Search Documents

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

By W. Collingwood

As openpit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in openpit mines is often recirculatory. This recirculation traps dust and gases in deep openpit mines. This problem is particularly acute in high-latitude openpit mines, due to a phenomenon known as atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In openpit mines, this can result in unhealthy accumulations of gases and other contaminants. In this study, the natural wind flow patterns in and around openpit mines were investigated using a computational fluid dynamics (CfD) program. Two-dimensional models were created for a variety of pit geometries. The effect of depth, slope angle and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2012

By T. R. A. Davey

A Survey of current and recent research and developmental work is supplemented by predictions for processes which should be developed over the reminder of this century.

Jan 1, 1970

This paper sets out to consider a specific type of corrosion protection system, which is referred to as a Duplex Coating system. The dictionary describes a duplex system as consisting of two elements or a “twofold” composition. The duplex system described in this presentation is such a two-part corrosion protection coating, viz, hot dip galvanizing as the firm base or primer, followed by a top paint system designed to combat severe corrosive environmental conditions encountered in nature. In principle, the duplex system is a cost effective and balanced, designed coating that is suited to the environmental conditions and service life requirements.

Jan 1, 2009

By S. K. Mitra

A refinement of the Seeger model for intersection process is investigated which is in better agreement with experimental observations than the original. It is shown that, in single crystals, the strain hardening in Stage II is mainly due to the short-mnge interactions when intersection is the rate-controlling process. It is also demonstrated that the creep curves, as predicted by this theory, are in good agreement with the experimental observations. MOTT: Cottrell? and Seeger have developed an approximate theory for plastic deformation of single crystals over the range of variables where the strain rate is controlled by the rate of intersection of dislocations. Although it is now generally agreed that the low temperature deformation of many pure metals is controlled by the intersection mechanism, various dictates of the over-simplified Seeger model are not in good agreement with all the experimental facts. It is the purpose of this paper to reveal that by appropriate extensions of the Seeger model, particularly those suggested by Basinski: a much more reliable theory results. The refined model to be presented here will be shown to account, in a satisfactory way, for the effect of stress, temperature, and strain on the creep rate under constant stress and for the effect of temperature and strain on the flow stress in constant strain-rate tests. EXPERIMENTAL METHOD To Check the theoretical deductions, both creep and tension tests were conducted on single crystals of high-purity Al (99.994 pct Al) so oriented that both the active slip plane and the Burger's vector of the operative dislocations on that plane made angles of about 45 deg to the tension axis. Single crystals of aluminum (5/8 in. by 1/10 in. by 8 in.) were grown in a graphite mold under an inert atmosphere using the Bridgman method. The chemical composition of the aluminum is given in Table I. A common seed was used for all crystals and their orientation is shown in Fig 3. The extensometry consisted of two differential transformers with matched outputs mounted so as to measure the extension in a 2 in. gage length. The amplified difference in output of the two transformers was recorded by a potentiometer. The amplification was calibrated before each run so that one chart division of the recording potentiometer indicated a 105 shear strain on the specimen. Stresses were measured to the nearest 1 x l04 dynes per sq cm. ACTIVATION VOLUME The concept of Basinski that the activation volume is not constant but is a function of the force that aids thermal fluctuation in effecting the cutting of dislocations will be adopted in this section. The force acting due to an applied shear stress on the dislocation being intersected is where L is the mean spacing between the forest dislocations, is the Burger's vector and T is the back stress. A detailed discussion about the origin of back stress will be taken up later in this report. As shown by Basinski, the activation energy, U, that must be supplied by a thermal fluctuation in order to effect intersection, is equal to where x is the distance through which the dislocation must be translated for complete intersection, and Fm is the maximum force encountered in intersection. When the applied stress is decreased abrupt ly F also decreases and the activation energy increases correspondingly as documented in Eqs. [ 1 ] and [2]. The Seeger equation for the strain rate when the deformation is controlled by rate of intersection of where the shear strain rate (per sec) N = the number of points per unit vol at which intersection can take place

Jan 1, 1962

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By R. Esteban, D. Runnels, J. Torrealba-Vargas, G. Couture

"Data handling is an important step in the development of a simulator of a mineral processing circuit. The model requires representative data of the scenario to be modeled. The model development involves protocols that must be followed very closely to complete a successful project.Data handling of large and diverse datasets (metallurgical test results, geological data, mining models, historical data, etc.) is a key element of the model. The information needs to be processed, reconciled, interpreted, modeled and presented to support the design or the optimization of a mineral processing plant.Best practice recommends that teams from different disciplines (such as mining, metallurgy, geology and environmental) interact to define the most important variables that could influence the simulator. For example by adopting a geometallurgical approach in the earlier stages of the project, it is possible to consolidate the number of main ore rock types in a testwork program (saving money and time) by involving geologists and metallurgists in the sample selection and data interpretation.Planning the development of a model involves an understanding of the software capabilities but also the limitations and the magnitude of the data required to calibrate the model in case of changes in the project.A successful model requires a deep understanding of the circuit to be modeled and thus plant personnel should be considered as members of the team.This paper describes the use of the "state of the art" tools for data analysis, simulation and optimization; and shows three practical examples of the use those tools in the design of mineral processing plants."

Jan 1, 2015

By I. A. Cameron, F. Ham, R. Sriram

"Planned increases in electric furnace productivity and higher matte temperatures needed for the Sudbury Smelter's S02 Abatement Plan, require an improved matte tap hole. Since startup in 1978, the matte tap holes have been incrementally improved by the addition of copper cooling blocks around the refractory tap blocks. These improvements provided a tap block life of about 100 taps per campaign.In July 1993, a prototype matte taphole was installed in Number 2 Electric Furnace to develop the technology to increase tap hole service life. The design was based on a heat transfer model of the tapping process to determine candidate refractory materials and cooler arrangements. The prototype tap hole features increased copper cooling, high conductivity refractories and extensive instrumentation. Eight trial campaigns are reviewed outlining the performance of silicon carbide and graphite refractories and typical heat loads during tapping.IntroductionFalconbridge Limited operates two 36 MYA, 6 electrode submerged arc electric furnaces in Falconbridge, Ontario. The furnaces, commissioned in 1978, smelt a partially roasted nickel-copper calcine, to produce matte for converting and slag for discard. Additional details of the smelter are available in the literature(1-4).Each furnace was equipped with two matte tap holes located in the furnace end wall. Early in the campaign, matte tap holes were identified as a weak area in the furnace which could be improved. From 1981 to 1987, incremental improvements were made to the design by the addition of water cooled copper blocks. In 1993, a prototype matte tap hole was designed and installed in Number 2 electric furnace to develop the technology to increase tap hole service life. Improved service life is required to meet planned increases in electric fWl1ace productivity and the higher matte temperature needed for the smelter's S02 Abatement Plan.This paper reviews matte tap hole development since 1978; outlines the prototype matte tap hole design, refractory selection and installation; and details the performance of the prototype tap hole during the first eight campaigns."

Jan 1, 1995

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By K. Tajrych

Time and again, lives are lost in underground cave-ins only be- cause there is no quick, sure way of locating the victims. When such accidents happen, rescuers must usually depend on the testimony of eye- witnesses for information on the whereabouts of trapped miners. Seldom is this information reliable. The witnesses themselves have just been through a traumatic experience that has distorted or destroyed their sense of time and place. A far more reliable method of finding men underground has recently been developed by the Coal Mining Research Institute of Ostrava, Czechoslovakia. With this system, a miner can be located with adequate precision even if he shows no sign of life. For the system to work, the miner need only have his electric cap lamp somewhere nearby. The system consists of a minute radio transmitter operated by the lamp battery (Fig. 1). This tiny transmitter continuously emits high- frequency electromagnetic waves that can be picked up by a sensitive direction-finder receiver in case of accident.

Jan 8, 1969

By Stephen C. Tadolini, Steve Bessinger, James Pile, Christopher Mark

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan’s geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro-active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

By L. D. Jaffe, John H. Hollomon

Fox many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure,1 and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearlitic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. QUENCH-CRACKING Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1946

By R. H. Eric, P. Taskinen, A. Bhalla, P. Halli

Sustainable development requires less energy consumption with lower carbon footprint. In this review the solid state reduction behaviour of three oxide ores using methane gas are briefly summarized based on experimental work conducted in our laboratories. The discussion concentrates mainly on mechanisms of the reduction studied through SEM-EDAX and X-ray diffraction techniques. Limited preliminary kinetic input is also mentioned. Iron ore containing titanium and vanadium could be reduced significantly in the solid state with methane-hydrogen mixture up to 400 °C lower than is needed in ordinary solid state carbothermic process. The reduction of chromite and manganese ores were possible similarly at lower temperatures with potential energy savings lower carbon footprint.

Mar 1, 2017

Jan 1, 1880

By W. J. Schlitt, K. McNaughton

A heap-leach field test was conducted during the 1993-1994 winter season at Carmacks, Yukon Territory, Canada. The purpose of the test was to demonstrate the viability of heap leaching Carmacks oxide copper ore in an arctic setting on a year-round basis. The test itself utilized a 5-m-diam crib loaded with 250 t of composite ore from the Carmacks copper deposit. The ore was stacked to a total height of 7 m in the crib, including 1 m of ore as an over- layer above the emitter system. This matched the plan for the commercial heap at the time when the test was started. The design also replicated an interior segment of the commercial heap. Leaching was done at a flow rate of 0.2 L/min/m2 using leachate at 21 °C. This temperature was maintained with no external heat input other than normal process heat transferred from electrowinning to the leachate via solvent extraction. Winter conditions were quite typical of those expected at the mine site. The temperature reached -54°C, while averaging -13°C over a three-month period. In spite of some flow system problems, leaching continued unabated, and freezing was limited to the insulating ore over-layer and isolated points near the outer crib walls. Thus, the test demonstrated that year-round heap leaching of Carmacks copper ore is practical in an arctic setting.

Jan 1, 2000

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011