°C. For the water quench the silica glass tubes were broken mechanically to speed the quench. The specimens were examined in the as-cast and annealed condition by standard metallographic techniques. Some of the as-cast and all annealed samples were studied by X-ray diffraction using a 114.6-mm powder camera with filtered Co radiation. The lattice parameters of the n phases were determined by graphic extrapolation to 8 = 90 deg on a plot against sin2 8. It is estimated that the maximum error in the lattice parameters is ±0.002A.. The phase fields were determined by the disappearing phase method, relying on X-rays for phase identification and on microscopy to detect small amounts of a phase. RESULTS Pertinent information on the binary side diagrams has been summarized by Hansen and Anderko16 and Elliott17 and will not be discussed further. Photomicrographs documenting the equilibria at 1000°C have been selected to avoid redundancy due to the similarity of the three systems. Thus there will be only one picture showing an equilibrium with Mo2C, and so forth. Molybdenum-Iron-Carbon. An isothermal section of most of the Mo-Fe-C system at 1000°C is shown in Fig. 1. No attempt has been made to distinguish between a and y iron or to determine their phase boundaries. A conspicuous absence is the phase Fe2 1Mo2C6 with the Cr23C6 structure, supporting the suggestion by Krainer4 that it decomposes by annealing at high temperatures. The only ternary phase is found in a narrow range around Mo3Fe3C (MO43Fe43C14). A microstructure with a two-phase mixture of Mo + n is seen in Fig. 2. The variation of the lattice parameter of n with the estimated composition is shown in in Table IA. The phase diagram does not agree with the results of Kuo9 who reported n2-Mo4Fe2C. Our lattice parameter Varies from 11.095A at the iron-rich end to 11.140Å at the molybdenum-richoend of the phase field whereas Kuo9reported 11.26Å for Mo4Fe2C. We are in agreement with the older work

Jan 1, 1970

By V. T. McLemore

New Mexico Bureau of Geology and Mineral Resources (NMBGMR) has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills and geochemistry, as well as photographs and bibliographic resources. The available data includes location, production, reserves, geologic, geochemical, resource potential and other data. The National Uranium Resource Evaluation (NURE) stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during the 1970s. The NURE hydrogeochemical data provides analyses of water samples. ArcMap includes the location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production and possible environmental concerns, such as physical hazards (i.e., hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By Pengfu Tan

A thermodynamic model has been developed to predict the distribution behaviors of Cu, Fe, S, O, Pb, Zn, As, and heat balance in a lead blast furnace. The modeling results have been validated by the plant data of a lead smelter in Asia. The model can be used to predict for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen-enriched air. The effects of the blast air, industrial oxygen, and coke charge on the distributions of Cu, Fe, S, O, Pb, Zn, As, and heat balance, and on the lead loss in slag have been presented and discussed.

Jan 1, 2005

By K. Mohamed, G. Rashed

A conventional mechanical anchor bolt consists of a smooth bar threaded at the anchor end, with a conical wedge, and a mechanical shell anchor. When the smooth bar is torqued, the conical wedge pushes the shell anchor against the borehole wall. Coal mines use mechanical bolts in addition to other types of bolts to control the deformation and stabilize the yielded coal ribs. Limited research has been conducted to understand how a mechanical anchor performs in a coal rib. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted the study described in this paper to define the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of a mechanical rib bolt. Based on the strength of the coal seam and the conditions of the coal mines, the bolts were installed at different amounts of torque. A typical tri-linear load-deformation response was obtained from these tests. It was found that the anchorage capacity depends on the coal strength, and the anchorage stiffness depends on the installation torque. The outcome of this research provides essential data for rib support design. INTRODUCTION Rib falls are a serious hazard in underground coal mines. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Although resin bolts has been used increasingly in the last few years to control coal ribs, mechanical bolting (mainly expansion-shell bolts) is still used in many underground coal mines. Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 79% of the mines determine their rib support requirement based on the depth, mining height, and the loading conditions, of which 35% use the conventional mechanical bolts. Conventional mechanical bolts are preferable for rib support because they do not require the miners to be too close to the rib during rib bolting. Hence, using the conventional mechanical rib bolts can reduce the risk of injuries and fatalities during the installation process. The mechanical bolt or the point-anchored bolt is the oldest type of rock bolt that is still in use today. The point-anchored bolt is a tensioned bolt anchored down the hole with a mechanical expansion shell or a grouted medium (Peng and Tang, 1984). Figure 1 shows the components of the mechanical anchor bolt. The mechanical anchor bolt consists of a plug, a shell anchor, a headed smooth bar with the top end threaded, a bearing plate, a hardened washer, and sometimes a friction-reducing washer. The shell anchor can be either standard or bail type. The shell of the standard type is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the smooth bar is generally 5/8 in for the #5 bolt or 6/8 in for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the wedge down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall.

Jan 1, 2019

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

By S. G. Shabestari

Thermal analysis is a tool that is generally employed to predict the structure of the alloy before the actual casting is carried out. By cooling a sample of the molten alloy and recording the temperature-time curve, important solidification events may be analyzed by using the first derivative-cooling curve. In this research, strontium is added to (AS5U3G) 319 aluminum alloy and its influence on the formation of intermetallic compounds e.g. Al15(Mn,Fe)3Si2, Al2Cu, Al5Mg8Cu2Si6 formed during pre- and post-eutectic reaction have been investigated. Also any changes in solidification parameters such as temperature of Al-Si eutectic under cooling and temperatures of nucleation and growth of each phases caused by strontium addition, have been determined via the first derivative cooling curves. The effect of strontium on the formation of various intermetallic compounds has been studied by using very accurate thermal analysis equipment and the microstructures were analyzed using an optical microscope. The various phases reported in this paper were identified using Scanning Electron Microscopy (SEM) and linked to Energy Dispersive Spectroscopy (EDS). Formation of all pre- and post-eutectic phases was interpreted by comparing the phases formed in the microstructure and the reactions detected by using cooling curves. The results of this research indicate that thermal analysis technique can be used as an on-line process control in the production lines in aluminum casting industries.

Jan 1, 2004

By Moonkyung Chung

Static pile load tests were performed in order to evaluate bearing capacities and mechanical behaviors of three different pile types: (1) steel-concrete composite drilled shaft with rebar reinforcements inside the concrete, (2) steel-concrete composite drilled shaft without rebar, and (3) conventional drilled shaft (reinforcement concrete pile). The material elastic moduli obtained from pile load tests of steel-concrete composite drilled shafts with and without rebar reinforcement were found out to be similar. On the other hand, the elastic modulus of steel-concrete composite drilled shafts is almost twice as high as that of the conventional drilled shaft. The ultimate strengths of the steel-concrete composite drilled shaft with rebar, the steel-concrete composite drilled shaft without rebar, and the conventional drilled shaft were 9,810, 7,848, and 4,414kN, respectively. The results of these load tests reveal that the ultimate strengths of the steel-concrete composite drilled shaft with reinforcement and that without reinforcement are 2.22 times and 1.78 times greater that that of the drilled shaft. The structural failures of the steel-concrete composite drilled shafts occurred either at the boundary between tip of steel casing and rock-socketed concrete.

Jan 1, 2010

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By Avis W. Effinger

In conjunction with pilot steamflood tests in the Venango sands of Warren and Venango Counties, Pa., the Marx and Langenheim (4)3 calculations were adapted and programed for digital computer solution to predict test performance. The Monte Carlo technique was incorporated in the calculations to provide values of several variables which could not be adequately defined from available information. The computation methods are explained and the FORTRAN IV program listing is presented. Data and results of the prediction calculations for Venango oil sands are also shown.

Jan 1, 1969

By Robin P. Gardner

A radioisotope tracer method combined with a suitable back-calculation method is proposed and evaluated for the determination of model simulation parameters in open-circuit continuous ball mills. The method essentially consists of using impulse and/or step injections of short-lived radioisotopes of the naturally occurring trace elements manganese and sodium. It is evaluated here on the basis of the minimum standard deviations of the product weight-size distributions. These minimum standard deviations are taken as those predicted by a Poisson distribution of the number of particles present in size fractions of the samples taken for analysis. Previously developed tanks-in-series lumped parameter models are used in the evaluation. The results indicate that the method is very promising.

Jan 1, 1976

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the "carbon monoxide ratio") it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure· indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

By B. Z. Wu

The ore dressing of tin-polymetallic lean ores is a difficult problem and the research emphasis in domestic nonferrous metals mining field. Through research and tackle key problem,and in order to supply reference in dealing with the same types ores, this paper expatiates the exploiture and appli-cation of six item new technology and technics in ore dressing of tin-polymetallic lean ores. It include the technics of multi-step compounding disposing tailings, grinding step by step, grinding and processing circularly technology, high thickness without circle flotation technology, dispersedly flotation tin step by step technology, exceed fine lean plumbum stibium zinc flocculation flotation technology, the synthetically recovery of waste water after ore dressing technology.

Jan 1, 2014

By M. Goto, F. Kubota

"In this study, we show the successful separation of rare earth metals, which are indispensable elements for the high-tech industry, from a solution containing a metal mixture by using a liquid-liquid extraction and liquid membrane based on ionic liquids. We employed newly synthesized N, Ndioctyldiglycol amic acid (DODGAA) as an extractant for rare earth metals. The DODGAA exhibited a high affinity for rare earth metals such as Y, Nd, Eu and Dy and the extraction efficiency was greatly enhanced in ionic liquids (ILs). Furthermore, stripping of the metals was readily achieved by using an acid solution. INTRODUCTIONRare-earth metals have important applications in cutting-edge technologies employed in the electronics, information technology, and automobile industries. As Japan does not have many natural metal resources, maintaining a steady supply of imported rare-earth metals is important. The total amount of rareearth metals imported into Japan was 19,000 tons/year in 1996, and this amount increased to 40,000 tons/year over the following decade (Kramer 2010). Japan is now one of the world’s major importers of rare-earth metals (Kramer 2010). However, more than 90% of the rare-earth metals imported into Japan come from China, the world’s leading supplier of rare-earth metal resources, due to their low costs. This situation made us realize the importance of a second resource of rare-earth metals: “urban mines” or discarded electronic waste. Rare-earth metals are generally separated from their natural ores by solvent extraction. However, since urban mines have different metals and the concentrations of rare-earth metals are usually low, highly efficient separation and recovery methods are required for rare-earth metals.Recently, ionic liquids (ILs), which are molten salts at room temperature, have attracted considerable attention since they are novel, environmentally friendly solvents (Kubota & Goto, 2006; Han & Armstrong, 2007). The use of ILs in liquid-liquid extraction of rare-earth metals has been reported (Kubota et al., 2012). In some cases, the IL-based systems showed better extraction ability and selectivity than those showed by the conventional organic solvent extraction systems(Nakashima et al., 2003, 2005; Hirayama et al., 2008; Fang et al., 2012). Therefore, more efficient solvent extraction processes by using ILs can be developed. In this study, we investigated solvent extraction processes in which ILs are employed and discuss the possibility of using ILs in the separation and recovery of rare-earth metals from electronic waste."

Jan 1, 2012

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998