Search Documents

By Joseph Hirschi, Naga S. Y. Tirumalaraju, Aditya Mishra, Anthony (Sam) J. S. Spearing

"Primary roof support in underground coal mines in the USA consists mostly of fully grouted passive rebar or grouted (partially or fully) tensioned rebar. Research conducted at two room-and pillar coal mines in the Illinois Basin and one longwall mine in Colorado monitored the performance of these passive and active rock bolts under similar geologic and mining conditions and found no significant initial loads in either passive or active rock bolts (Spearing et al., 2011). Active rock bolts showed significant loss of initial pre-load, although the exact reasons for this were not fully investigated. Subsequent laboratory testing has also shown that in weak rock, resin creep occurs, caused by slippage of the mechanical key between resin column and rock interface. These creep tests were studied in the laboratory in an effort to quantifythis phenomenon.INTRODUCTIONResin-grouted rock bolts are the first and main line of defense to counter roof and rib falls in underground coal mines of the United States. Rock bolts are categorized as active or passive. Active bolts are tensioned during installation whilst no (or limited) tension is applied to passive bolts, which need subsequent strata movement to generate reactive loads. During installation of passive bolts, some reactive pre-load may be generated by a significant up-thrust from the rock bolter boom.The selection of active or passive bolts is critical and is mostly dependent on the conditions and properties of the immediate roof (Unrug, 2009). This decision is frequently made based on personal experience, bias, and most recently cost. Active bolts are generally used in cases of highly laminated roof rock. When active bolts are tensioned, they develop compressive forces between these layers forming a beam, which helps to stabilize weak individual layers thereby increasing frictional forces between layers and decreasing effects of horizontal stresses. The fully grouted tensioned rebar system is high in stiffness as compared to mechanical bolts and provides higher surface area of contact along the length of the bolt due to the grout, which permits it to develop a strong anchorage mechanism."

Jan 1, 2015

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By Antonio Fabiano de Oliveira

Estudos de laminação com revestimento de cromo e influência nas propriedades foram realizados com o objetivo de aumentar a produtividade dos cilindros. Para tal, foram utilizados cilindros cromados para laminação de chapas de cobre, com amostragem da técnica de réplica epoxy. A compreensão da correlação entre microestrutura e propriedades do material é objeto de grande interesse e, ao mesmo tempo, necessário para aplicação prática na laminação a frio, combinando revestimento e produtividade. O objetivo da pesquisa atual é comparar as propriedades tribológicas do cobre antes e depois da laminação, no cilindro de trabalho e chapa, com e sem revestimento de cromo.

Oct 30, 2017

By A. W. F. Smith, P. B. Prangnell, D. N. Crowther, P. J. Apps

It is well known that the refinement of grain size in metals leads to a significant improvement in important mechanical properties. As part of a European collaborative project, processing schedules have been investigated aimed at producing a homogeneous ultra-fine ferrite and spheroidised carbide aggregate microstructure structure in high carbon (CMn) steels (0.6-1.2wt%C), via conventional 'warm' rolling and innovative Equal Channel Angular Extrusion (ECAE). Suitable deformation schedules were determined from dilatometry and thermo-mechanical Gleeble simulations. Evidence of an ultra-fine ferrite and carbide aggregate microstructure following 'warm' rolling is given. A significant improvement in tensile strength, particularly proof stress (0.2%) was also noted in comparison to material deformed at higher temperatures. Concurrent Equal Channel Angular Extrusion (ECAE) experiments investigated microstructural evolution with incremental strain. Extensive analysis was carried out using various techniques, including high resolution Electron Back Scattered Diffraction (EBSD). Evidence of ferrite grain refinement was noted in a eutectoid composition steel. A sub-micron ferrite structure was observed following high strains (E-3.33) and the mechanical properties exhibit a marked increase in tensile strength.

Jan 1, 2004

By Arnold R. Pasieka, George V. Sotirow

"The object of this paper is to outline a computerized net cash flow approach for practical cutoff grade determinations. A cutoff grade carries not only geological but also economic value, in which costs are balanced against revenues. For different situations, cutoff grades are a 'standard of value' that are determined for the purpose of classifying economic or uneconomic mineral reserves in a specified time frame. In a constantly changing technical and economic environment, the decision to develop or maintain a mining operation at its best economic potential, requires an appropriate cutoff grade strategy, a strategy consistent with short- and long-term operational and corporate objectives and one based on realistic marketing and metal prices forecasts. The use of a project evaluation computer program, in combination with specific corporate net cash flow requirements, shows the most promising and flexible team approach for cutoff grade optimization.IntroductionThe recent recession has had a devastating effect on the Canadian mining industry. Exploration and mining R&D expenditures have been critically reduced and now are believed to be below healthy levels. Ore reserves, mine life and cutoff grades are careening in several directions because of low base metal prices, relatively high costs and sensitive precious metal prices.These conditions demand an improved understanding of the terms ""ore"" and ""cutoff grades"" as they are applied to the planning process and day-to-day operations. ""Ore"" or 'ore reserves"" is a dynamic concept, reflecting a cumulative effect of changes in geological, technical and economic conditions in terms of material which can be mined at a potential profit. By contrast, if economics are not the primary consideration, the term ""mineral reserve"" or ""mineral inventory"" should be used to describe the mineral deposit. For different situations, cutoff grade is ""a standard of value"" determined for the purpose of classifying mineral reserves as economic or uneconomic in a specified time frame. The question of mining at average reserve grade or low-grade material during high metal prices is of paramount importance for cutoff grade strategy."

Jan 1, 1985

By L. J. E. Hofer

This Bureau of Mines study, part of a broad program of research in air pollution related to minerals, was conducted to determine the nature and extent of the poisoning of catalysts when used to remove certain air pollutants from exhaust gases. The poisoning examined in this investigation occurs when leaded gasoline is used as a fuel for automotive engines. This research was conducted in cooperation with the Public Health Service. The smog in the Los Angeles area is attributed to the effect of radiant energy on the mixture of hydrocarbons and nitrogen oxides found in the atmosphere there. A large portion of the hydrocarbons is believed to originate in the exhaust gases of automobiles. To prevent the escape of these hydrocarbons into the atmosphere catalytic mufflers have been proposed. In principle, these are simple and nonmechanical, consisting of a vessel charged with a catalyst capable of destroying the exhaust hydrocarbons by catalyzing their oxidation. However, these catalysts are severely affected by the particulate matter, mainly in the form of lead sulfate (PbS04), lead oxysulfate (PbS04.Pb0), and Lead chlorobromide (Pb(Cl,Br)2), contained in the exhaust gas. Deposition of lead on the catalyst as PbS04, PbS04, PbS0, and Pb(Cl,Br)2 restricts catalytic activity. As a result,after 20,000 miles of operation the temperature necessary to achieve 50-percent conversion of isopentane in a mixture of 0.2 percent isopentane, 2 percent carbon monoxide and 4 percent oxygen, and the balance nitrogen at 10,000 hourly space velocity has risen from 400° C. to 500° C. even with a catalyst taken from the exit portion of the catalyst bed. The rest of the catalyst was more severely affected. Therefore, it would appear that operation for 20,000 miles is near the limit for a catalyst.

Jan 1, 1963

By E. H. Crabtree

This paper traces the experimental and pilot plant work completed by the authors since 1939 including the various methods which have been developed in applying coarse activated carbon to cyanidation. The methods and results developed by the authors in desorbing gold and silver from carbons are given and the possibilities for the re-use of the desorbed carbons are discussed

Jan 1, 1950

By D Brereton, C J. Moran

In this era of rising focus on the social and environmental costs and benefits of mining operations, the valuation methodologies used to assess such impacts become increasingly important. Within an industry dominated by an engineering culture that places emphasis on net present value (NPV) calculations using high discount rates, difficulties often arise when attempting to justify projects with longer-term, harder to quantify benefits. This is particularly so when these benefits fall in the social and environmental domains and involve other stakeholders. In this paper, we summarise the results of a recent literature review on this subject, which focused on the valuation of æBeyond ComplianceÆ initiatives in the mining sector. We discuss a range of approaches including the quantification of hidden internal costs, financial methods of incorporating risk into calculations, the integration of quantitative and qualitative information, and also the valuation of æexternalitiesÆ or costs and benefits borne by others. We then use a series of examples relating to the management of water in the minerals industry to illustrate how some of these approaches could be applied. There are high-level commitments from both individual companies and groups such as the ICMM to incorporate sustainable development criteria into decision-making processes within the industry. We conclude the paper by arguing that, to meet these commitments, there is a need for the industry to adopt a broader range of valuation methodologies than appears to be the case at present.

Jan 1, 2006

By Schumacher, Earle E.

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10" C. in temperature. The precise location of this line is also important in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By R J. Longbottom

In this study the bonding within reduced titanomagnetite-coal compacts was investigated. The aim of the study was to better understand the binding mechanisms in the reduced compacts and, based on this understanding, to improve on their strength.Titanomagnetite ore was combined with sub-bituminous coal to form compacts. The compacts were then reduced by heating in a thermogravimetric furnace (TGA) to temperatures between 1000 - 1300°C under argon. The reaction progress was monitored by measuring the weight loss with time. The reduced compacts were found to have low strength in compression testing. The main form of bonding between the reduced titanomagnetite particles in the compact was by the formation of a slag-like material. Increasing the fi nal reduction temperature was found to have a profound effect on the strength of the compacts by promoting the formation of this slag-like material.Attempts to improve the strength of the compacts were made by changing two variables, the type of coal and the addition of rice husks. The addition of coking coal gave reacted samples that had little strength, while the addition of rice husks may have enhanced the strength of the reduced compacts.

Jul 11, 2011

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

By AIME AIME

No democracy such as ours, can ever be prepared for war, because we could never conceivably be the aggressor. The aggressor prepares in secret, designs his new tactics, and invents and makes new equipment and selects the time to strike. If a democracy prepare done year and the war came later, all that it had one would have to bed one over. All that England has today in the way of effective armament has been invented, designed, made, and the crews trained since the war began, because the totalitarian aggressor introduced new types of equipment and new techniques.

Jan 1, 1941

By Carl Belser

This report is the first of a series dealing with the oil-shale reserves of the Green River formation in the Rocky Mountain Region. The known oil-shale reserves of northwestern Colorado at present considered to have economic value apparently are confined to the Piceanco Creek basin between the Colorado and White Rivers. The number of sampled sections is small, but there can be little doubt that the Piceance Creek basin is a potential source of enormous quantities of liquid fuels and the related byproducts obtained from oil-shale processing. The partly blocked and inferred oil-shale reserves of 25-gallon-a-ton shale are estimated to have an oil yield of 125 billion barrels and the reserves of 15-gallon-a-ton shale are estimated to have an oil yield of 494 billion barrels. The number of available sampled sections is inadequate for making firm estimates.

Jan 1, 1951

By Carl E. Williams

Several years ago it was decided that ASARCO was in need of a good mine scheduling program to complete the computerized open pit mine planning package that was being used on new prospects and operating properties. A trial and error approach was being used to schedule a mine on a year by year basis, but this was time-consuming and far from offering an optimum solution l. Due to the magnitude of time and expertise required to develop such a sophisticated computer program, it was decided to search outside of the company for one already developed and available for purchase, This proved fruitless and therefore proposals were requested from consulting firms that had the expertise to develop such a program. Out of the five firms that submitted proposals, the one chosen was Systems Control, Inc., (S.C.I.) of Palo Alto, California. S.C.I. was selected because it was felt that they offered the greatest capability in the mathematical solution of complex problems. But due to their lack of mining expertise, a cooperative venture was developed whereby ASARCO would supply this mining knowledge. The selection of this vendor, the formulation of the contract and specifications, and the development of the computer program required about 3 years to accomplish.

Jan 1, 1973

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By J. B. Austin

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measure-ments serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transforma-tion temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chro-mium or managanese. The lag, or undercooling, observed at the ? - a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2

Jan 1, 1935

By J. B. Austin, R. H. H. Pierce

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of, carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is .cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ?-a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dilatometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has. been described.2

Jan 1, 1935

By C. A. Pickles

Nickeliferous limonitic laterite ores contain considerable free moisture. In this research, the application of microwave radiation for the drying of this ore was investigated. The effects of sample mass, initial moisture content and porosity on the microwave drying rate were studied and the results were compared to those obtained with conventional drying. Microwave drying rates of two to three times the conventional values were achieved. Further enhancement of the microwave drying rate was realized by increasing the flow rate of air over the sample or by operating at reduced pressure. The high microwave drying rates were attributed to the inverted temperature gradient which resulted in internal heating and boiling and this in turn promoted movement of the water, both as liquid and vapour, to the surface.

Jan 1, 2005

By H. Rosenberg

Haldor Topsoe A/S has developed its WSA technology to meet the demand in the market for a simple and reliable process that converts sulphurous emissions from off-gasses into high-grade sulphuric acid. With more than 50 references in 25 countries, the WSA technology has proven its ability to generate acid at 98% concentration, efficiently and economically. The wet gas sulphuric acid (WSA) technology treats the furnace off-gas directly from upstream gas cleaning plants. No further drying is required, since the humidity present in the off-gas is used to hydrate the SO3generated in the converter and produce sulphuric acid. The heat generated during the oxidation, hydration and condensation processes is principally reused in the process to preheat the off-gas to the required temperature level, and also to generate high pressure superheated steam for process use. This advantage of steam production, coupled with lower water and power consumption requirements, is particularly important in the African production environment. Having fewer process components than conventional acid plants, the WSA technology is a simple and compact operation, which makes it easier to retrofit into an existing smelter plant. Further, the WSA technology simultaneously offers the possibility to treat multiple gas streams arising within the production facility due to superior flexibility in terms of SO2concentration and turndown ratio.

Jan 1, 2006

By M Wimmer

LKAB operates two underground iron ore mines located in the northern part of Sweden, both using sublevel caving (SLC) as the mining method. Knowledge of the mechanisms of gravity flow is important since it affects both ore recovery and waste dilution. This paper describes results from a large-scale field test carried out at the Kiruna mine with a focus on gravity flow. It is part of Work Package 2 in the I2Mine project financed by the EU. A total of ten rings were blasted. Smart Markers based on radio frequency identification technology were used to monitor the gravity flow. An accurate delineation of the isolated extraction zone requires reliable detection of all recovered Smart Markers and precise knowledge of the 3D position of the markers within the burden. It was therefore necessary to carry out borehole deviation measurements (collar, alignment and trajectory). The blast performance was monitored by high-speed filming, near-field vibration monitoring and velocity of detonation measurements. Three-dimensional stereo images were taken from the drawpoint and the loaded bucket after each mucking cycle. Based upon that, fragmentation was assessed both in 2D and 3D. Furthermore, volumetric differences were determined at the drawpoint, which reflects the mobility of loaded material. For draw control, the Fe content is estimated by measuring weight and assuming a full bucket. The measured volume of rock in each bucket further improves this estimate. Possible flow disturbances occurring at the drawpoint were revealed by video recording. Two-dimensional laser scanning was carried out during mucking to track the position of the bucket and estimate the position and slope of the muck pile.The results from this test clearly show that the gravity flow in the large-scale sublevel cave in Kiruna mine is often of disturbed character. Standard draw occurred only in three rings and shallow draw in the remaining seven rings. In five cases, shallow draw developed towards standard draw, but occurred at rather late stages during extraction (70–125 per cent). The maximum width of the draw varied between 10 m and 13 m except for one ring (6 m). The draw reaches the cave rather early (5–25 per cent extraction) in shallow draw situations and much later (about 50 per cent) during standard draw. Waste originates from above in most cases, while more significant portions often occur at about 20–45 per cent extraction.All the results from this extensive field test are not yet fully analysed, and further field tests are planned. A more detailed insight into gravity flow in large-scale SLC and possible influence by drilling, blasting and the mucking procedure is expected in the future.CITATION:Nordqvist, A and Wimmer, M, 2016. Holistic approach to study gravity flow at the Kiruna sublevel caving mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 401–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016