Search Documents

By Hong Yong Sohn

A novel flash ironmaking technology is under development at the University of Utah under the support of U.S. Department of Energy (DOE) and American Iron and Steel Institute (AISI). The history of the development from the conception of the idea to the current status will be discussed. The flash ironmaking process produces iron directly from fine iron ore concentrates without requiring cokemaking and pelletization/sintering, which will enable the technology to significantly reduce energy consumption and carbon dioxide emissions compared with blast furnace ironmaking. Unlike other gas-based ironmaking processes, this technology will not suffer from the problems of solid sticking and fusion. Current work is focused on the method of supplying the energy required to maintain the necessary temperature, as an intermediate step to determine the scalability for larger, industrial-scale pilot trials.

Jan 1, 2014

R. F. WOOD,* Sandusky, Ohio.-I made a few tests of gun-metal specimens, after I noticed the results on quenching -reported by the Bureau of Standards. The data of one such test are given herewith. The bars were heat treated and quenched before they were machined, and in all cases they were brought up to 700° or 800°. They became extremely brittle,, showed almost no elongation, except such as was caused by the failure of the pieces to fit together after they were pulled, and the tensile stength was reduced from around 35,000 to about 13,000 lb. per sq. in. In addition, the weakening effect of the quenching seemed to be almost as marked when the bar was allowed to slowly air-cool from red to black, and then quenched, as it was by quenching directly from the red heat. Test Bars.-Rough size, 9/16 in. diam. over test section, grips 13/16 in. diam. Cast two in a flask, one on each side of a block 8 by 4 by 1 in. and fin-gated thereto from the grips but not from the test section. Poured with flask in inclined position, with gate to lower end of block and riser from upper end of each test bar. Bars were machined to ½ in. over the test section, after heat treatment. Casting the Bars.-Charge of 1500 lb. consisting of 400 lb. of new metals and 1100 lb. of G turnings and scrap was melted in open-flame oil furnaces and then poured into a 1-ton ladle. From the ladle 150 lb. was poured into a preheated No. 50 crucible, land from this the flasks of test bars were poured. The six flasks are indicated below by the numbers 1 to 6 and the bars in each flask by the letters a and b, thus 4a and 4h, for instance, were the two bars in flask No. 4.

Jan 12, 1919

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

By Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and wash- ability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected was statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size-consist, and yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1974

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018

By M. Rafieazad, P. Fathi, X. Duan, M. Mohammadi, A. M. Nasiri

"Direct metal laser sintering (DMLS) is a metal additive manufacturing technology that creates highly complex components by fusing metal powder into a solid part. In this study, the impact of surface roughness on corrosion resistivity of AlSi10Mg_200C alloy manufactured through DMLS was investigated. The as-printed DMLS-AlSi10Mg _200C alloy was subjected to various surface finishing processes including grinding and sandblasting. The corrosion performance of the surfaces was then evaluated using potentiodynamic polarization testing and electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution to mimic seawater environment. Surface characterization and corrosion morphology of the samples were assessed by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy. The results of this study show that the surface finishing process and the resultant surface roughness has a significant impact on the corrosion resistivity of the DMLS-AlSi10Mg_200C alloy in the seawater environment.INTRODUCTION Direct Metal Laser Sintering (DMLS), also known as Selective Laser Melting (SLM) (Sames, List, Pannala, Dehoff, & Babu, 2016), Laser Beam Melting (LBM), or Laser Metal Fusion (LMF) (Herzog, Seyda, Wycisk, & Emmelmann, 2016), is an additive manufacturing process that utilizes a precise, high-power laser to micro-join powdered metals and alloys layer by layer to form almost fully dense and functional components in three dimensions from the 3D computer-aided design (CAD) data. Complex geometries not possible with conventional manufacturing processes can be readily manufactured with high accuracy using the DMLS process with no need to time-consuming tooling."

Jan 1, 2018

By N. Schreithofer

The deposition of octadecylamine (ODA) at the KCI crystal/NaCI-KCI brine interface was investigated using atomic force microscopy (AFM). The AFM images of freshly cleaved KCI specimens immersed in KCI-NaCI saturated brine at room temperature reveal disappearance with time of the atomic steps and formation of cubic NaC1 crystals. These crystals were found to form when the specimen was withdrawn from the saturated solution. Depending on the way of contacting the specimens with the octadecylamine dispersion, the AFM images show huge differences in the deposition patterns of ODA on KCI crystals. Adequate dispersion was found to help the formation of quite even ODA coverage. The coverage was several monolayers thicker when air/brine/solid contact took place, suggesting that in the potash flotation the collector is likely to be carried to the solid surfaces by air bubbles. The presence of methyl-isobutyl carbinol (M IBC) enhanced the dispersion of ODA in brine, thus helping the spreading of the surfactant on the KCI crystal surface.

Jan 1, 2006

By Amilton de Sousa Lins Junior

O presente trabalho faz parte de um amplo programa de pesquisas que envolvem o desenvolvimento de procedimentos de soldagem para componentes de sistemas de ancoragem de plataformas de petróleo. Particularmente, realiza-se um estudo das propriedades mecânicas de um metal de solda de alta resistência obtido pelo processo de soldagem GMAW para atendimento dos requisitos necessários para a soldagem de aços da classe IACS W22 Grau R4. Foram soldadas juntas multipasses pelo processo GMAW, com preaquecimento de 150°C, corrente contínua, posição plana e aporte térmico médio de 1,0 kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados integralmente do metal de solda depositado, tanto na condição de como soldado quanto após tratamento térmico pós-soldagem a 600°C por 1 hora. Os resultados mostraram que foi possível obter propriedades mecânicas que atendem os requisitos de aços da classe Grau R4 em todas as condições analisadas. Adicionalmente, verificou-se que o tratamento térmico pós-soldagem propiciou uma melhoria na tenacidade ao impacto devido ao revenimento da microestrutura do metal de solda.

Aug 8, 2018

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world's future needs for minerals - the needs which it is our industry's task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world's mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world's demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth's crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974

By Leopoldo José Naves Alves

Os sistemas de controle e supervisão de processos que não contemplam o adequado gerenciamento de alarmes e eventos sofrem uma sobrecarga na operação com um número exacerbado de informações durante situações de distúrbio e até mesmo operação normal. Nos últimos anos, a abordagem sobre metodologia, boas práticas e planejamento adequado do gerenciamento de alarmes vem sendo alvo de crescente interesse, seu objetivo é garantir um ótimo estado de produção e uma maior segurança dos equipamentos e dos operadores. Em 2009 a ISA, após anos de trabalho sobre este tema, apresentou a norma ANSI/ISA 18.2, formalizando conceitos, definindo metodologias e sugerindo boas práticas. Este trabalho visa apresentar de maneira objetiva tal norma e demonstrar a viabilidade e eficiência de sua aplicação pratica.

Aug 8, 2018

By Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano, Marcelo Mourão

The organic household waste has a growing disposal problem, requiring costly disposal systems. It is necessary to find new applications for these materials; one could be the steelmaking raw material production. In this paper is studied the development of self-reducing pellets from the organic waste pyrolysis, where is generated carbon and condensable and non-condensable volatiles. Non-condensable volatiles were burned and condensable volatiles were recovered. The resulting tar was mixed with iron ore, coal powder and flux (CaO), to then be pelletized together. Compression, falls and tumbler tests were conducted to characterize the pellets before and after heat treatment and reduction processes. The reduction curve and their physical and morphological characterization were measured. The results were as was expected, the fluidized coal create sufficient adhesion that pellets earned resistance with an equivalent resistance of common pellets, showing a good feasibility of this process.

Jan 1, 2015

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

By M. A. Bothwell

The purpose of this paper is to describe the methods used to select mill discharge screens, and to outline factors which should be taken into consideration when choosing screens for this application.

Jan 1, 2001

By R L. Koenig

The rediscovery and recognition of the magnetite potential of the iron mineralisation at the Hawsons Project area 60 km south of Broken Hill has the potential for the development of a new series of magnetite iron-ore operations across the Braemar Iron Formation in New South Wales and South Australia. Despite the low-grade of 16 per cent magnetite, the Hawsons project feasibility studies are indicating a positive business case for a large-scale 20 Mt/a of magnetite project for the following reasons:• The mineralisation is on a huge scale, with a major potential for increases beyond the already very large established resource of 1.4 Bt.• The mineralisation is particularly soft for crushing and grinding, with a Bond work index of 6.3 and an overall comminution power requirement of 6.7 kWh/t of ore. This equates to 39 kWh/t of concentrate which is significantly less than for similar projects.• The mineralisation fractures easily, preferentially along grain boundaries.• Location is close to mining infrastructure and a skilled workforce at Broken Hill, 60 km to the northeast.• It is close to road and rail infrastructure for access to the resource.• A high-grade, clean magnetic concentrate can be produced, with the only contaminant being silica.The deposit is a sedimentary siltstone which is considerably different to other known magnetite deposits. This caused significant differences in Davis Tube Recovery (DTR) results between laboratories so that the softness of the ore has required a close focus on, and changes to the laboratory procedures. A DTR procedure has been developed to provide consistent results across the deposit.Crushing and grinding test work has established a clear advantage in the use of the high-pressure grinding rolls (HPGR) crushing and grinding circuit for this particular ore. The power required for comminution using the HPGR crushing circuit is about half the power required for the Autogenous milling circuit.Therefore, despite the low magnetite grades, the Braemar Iron Formation in New South Wales and South Australia has the potential be a new magnetite iron ore province.

Jul 11, 2011

By Lilong Zhu, Shaoda Zhang, Qian Wang, Shengping He

The effects of ZrO2, Y2O3 and Sc2O3, which are transition metal oxides, on the melting temperature, viscosity at 1300 °C, and break temperature of three mold fluxes (two weak-reactive type and one non-reactive type) designed for the high manganese and high aluminum steels, and one another conventional CaO-SiO2 based mold flux is studied. The results indicate that the melting temperature and viscosity increases slightly, and the break temperature increases dramatically with the addition of ZrO2, Y2O3 and Sc2O3 content in the conventional CaO-SiO2 based mold flux system. While, the addition of ZrO2, Y2O3 and Sc2O3 in the weak-reactive or non-reactive mold flux systems has a negligible in fluence on the melting temperature, viscosity and break temperature, suggesting that these transition metal oxides are possible to regulate radiation heat transfer without changing the basic properties of mold fluxes.

Mar 1, 2018

By G. V. Sullivan

This report summarizes the results of a preliminary study concerning manganese extraction from low-grade dolomitic materials from the Philipsburg district in Montana by the Dean-Leute ammonium carbamate process. Studies were made to determine the relationship between the variables involved in treating these materials by a roast-leach process and the amount of manganese extracted. The variables studied were the roast temperature, the roast particle size, the molar ratio of NH3 to CO2 in the leach solution, the liquid-solid ratio in leaching, the leach time, and the size of the particles being leached. The roast-leach studies were statistically designed, and the experimental results were evaluated by an analysis of variance.

Jan 1, 1962

By Knud Sinding

Environmental reporting by mining firms takes many forms and change frequently. The objective of these reports is related to increasing the legitimacy of mining firms with their diverse stakeholders. This study, focusing on internet-based reports, shows that there are considerable variations in reporting. This phenomenon is interesting because it belies the efforts pursued by leading industry members under iniatives such as the Global Mining Initiative and the Mining, Minerals and Sustainable Development project. The observed variation, both internally among reports and between reports and other industry policy statements, suggests that the industry needs to explore the possibilities for more convergence in terms of reporting quality. Based on theoretical constructs from the management literature we present a series of arguments defining necessary and sufficient conditions for durable and well-institutionalized reporting practices and standards.

May 1, 2002

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962