Search Documents

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20 million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1 mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010

By P. N. Richards, M. K. Ormay

Commercially hot-rolled low-carbon steel strip may have one of two basic types of orientation texture, depending upon the amount of a iron which was present during the finishing passes. The changes in these textures with varying amounts of cold reduction up to 95 pct have been determined for the sheet surface plane and for parallel planes down to the mid-plane. The development of cold reduction textures has been reassessed on the basis of (200), (222). and (110) stereographic pole figures and pole density or inverse pole figure values. In agreement with the literature, it is shown that the textures can be described in terms of partial fiber textures but alternative descriptions are given for one of the fiber textures, in order to more closely correlate with experimental data. One partial fiber texture consists of orientations of the type (hkk)[011] extending from (100)[011] to {322}(011) in agreement with the literature. At moderate amounts of cold reduction, a second partial fiber texture forms with a <331> fiber axis inclined 20 deg to the sheet normal and a range of orientations centered on one close to (1 11)[112] and reaching to (232)[101] or (322)[011]. An alternative description involves a (111) fiber axis parallel to the sheet normal but capable of rotation about the rolling direction with rotation about the fiber axis. ORIENTATIONS developed in low-carbon steel strip after cold reduction are of commercial importance because they control, in part, the final preferred orientations after subsequent annealing. The method of control however is not understood completely. Some preliminary work indicated that the cold-reduced orientations and the subsequent annealing textures of commercial low-carbon steel were dependent on the orientations present in the material before cold reduction, that is, those present in the hot-rolled strip but, to date, the effects of initial orientations have not been extensively investigated. For this reason, much of the information given in the literature on development of preferred orientation is difficult to assess as details of initial texture and processing conditions are often inadequate or are altered by a subsequent heat treatment such as normalizing.&apos; It is known2 that anomalous results for near surface orientations may be obtained if lubrication during cold rolling is not adequate but whether lubricant was used during the experiments has not always been given, nor has the exact depth below the surface at which determinations have been made. A comprehensive review of cold rolling textures has been made recently by Dillamore and Roberts&apos; and more restricted recent reviews are due to stickels4 and Abe.5 Based largely on the experimental work of Bennewitz,1 reviewers have accepted that the preferred orientations produced on cold reducing low-carbon steel can be described in terms of two partial fiber textures as follows: Partial Fiber Texture A which has a (011) direction in the rolling direction and includes orientations within the spread from (211)[011] through (100)[Oll] to (211)[011.]; there is some controversy as to whether it extends as far as the orientation (111)[011]. As Dillamore6 has observed, the extent of this partial fiber texture depends on the intensity levels selected. Partial Fiber -texture B which has a (011) direction located 60 den from the rolling direction in the plane containing the rolling direction and the sheet normal. There are two directions which satisfy these conditions and orientations in this partial fiber texture extend from (21l)[0ll] through (554)[225] to (121)[101]. The orientations {211}(011) are members of both partial fiber textures A and B and it can be noted that a variant of {554)<225> is within 6 deg of a variant of {111}(112). Barrett7 had postulated earlier that, in addition to orientations which would fall into partial fiber texture A, a true fiber texture with a (111) direction in the sheet normal was present after heavy cold reduction. This fiber texture would include orientations such as {111}(011) and {111}(112). Later investigators, notably Bennewitz,&apos; have discounted this, mostly on the ground that the partial fiber textures A and B, as described above, contain all the strong orientations that have been observed. However in other work it has been reported2 that (222) pole density or inverse pole figure values show a continuing increase with increasing reduction by cold rolling and give values considerably greater than for any other low indices plane. Thus it could be inferred that a (111) fiber texture as described by Barrett would be one which becomes more dominant with increasing cold reduction, whereas Bennewitz&apos; concluded that components such as {554)(225) in partial fiber texture B began to decrease in intensity at high reductions. Following Bennewitz, one would expect a decreasing (222) pole density value (parallel to the sheet normal) with increasing cold reduction. Because fiber textures consist of grains with a range of orientations that have one axis in common, it has been inferred that during deformation the crystal orientations rotate about the fiber axis&apos;74 and that the orientations of crystals that at one stage belong to one fiber texture can rotate on further cold reduction into the other fiber texture through an orientation in which the two fiber textures intersect.&apos; For example,

Jan 1, 1970

By G. J. Karabin

The Boundary Element Method of Numerical Modeling has become an increasingly popular rock mechanics -mine design tool. It has been used by the Roof Control Division, Pittsburgh Safety and Health Technology Center, MSHA, to aid in the resolution of complex ground control problems since 1985. This paper will present an overview of an evolving simulation process and details of methods utilized to generate necessary coal, rock and gob input properties. Also included is a description of a Deterioration Index System that is used to link model output to observed mine conditions and two case studies to illustrate that process.

Jan 1, 1995

By LIONEL E. BOOTH

ORE tests are made for the purpose of determining the correct methods of treatment for any particular ore. They should be conducted so as to insure that the results obtained in actual mill practice, on ore of similar grade and physical nature, will duplicate the results obtained in the test work. As the expenditure of many thousand of dollars may be involved in the building of the necessary mill, the testing of ores calls for extreme care and skill in handling laboratory machines, and a knowledge of actual practice to guard against the danger of obtaining results in test work that would be impractical to duplicate on a commercial scale. The importance of a correct sample of the ore is at once apparent. No matter with what degree of care the test 4rk is done, it loses its value when made on an unrepresentative sample. It is the first safeguard against future disappointments in the loss of capital and time. A number of failures in the past have been traced directly to faulty or lax methods in obtaining the ore sample.

Jan 1, 1924

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite/Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Company to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the Company&apos;s main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received substantial attention in recent years. A Company guideline that no coal shipment shall exceed any contract or company-imposed coal quality specification has been successfully implemented. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed. Background Surface coal mining of subbituminous C rank coal in the Cillette. (Campbell County) Wyoming area has become increasingly competitive during recent years. Prior to 1974, one small surface mine produced coal for local consumption. During the last ten years, 13 new surface coal mines have been constructed. Coal production from Campbell County, Wyoming totalled 88 million short tons (79.8 million metric tons) in 1983, the majority being shipped to electric utilities in the central and southern United States via unit trains having a capacity of 10,000 short tons (9,072 metric tons).

Jan 1, 1984

By Philip Lindstrom

Retreat mining, using yielding steel friction props, over a seven-year period has been successful at a uranium mine operated by Hecla Mining Company in southeast Utah. The support system allow good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered, Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths.

Jan 1, 1964

By Henry M. Howe

The object of the present paper is to suggest injecting into the hearths of iron blast furnaces, whose temperature has become unduly lowered, some form of fuel whose calorific intensity, under the peculiar conditions existing there, is considerably higher than than of liquid petroleum, the rose of this substance for melting out chills having grievonsly disappointed the high hopes which were at first entertained of it. A chill being a fall of the temperature below that needed for the complete liquefaction of the slag, which requires, according to Plattner, about 1800&apos; C., one would suppose that the chief thing to be accomplished in curing it would be to raise the temperature in the crucible of the furnace. The most obvious ways of doing this seem to be to raise the temperature of the blast, and to increase the amount of fuel in the crucible itself. Simply increasing the rate at which the blast enters the furnace, if carried beyond a certain point, should lower the temperature in the crucible. The existence of a chill shows that the fuel is arriving too slowly at the tuyeres. If air be introduced so rapidly as to he in excess of that required for the combustion of the fuel, all that excess will simply lower the temperature around the tuyeres, carrying the region of intense heat upwards, and weakening its intensity by increasing its size. Up to a certain point, increasing the rate of introducing the blast will increase practically pari passu the rate at which the fuel reaches the tuyeres. But when mechanical obstructions, which so often accompany chills, retard the descent of the fuel, there must be a point beyond which this does not hold good, and beyond which farther

Jan 1, 1883

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By James H. Cobbs

The purpose of this study is to investigate the application of boring equipment to the production of anthracite coal from steeply pitching beds. Both raise boring and augering equipment were considered. Previous studies (11) have indicated that boring equipment may have definite applications to the development of steeply pitching anthracite beds. This investigation was to carry forward previous work to determine the possible application of the two different types of equipment being considered. Previous conclusions have been substantiated by the results of this study.

Jan 1, 1975

By W. J. Skewes, C. T. Holland

Properly constructed stopes are necessary underground for proper ventilation and safe, healthful working conditions. Mining companies are concerned with providing the best possible stoppings at an economic cost. It is important to consider 1) proper materials, 2) construction that ensures maximum performance from the material used, and 3) keeping costs within reasonable limits for the unit operation—stopping—involved. The authors investigated all aspects of the problem and have attempted to layout a study program to provide information on all phases. Mining companies every year purchase huge amounts of material for the construction of ventilation stoppings. This material by the time it is in place in the stoppings will cost the company many thousands of dollars. In addition and more importantly these stoppings are supposed to confine air travel along certain well defined paths into areas where it is needed to provide safe and healthful atmospheres for workmen. The cost of forcing this air through the mine is large and in general increases as the total quantity increases. Consequently, if the stoppings leak, increased cost results and in addition unsatisfactory ventilation may prevail in the mine. Therefore, it is essentia1 to provide the best possible stoppings at an economic cost. When attempting to provide the best stoppings possible at an economic cost, three aspects of the problem must be considered. These are 1) getting the most suitable material for stopping constructions, 2) constructing the stopping so as to get the best performance from the material used, and 3) keeping the cost of stopping construction to a minimum for a suitable stopping. This investigation is concerned with all phases of the problem and has attempted to lay out a study to provide information on all of them. In order to develop information on the best stopping material available it seemed wise, after con- sidering the job a stopping must do, to investigate the following aspects of material used for stoppings: 1) strength in compression, 2) compressibility or yield under load, 3) porosity, and 4) permeability. To provide information on the best manner of construction the following aspects of air leakage through the stopping were investigated: 1) when the stopping is built of dry stacked materials—i.e., the joints are not mortar-laid (See Fig. 1); 2) when the stopping is built of dry stacked material and then plastered on one side (see Fig. 2); 3) when the

Jan 1, 1961

By H. Tomlinson

"PURPOSE OF REPORTFatalities from falls of roof and coal are responsible for the death of more than 1,000 miners annually in the bituminous coal mines of the United States or practically one—half of the total fatalities in and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal—mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years.The necessity for studying falls of roof and coal becomes apparent by referring to the following data from a table by Adams and Chenoweth:3"

Jan 1, 1933

By J. Guha, el, G. Bouchard, W. Zuckerk, J. Carignan, G. Archambault

The Gwillim Mine, located 8 km northwest of Chibougamau, is underlain by two mafic volcanic cycles separated by a dominantly felsic cycle. These rocks are part of the Gilman Formation of the Roy Group. The mafic rocks are cut by weak shear zones containing the "North" and "Main" veins, both east-west striking gold-bearing structures dipping 75° to the north. The felsic cycle, which is also gold-bearing, contains textures suggesting a syngenetic origin. The Gwillim Mine presents an excellent opportunity for the study of what may be two coexisting gold deposits, a volcanogenic and a veine type.

Jan 1, 1984

By L. Klatzel-Mudry, D. J. Nikols, J. D. Hughes

"The Geological Survey of Canada Paper 88-21, A Standardized Coal Resource/Reserve Reporting System for Canada, is referenced by National Instrument 43-101 for the preparation of resource and reserve estimates on coal deposits. However, for all disclosure of mineral resources or mineral reserves for coal, issuers are required by NI 43-101 to use the equivalent mineral resource or mineral reserve categories set out in the CIM Definition Standards and not the categories set out in Paper 88-21. “Because the framework is based on Canadian deposits and their tectonic regimes, the Canadian Securities Administrators believe it is not reasonable to apply Paper 88-21 to foreign coal properties. The “Resource Links” at the end of this volume provide website links to guidance documents for preparing coal resource and reserve estimates in Australia, South Africa, and the USA.”This report discusses definitions, concepts and parameters used to determine coal resource and reserve quantities, and provides a framework to facilitate consistent categorization of coal quantities found within various depositional and tectonic regimes in Canada.Coal deposits, or portions thereof, are first categorized in terms of their geological complexity <Geology Type), and probable recovery method (Deposit Type). Methods for determining quantification parameters including seam thickness, areal extent and bulk density are outlined for each geology/deposit category. Within each geology/deposit category, coal resources are further divided, based on their assurance of existence, into measured, indicated, inferred and speculative subdivisions and, according to their feasibility of exploitation, into immediate and future interest subdivisions. Coal reserves within each geology/deposit category are subdivided according to whether they are within or outside active mining areas, and may be reported on in place, recoverable and saleable bases.A wide cross-section of the coal industry in Canada contributed to the development of this reporting system. To ensure that the parameters and concepts expressed in the system continue to reflect technological and economic realities in the future, the Coal Association of Canada has established a committee to facilitate periodic reviews."

Jan 1, 2003

By D. J. Bauer

A solvent-extraction system employing selective stripping of a pre loaded organic phase was investigated for recovering Sm203 from a light-group rare-earth mixture. The samarium concentrated in the organic phase, and a >99-pct-pure samarium oxide product was obtained at 76-pct recovery in a 20-stage operation using di(2-ethylhexyl) phosphoric acid (EHPA) as the organic phase. The stripping agent was a 1.5-pct hydrochloric acid solution containing 200 g NH4C1/1.

Jan 1, 1972

By Rov G. Stott

In recent years there has been no loss of life from fires in the underground mines of the Lake Superior district, but numerous minor fires and several serious ones involving loss of property and production have occurred. The iron-ore-producing companies recognize that well-equipped mine rescue stations are a valuable asset against the ever-present ranger of mine fires or the possibility of hazardous atmospheric conditions underground. Prompt action by trained and properly equipped rescue teams is recognized as the prime essential in saving lives, property, and production when fires occur. To achieve this purpose, the mining companies have provided themselves with mine rescue equipment and maintain trained mine rescue crews. This circular describes how one progressive company has provided, maintained, and improved upon such protection for its underground iron-ore mines on the Marquette and Menominee iron ranges of Michigan&apos;s upper peninsula. SUMMARY The central mine rescue station of The Cleveland-Cliffs Iron Co. at Negaunee, Mich., has provided the company&apos;s mines with competent and well-equipped mine rescue teams. The new central mine rescue station at the Mather mine "B" shaft has the distinction of having underground training facilities provided as a part of the station. The company maintains the largest trained force in mine rescue in the Lake Superior district, and mine rescue training is employed as a part of the accident-and fire-prevention program. One of the most important results has been the promotion of closer cooperation and understanding between the management and the workmen. In addition to the service rendered to company mines, the station and its personnel have given assistance to others. The station and its equipment have also been used for training several nearby community volunteer fire departments. This mine rescue station and its personnel have been a dependable and valuable asset to the community in which it is located.

Jan 1, 1954

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001