Search Documents

By Travis Coleman, Elvis Ishimwe

Currently, more than 400 drilled shafts have been constructed by various contractors at the I-90/94 and I-290 Jane Byrne (Circle) Interchange, located near downtown Chicago, Illinois. Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) tests were performed to evaluate the integrity and concrete quality of the drilled shafts installed at this project. For Phase I of the project the shafts were tested using CSL methods, and the shaft integrity was identified by analyzing the First Arrival Time (FAT) and the signal strength (energy) measurements. For the major portion of Phase II, the Illinois Department of Transportation (IDOT) accepted TIP testing as a substitute for CSL at the request of the contractors. The CSL testing results indicated 54 percent of the tested shafts had anomalies, and 78 percent of these anomalies were located within the lower three diameters of the shafts. To date, TIP testing results indicated the shaft integrity was as expected and acceptable for the all 34 tested shafts. A review of the testing results and a discussion of the detected anomalies are presented. In addition, a comparison of both TIP and CSL measurements is presented in this paper.

By J Jackson, M F. Young

"Ore is the economic portion of a mineral deposit that can be extracted economically. Hence an ore type is a classification of the ore based on one or more dominant characteristics in order to enable communication between unit operations and/or technical disciplines.In project evaluation, ore types are often defined early based on geological observations by geologists and initial metallurgical testing is based around this classification even though a number of processing options can be under evaluation. However, the geological drivers of performance for each of these processes can be very different and the ore type classification for one process may not be relevant for another. In operations an ore type, as either defined in the project evaluation phase or those that evolve with additional knowledge, is unlikely to provide the knowledge required across all the unit operations. The ore type has a meaning to someone but does not necessarily for all unit operations across the value chain.Geometallurgical or orebody knowledge has evolved through the consideration of multiple processes within the value chain, the improved understanding of variability of process performance within ore types and the effect on the complexity of the mineral extraction processes. Furthermore orebody knowledge has been moving from personal based knowledge and understanding to a more process oriented approach where measurement and spatial and process performance modelling is playing a greater role. Advances in mine planning and scheduling allow for both detailed analysis of the block model and the expected extraction processing attributes across various time scales. This capability of analysing and describing the complexity still requires to be communicated to the various unit operations, which may be beyond the traditional classification of an ore type.The limitations of an ore type and potential alternatives to enable the relevant information to be communicated to the relevant groups are outlined through a number of case examples across the value chain.CITATION:Jackson, J and Young, M F, 2016. Ore Type – Everything to Someone but Nothing to Anyone, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A. W. Fahrenwald

Flotation practice in Idaho is now about 13 years old. The advance has been steady during these 113 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. Ores of the District The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and' 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By J. C. Heter

Industrial Mineral Fillers, LLC. is in the initial stages of mining and processing Anorthosite (CASPAR TM) at its CASPAR mine located in Soledad Canyon, Los Angeles County, California The CASPAR is being mined from the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. Preliminary results suggest that CASPAR is a desirable alternative to silica sand used in construction applications, such as, stucco, grout, abrasives, and other uses including filtration and golf course recreation sands. With the use of standard ore dressing techniques, CASPAR is suitable for use as a filler in paint, plastics and rubber. Environmentally, CASPAR has advantages over silica sand, in that, there is no detectable Free Silca.

Jan 1, 1997

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By S. Dey, C. Bhar, S. K. Mandal

Loading and hauling of ore and waste are the key operations of an opencast coal mine and entail a high operational cost. The productivity of a mine can be increased by reducing the cycle time of loading equipment as well as utilizing dumpers optimally. In this paper we discuss the impact of rock type, bucket fill factor, rock fragmentation, the height of the cut, and angle of swing of the bucket on shovel performance. A time study is conducted on shovels in an opencast coal mine with experimental blasts of rocks to assess the impact of different factors on the performance of the shovel. Based on the data, the authors applied multiple regression (MR) and artificial neural network (ANN) techniques to develop different models for the prediction of the shovel cycle time. Developed models are validated by comparing the predicted data with actual field data. With the help of the best model, the plausible fleet size is determined in order to utilize the shovel and dumper optimally and to improve the performance of shovel–dumper operation.

Oct 1, 2022

By H. Kinilakodi

In 2008, the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using a sample of 103 mines with 2008 and 2009 data, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performances as compared to large and medium-sized mines.

Jan 1, 2011

By Patricio F. Mendez

This paper presents a formalism to automate portions of the traditional scaling procedure. This formalism, called here Order of Magnitude Scaling (OMS), captures essential components of the governing equations into a set of matrices and arrays amenable to computer implementation using standard linear algebra tools. This approach is valid and specially useful for large systems of multicoupled equations. The matrix approach proposed enables one to automate operations such as normalization, dominant balance, obtention of characteristic values, and check for self-consistency. Also, automation permits an exhaustive exploration of all possible balances and the discovery of unsuspected scaling laws. As an example, OMS is applied to the analysis of the viscous boundary layer with no external pressure gradient. The obtained scaling laws for boundary layer thickness and transverse velocity are the same as those obtained with traditional scaling, and in addition, a meaningful estimation for pressure variations within the boundary layer is obtained; this last estimation is typically not addressed in the manual analysis.

Jan 1, 2006

By Ahmed M. Yousif, Walid M. Abdellah, Galal M. Abdel Wahab, Amal E. Mubark

The present work is concerned with selective dissolution of niobium from Gabal El Faliq concentrate sample by using fluoridefree process. The chemical analysis of concentrate sample revealed the presence of high amount of ZrO2, Nb2O5, Re2O3, and HfO2 assaying 33.6, 1.99, 4.8, and 1.2%w/w respectively. Several economic minerals including zircon, samarskite, fergusonite, and xenotimewere recorded in the studied sample. About 98%of Nb content was selectively dissolved at the optimumconditions of 1:2 concentrate sample: KOH weight ratio, 2.5 h fusion time, and fusion temperature of 550 °C. Organic solvent extraction process using Aliquat 336S in xylene was effectively used for preparing pure Nb2O5 (98.95%).

Oct 22, 2019

By Allana Cristina Pires Ferreira

O endurecimento secundário de aço rápido AISI M3:2 nome comercial Sinter 23 obtido por uma técnica de metalurgia do pó de sinterização por compactação isostática a quente é objeto desse trabalho de pesquisa. O aço rápido em questão foi austenitizado em banho de sal a 1.140°C, 1.160°C, 1.180°C e 1.200°C, temperado ao ar e revenimento a 540°C, 560°C e 580°C. Amostras do aço rápido foram fabricadas e submetidas ao tratamento térmico acima descrito e submetida a ensaios de dureza Vickers e Rockwell C para a determinação das suas respostas ao tratamento térmico de endurecimento e avaliação do pico de endurecimento secundário através dos resultados de dureza.

Aug 16, 2017

By A. J. Lyon

THE stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening; which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging-heating in a temperature range below 170° C. (340° F.)-will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1928

By G. Dodbiba, T. Fujita, M. Kawata, S. Yamasaki, K. Mitsuhashi, J. Ponou, Y. Iwazaki, T. Atarashi

"The grade of copper ore and concentrate is recently decreasing and it will continues decrease further in the future. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper concentrate is becoming even more important. In this work, the magnetic separation of copper concentrate by heat treatment and the flotation of low grade copper ore by microwave irradiation was studied. The heat treatment of copper minerals in the air atmosphere, the magnetization of most copper minerals increases and especially the magnetization of chalcopyrite shows the largest magnetization, after being heated at 500 oC. The wet HGMS of copper concentrate has been studied and the results have then been compared with the ones when calcined concentrate was used instead. The microwave treatment before ball milling increased the degree of liberation up to 100%, especially when compared with the case when only ball mill was applied to the as-received ore. The flotation of ground copper ore after microwave irradiation showed that the grade copper minerals such as chalcosite and bornite in froth part is much larger than that of tailing part.INTRODUCTION The copper has been used many kind of technological fields and will be more important for the future technology. The global copper production from mine is predicted as shown in Figure 1 (Northey, S. 2014). The copper production peak will be appeared in 2030 and the demand peaks in 2040. In the future the recycling of stocked copper and copper alloy will be necessary to satisfy the demand (Yoshimura, A. 2018). Changes in the grade of copper in copper concentrate, exported from several countries are shown in Figure 2. The copper grade in copper concentrate after mineral processing is gradually decreases every year and it is less than 30% nowadays. On the other hand, the copper ore grade change and prediction are shown in Figure 3. The grade of copper ore is also decreasing to less than 1% in 2010 (Northey, S. 2014). In the future the copper grade gradually decreases, reaching to less than 0.5% in 2080 and the energy to produce the copper metal will increase. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper minerals become more important, nowadays. The microwave irradiation of copper ore for the liberation, energy etc. has been reported by several researchers (for example, Batchelor, A.R. 2017). The magnetization change of copper ore by heating has been reported to remove the arsenic (Sawada, M 2015). In this report, the magnetic separation of copper concentrate by heat treatment and the flotation of copper concentrate by microwave irradiation are discussed after the characteristics of secondary copper minerals are investigated by these treatments."

Jan 1, 2018

By Norihisa Iida, Yutaka Koshiba, Tsutoipu Masui

"Mitsubishi Materials has many years of experience in the production of oxygen free copper (OFC) and its alloys with a fully continuous-casting process. Four grades of OFC, commercial, electronic, superconductor, and ASTM class I are available according to user needs such as stabilizer for superconductivity, magnetron, and ultra-vacuum systems. Along with Cu-Ag and CuSn, we offer OFC based copper alloys such ·as Cu-Cr-Zr, Cu-Fe-P, Cu-Ni-Si and others, that are suitable for lead frame and connectors. Within the maximum sizes of 260mm X 1050mm for cakes and 385mm diameter for billets, we are very flexible and can adjust the ingot size to customer’s requirements. Other products that we can supply are semi-finished products such as hot rolled sheet, ·forged blank, extruded rod and finished products like mold for continuous casting of steel, ring mold for non-ferrous casting and backing plate for sputtering target.IntroductionMitsubishi Materials Corporation developed mass produced high quality oxygen free copper and. high copper alloy ingots in the 1960's. We produce 60,000 - 70,000 tons annually giving us 22 - 23% share of the world's market.Our oxygen free copper and. copper alloys are produced with a fully continuous casting process using only high-grade copper cathodes from our Naoshima and Onahama refineries. The raw material is melted and cast in' a carefully controlled atmosphere resulting in a product with low impurities and excellent properties.Using a controlled atmosphere it is possible to produce high quality copper alloys including active elements like chromium (Cr), zirconium (Zr), titanium (Ti), and magnesium (Mg) which are difficult to produce using standard batch casting methods.Using our own cakes and ·billets we produce and supply worldwide wrought materials like molds for ferrous and non-femous casting. These products receive special patented thermo-mechanical· treatments resulting in high strength and excellent conductivity with low cost."

Jan 1, 2000

By R. S. Busk

TWO groups of binary alloys were prepared. The first group consisted of those elements relatively soluble in magnesium: Li, Al, Zn, Ga, Ag, Cd, In, Sn, Hg, T1, Pb, and Bi. These are predominately Group B elements. The second group consisted of most of the remaining metallic elements, all of which are relatively insoluble in magnesium: As, Au, Ba, Ca, Ce, Cu, Ir, La, Mn, Ni, Pd, Pt, Rh, Sb, Si, Te, Ti, W, and Zr. These are all Group A, transition, or rare earth elements. Alloys of the first group were prepared by melting sublimed magnesium and elements as pure as obtainable in a graphite crucible, using a standard flux1 for protection. The melts were poured into a small graphite mold to produce 3xY4 in. diam slugs. Spectroscopic analyses were made of each slug. In all cases, the total impurity content was less than 0.05 pct. The slugs were then heat treated 5°C below the eutectic temperature until complete solution, as judged metallographically, was obtained. Filings from the center of the slugs were compacted at room temperature into 1/2 in. long x 1/4 in. diam cylinders, sealed in pyrex under 1/2 atm of purified argon, annealed at the heat-treating temperature for 1 hr, and quenched in water. After the X-ray diffraction patterns were made, each compact was analyzed chemically for the solute. It was found that the Mg-Li alloys reacted during filing to reduce the Li in solid solution. For this series of alloys, the slug was cold worked, annealed in purified argon, the surface dissolved in dilute HC1 to a depth of about 0.005 in., and the X-ray exposure made on the fresh surface. This procedure resulted in sharp, continuous lines and in true values for the lattice parameters. The alloys in the second group were prepared in the same way except that about 1 wt pct of each solute was added. Since the solubility limit was exceeded, not all the solute dissolved. These alloys were analyzed spectroscopically only to confirm the presence of the solute. The diffraction patterns were of the back-reflec-tion type using the characteristic copper radiation* and a flat cassette. Both the film and the specimen were rotated. The specimen temperature was maintained at 25" ± 1°C. The films had sharp lines; their diameters were measured directly to 0.01 cm. The parameters were calculated from the line diameters using a modified version of Cohen's extrapolation method.2 his method effectively eliminates systematic errors such as film shrinkage, inaccurate alignment, and non-precise film-to-speci-men distance. The random errors were minimized

Jan 1, 1951

By Garth D. Kirkham

The Problem The Don deposit is a series of two sub-vertical zones that pose a number of challenges with respect to modeling and interpolation. The first challenge is that, based on data and observations, the mineralization and, more importantly, the grade is layered or banded and is stratigraphically controlled. The second challenge is that, due to the undulations of the deposit and extreme changes in dip, using a standard oriented ellipse to guide the estimation process is not appropriate and does not result in an estimate that is representative on a local scale. In order to solve this problem an adapted methodology of relative elevation modelling, has been devised to effectively model and estimate deposits faced with these challenges. Relative Elevation Designed for bedded seam and gridded surface With variable dip and vertical grade variability

May 1, 2013

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

By Ian Baker, Xavier Pierron

"Iron aluminides hold great promise for intermediate temperature applications (to ~ 600°C) because of their excellent oxidation and sulphidation resistance and good strength. However, they have poor low temperature ductility, a feature which is exacerbated by water-containing environments. This paper presents an overview of the effects of environment on the ductility of iron aluminides, including the effects of iron aluminum ratio; ternary alloying additions, particularly boron; strain rate; and temperature. The mechanisms involved in water-induced embrittlement are discussed.IntroductionOver the last few years, it has became increasingly evident that the ductility and fracture toughness of many intermetallic compounds, particularly aluminides, are reduced dramatically if they are mechanically tested in either air or in hydrogen-containing atmospheres (1-5). For FeAI and Fe3AI, it has been shown that water vapor, for example in air at room temperature, can form atomic hydrogen by reacting with the Al atoms (1, 2). As a result in iron aluminides, the environmental embrittlement process is quite similar to traditional hydrogen embrittlement. This can be easily demonstrated by either testing an iron aluminide in an environment free of the deleterious species or by testing at high strain rates, both of which result in greater ductility. The purpose of this paper is to review recent progress in understanding environmental embrittlement in FeAI and Fe3AI, and to consider possible environmental embrittlement mechanisms. Greater understanding of this phenomenon will lead ultimately to remedies to this problem which is a major reason for preventing the practical application of these materials. First, some background on the iron-rich aluminides."

Jan 1, 1996

One of the most important factors leading to the success of a cement plant is its location. A multicriteria decision-making method is used to rank alternative plant locations. The set of criteria is established and corresponding criteria should be established for each case study, although this multicriteria decision-making approach has broader applicability. In this paper, the analytic hierarchy process (AHP) with 5 criteria is used to develop a location evaluation hierarchy for an alumina?cement plant in East Azerbaijan province of Iran. Five alternatives for the plant location are evaluated. The main criteria are transportation, water supply, power supply, fuel supply and land. Other criteria have the same importance as these five alternatives. The alternatives are ranked by a multicriteria method and the best site is proposed. Keywords: plant location; multicriteria decision-making

Jan 1, 2005

By D. C. Sharpstone

THE Polaris-Taku mine is a new gold property, situated in the far north-west corner of British Columbia. Production was started in November, 1937, at the rate of 150 tons a day, and recently has been increased to 200 tons. The property, which promises to become one of British Columbia's important gold mines, was developed and brought into production in twenty-nine months after work was started on it as a virtual prospect in June, 1935, by Edward C. Congdon and associates. Inaccessibility, extraordinarily complicated geological problems, and difficult metallurgy retarded development of the property before acquisition by the present interests, an::l, in fact, discouraged two companies that had spent substantial sums upon it from continuing development. This paper is concerned with reviewing the development of the property and describing the principal features of the geology, the mining and metallurgical practices, and the equipment employed. Acknowledgments The writer is indebted to Mr. Edward C. Congdon, President of the Polaris-Taku Mining Company, and to various members of the mine staff for their assistance in assembling the data for this paper. Special thanks are due to Mr. George G. Griswold, Jr., of Butte, Montana, who generously and painstakingly prepared the section dealing with milling and power. Microscopic studies of ores were made by Professors Frank Grout an::l G. M. Schwartz, of the University of Minnesota, and by Mr. Griswold.

Jan 1, 1938

By G. A. Eltringham, A. F. Sarofim, A. A. Shook, M. P. Heap, B. R. Adams, K. A. Davis

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the different temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The improved kinetic parameters derived from the drop tube studies are used to simulate chalcopyrite concentrate reactions in the reaction shaft of an industrial smelter. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999